PARIS TEXAS HARDWARE R-TEC Wall Mount Track System Installation Guide
- June 12, 2024
- PARIS TEXAS HARDWARE
Table of Contents
R.TEC AUTOVATIOby® Rowley®
THE FINIAL COMPANY™ 1 3 /8″ R-TEC AUTOMATION® METAL TRAVERSE CENTER OR ONE-WAY
DRAW SYSTEM INSTALLATION INSTRUCTIONS
Please read all instructions before starting
INTRODUCTION:
TFC™ 1 3/8″ R-TEC Automation®Metal Traverse Systems are used to electronically
control the drapery using a Slim Drapery Motor and Remote Control. By using a
Remote Control or the-TEC Automation® App via a smartphone or tablet, the
operator can open and close the drapery smoothly and precisely.
The maximum width for this system is 12′ continuous (in select finishes) and
24′ spliced. The minimum width for this system is 37″. The maximum drapery
weight is 77 lbs. Single or Double System.
BRACKET ASSEMBLY:
TFC™ 1 3 /8″ R-TEC Automation® Metal Traverse Systems can be mounted on the wall or ceiling. NOTE: The bracket shafts are attached to the track.
Wall options include single brackets with either a 3 1/2″ or 6″ projection, or
a double bracket with 3″ and 7 1/2″ projections.
Ceiling options include a single or double bracket with 2 3 /8″ drop, or a
low- profile ceiling bracket with a 5/32″ drop.
PARTS LIST
Basic Components:
- R-TEC Automation® Metal Track
- Brackets
- Slim Drapery Motor
- Li-ion Battery power option
- AC / DC Power Transformer power option
BRACKET PLACEMENT:
It’s recommended to use 1 bracket beside each pulley and an adjacent bracket
no more than 24″ away. On the remaining part of the Metal Track, bracket-to-
bracket distances should be no more than 48″. Also, 1 bracket should be placed
on each side of a splice if used.
INSTALLATION:
We recommend using a professional installer. Installation hardware is
included. The fasteners (screws and mollies) may not be appropriate for every
installation or wall material. Brackets and holdbacks should be installed
securely into wall studs when possible. The Finial Company™ will not assume
responsibility for damages incurred by improperly mounted or inadequately
supported hardware.
WALL MOUNT TRACK SYSTEM INSTALL:
NOTE: Installer is responsible for determining the correct mounting fastener and wall location per the wall construction type.
Step 1. Locate bracket base plate.
Step 2. Mount wall mount base plate to wall.
Step 3. Locate bracket base cover.
Place cover over wall mount base plate. Turn cover clockwise to lock in place.
Step 4. Locate track system. Place track system onto the wall mount base
plates. Step 5. Tighten all wall mount stems with set screw located above
the wall mount cover.
CEILING MOUNT TRACK SYSTEM INSTALL:
NOTE: Installer is responsible for determining the correct mounting fastener and wall location per the wall construction type.
Step 1. Locate ceiling plate.
Step 2. Mount ceiling plate to ceiling. Step 3. Locate ceiling
bracket cover.
Place cover over the ceiling plate. Step 4. Locate the insert. Screw the
insert on the ceiling plate. Step 5. Locate track system. Place track
system onto the ceiling mount inserts. Step 6. Tighten all ceiling mount
stems with set screw located close to the ceiling mount cover.
LOW-PROFILE CEILING BRACKET TRACK SYSTEM INSTALL:
NOTE: Installer is responsible for determining the correct mounting
fastener and wall location per the wall construction type.
Step 1. Locate track system and mount it to the ceiling.
NOTE: The Low-Profile Ceiling Mount Bracket is already attached to the
track.
NOTE: Glides can be added or removed
with the Drive Pulley installed by removing the End Stop.
Install the Pendant into the End Stop.
Install
the End Stop.
DOWNLOAD INSTRUCTIONS:
https://qrs.ly/smcl93q
www.TheFinialCompany.com
updated 03/20/2023
THE FINIAL COMPANY™
Documents / Resources
|
PARIS TEXAS HARDWARE R-TEC Wall Mount Track
System
[pdf] Installation Guide
R-TEC, R-TEC Wall Mount Track System, Wall Mount Track System, Mount Track
System, Track System, System
---|---
References
- Home | The Finial Company
- rowleycompany.scene7.com/is/content/rowleycompany/tfc-metal-product-instruc-motor-rtec-center-one-way-drawpdf