ALPINE INA-W910R Advanced Navi Station Instruction Manual

ALPINE INA-W910R Advanced Navi Station

Specifications

• Screen Size: 7.0 inches
• Number of Picture Elements: 1,152,000 pixels
• FM Tuner Tuning Range: 87.5 – 108.0 MHz
• MW Tuner Tuning Range: 531 – 1,602 kHz
• LW Tuner Tuning Range: 153 – 281 kHz
• Navigation Received Frequency : 7.0
• Receiving Sensitivity: 1,152,000 pixels
• Power Requirement: 14.4 V DC (11-16 V allowable)
• Maximum Power Output: +4 dBm Max. (Power class 2)
• Weight: 2.7 kg (5 lbs. 15 oz)

Installation

• When making connections to the vehicle’s electrical system, be aware of the factory-installed components (e.g. on-board computer). Do not tap into these leads to provide power for this unit. When connecting the
  INA-W910R to the fuse box, make sure the fuse for the intended circuit of the INA-W910R has the appropriate amperage. Failure to do so may result in damage to the unit and/or the vehicle. When in doubt, consult your ALPINE dealer.

• The Display must be completely retracted in the casing when installed. If it is not, problems may occur

1. When installing in automobiles, make sure the Display can open/close without coming in contact with the shift lever.
2. About the installation angle, please install as horizontally as possible within the following angle range. If the installation angle is beyond the range, the current position may not be correctly displayed and a maloperation may be caused for the navigation mode.
3. The unit can be installed in the mounting sleeve in three positions by aligning its mounting holes (A to C) on the sides of theunit. Position A will be used in most cases. If B or C are to be used, the hole positions need tobe modified.
4. If B or C is used, make sure that there is a enough space depthwise before installing the unit. If the unit is forcibly pushed into the mounting sleeve, damage may occur.

Mounting Hole Position

Depending on the position chosen, the front panel will protrude differently.

Position A
If the installed mounting sleeve is loose in the dashboard, the pressure plates may be bent slightly to remedy the problem.

How to use a Seal

• If A is used for installation:

• Affix the seal so that mounting holes B and C are covered.

• If B is used for installation:
  Affix the seal so that mounting holes A and C are covered.

• If C is used for installation:
  Affix the seal so that the mounting holes A and B are covered

Installing the Face Plate

• If A is used, the supplied face plate may be mounted.
• If B is used, the face plate must be modified before installing it.
• To modify the face plate, consult your Alpine dealer.
• If C is used, the face plate cannot be mounted.
• Consult your Alpine dealer

For the screw marked “*2”, use an appropriate screw for the chosen mounting location

• Slide the INA-W910R into the dashboard until it clicks. This ensures that the unit is properly locked and will not accidentally come out from the dashboard.

Install the GPS antenna

For inside vehicle

1. Stick the ground pad at the center of the dashboard and close to the windshield within one-inch distance.
2. Attach the GPS antenna to the center of the ground pad.
   (The cable side faces the back of the vehicle.)

For outside vehicle
At the front or back of the vehicle roof.

Wiring the GPS antenna cable
Do not bend or fold the GPS antenna cable.

• When installing the INA-W910R to the vehicle, make sure the back of the unit and the cable are not bent.

Connect the GPS antenna
Securely connect the GPS antenna connector to INA-W910R.

Connections

Connections-1/2 /

Set the system switch to “NORM” when only a changer is connected (when the Ai- NET compatible equalizer is not used). When the IMPRINT audio processor is connected, set to EQ/DIV position

Connections-2/2 /

Connection Diagram of SPST Switch (Sold Separately)
(If the ACC power supply is not available)

• If your vehicle has no ACC power supply, add an SPST (Single-Pole, Single-Throw) switch (sold separately) and fuse (sold separately).
• The diagram and the fuse amperage shown above are in the case when INA-W910R is used individually.
• If the switched power (ignition) lead of the INA-W910R is connected directly to the positive (+) post of the vehicle’s battery, the INA-W910R draws some current (several hundred milliamperes) even when its switch is placed in the OFF position and the battery may be discharged

FAQ

• Q: Can the display open/close without coming in contact with the shift lever?
  • A: Yes, it is important to ensure that the display can open and close freely without any interference.
• Q: What is the recommended installation angle for the unit?
  • A: The unit should be installed as horizontally as possible within the specified angle range to ensure correct display and navigation functionality.
• Q: How do I install the unit into the mounting sleeve?
  • A: Before installing the unit, remove the mounting sleeve from the main unit and attach it to the vehicle. Then, insert the main unit into the mounting sleeve depthwise to avoid any damage.

References

• Manual-Hub.com – Free PDF manuals!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>