Hamilton Beach HBH750 BAR BLENDER Instruction Manual

Hamilton Beach HBH750 BAR BLENDER

IMPORTANT SAFETY INSTRUCTIONS

•  Read the Operation Manual before using blender. Keep Operation Manual handy.
•  Before first use, wash container assembly in hot, soapy water. Do NOT place in dishwasher.
•  Plug into a grounded outlet.
•  Do not remove ground.
•  Do not use an adapter.
•  Do not use an extension cord.
•  Disconnect power before cleaning or servicing.
•  To reduce the risk of personal injury, unplug the cord from the outlet when not in use and before putting on or taking off parts.
•  Unplug the blender and inspect the power cord insulation for cracks on a weekly basis. Refer to “Technical Services” for repair or replacement.
•  To protect against electrical shock, do not immerse cord, plug, or blender base in water or any other liquid.
•  Do not spray the base with a high pressure spray gun.
•  Extreme caution must be used when moving an appliance containing hot oil or other hot liquids.
•  Do not use appliance for other than intended use.
•  Not intended for use by or near children. Children should be supervised to ensure that they do not play with the appliance.
•  The appliance is not intended for use by persons (including children) with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
•  Read the Operation Manual before using blender. Keep Operation Manual handy.
•  Before first use, wash container assembly in hot, soapy water. Do NOT place in dishwasher.
•  Plug into a grounded outlet.
•  Do not remove ground.
•  Do not use an adapter.
•  Do not use an extension cord.
•  Disconnect power before cleaning or servicing.
•  To reduce risk of personal injury, unplug cord from outlet when not in use and before putting on or taking off parts.
•  Unplug the blender and inspect the power cord insulation for cracks on a weekly basis. Refer to “Technical Services” for repair or replacement.
•  To protect against electrical shock, do not immerse cord, plug, or blender base in water or any other liquid.
•  Do not spray the base with a highpressure spray gun.
•  Extreme caution must be used when moving an appliance containing hot oil or other hot liquids.
• Do not use appliance for other than intended use.
•  Not intended for use by or near children. Children should be supervised to ensure that they do not play with the appliance.
•  The appliance is not intended for use by persons (including children) with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

WARNING

• Electrical Shock Hazard Disconnect power before cleaning blender base.
• Failure to follow these instructions can result in death or electrical shock
• Cut Hazard
• The blending blade is sharp.
• Always place lid on container when blending.
• Do not put hands, spoons, or other utensils in container when blending.
• Failure to follow these instructions can result in broken bones, cuts, or other injuries.
• Electrical Shock Hazard
• Plug into a grounded outlet.
• Do not remove ground.
• Do not use an adapter.
• Do not use an extension cord.
• Failure to follow these instructions can result in death, fire, or electrical shock.

Parts and Features

Technical Services

For assistance or replacement parts, call our Technical Services number: 866-285-1087 or 910-693-4277 8 a.m. – 5 p.m. EST Monday – Friday www.hamiltonbeachcommercial.com

Replacement Parts

The following components are subject to wear and should be replaced at least yearly. We recommend keeping a replacement container on hand.

Optional

To Load Custom Programs with the Memory

Card:

•  Turn OFF (O) and unplug unit.
•  Remove the memory card cover.
•  Insert memory card.
•  Plug in unit and turn ON (Reset) (I).
•  Display will show a confirmation message.
•  Turn OFF (O) and unplug unit.
•  Remove memory card and reinstall the memory card cover.

Control Panel

Blender Operation – Quick Start Guide

•  Read Important Safety Instructions and Warning Symbol Explanations before use.
•  Place the blender on a dry, level surface.
•  Make sure the power switch is OFF (O). Plug the blender into a grounded 3-prong electrical outlet.
•  Place the container on the base with ingredients and container lid in place.
•  Turn the blender on by pressing the Power Switch marked Reset [ON (I)] / OFF (O). The red LED switch indicates that power is ON (I).
•  Select the desired function.
•  Use any button to stop operation

Warning

Sanitizing

• Sanitize using 1 tablespoon (15 ml) of household bleach per 1 gallon (3.8 liter) of clean, cool water (60°F/16°C), mixed according to the instructions on the bleach.
•  Fill container with sanitizing solution, replace lid and filler cap and run on LOW speed for 2 minutes. Empty container.
•  Wipe exterior with soft cloth dampened with sanitizing solution.
•  Immerse lid and filler cap in sanitizing solution for 2 minutes.
•  Place empty container on base and run on HIGH speed for 2 seconds to remove any moisture from the cutter assembly.
•  When ready to use, rinse with clean water.

Using the Controls

important  instruction

Troubleshooting Guide

Make sure that the Power Switch is in the ON (Reset) position and is illuminated red.

• Check to see if unit is securely plugged into an electrical outlet of the proper voltage and frequency.

• Check to see if the fuse for the electrical outlet has blown or if the Power Switch has tripped.

• This blender is equipped with motor overload protection. If the motor stops during operation due to overheating, unplug and allow the blender to cool down for 15 minutes. Plug blender back in after 15 minutes to resume normal operation.

Blender fails to start or stops while it is running; message appears in display.| • Make sure that the jar is seated properly on the blender base.

• Blender will not operate unless jar is properly seated.

• Make sure Quiet Shield™ is down and in correct position.

Blender fails to start or stops while it is running.| • Thermal overload protection has been tripped. Attempt to run “cool down cycle.” Follow instructions in display.

• This blender is equipped with motor overload protection. If the motor stops during operation due to overheating, unplug and allow the blender to cool down for 15 minutes. Plug blender back in after 15 minutes to resume normal operation.

Unit does not respond to button commands or error message appears in display.| • Turn the power off and back on using the power switch to reset the controls.

• Turn the power off and back on using the power switch. If the error message still appears, the unit will need to be serviced.

Ingredients will not mix properly.| • Check to see if enough liquid has been added to the ingredients. Mixture should be fluid and free-running at all times.

• Solid pieces are too large.

• Container is too full. Do not fill past highest graduation marking.

• Cutter assembly blades are not sharp or are damaged. Inspect container and cutter assembly daily. Replace cutter assembly at least yearly or sooner if cutter assembly appears worn or damaged.

• Check to see if cutter assembly is installed properly.

• Select speed to create a fluid blend.

Maintenance

Daily| Unplug the blender, remove the container from the base, and then inspect the container and cutter assembly for wear, nicks, and broken or loose blades. If the blades are nicked, broken, or loose, discontinue use immediately and replace the container or cutter assembly. See “Replacement Parts.”
---|---
Weekly| Unplug the blender, and then inspect the power cord insulation and power plug for cracks. Refer to “Technical Services” for repair or replacement. Remove jar from blender base. Inspect the cutter by rotating the drive end of the cutter by hand. It should turn smoothly. If it does not, replace the container or cutter assembly.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>