Hanwha Vision SHD-3000F5 In Ceiling Housing Instruction Manual

: June 14, 2024
: Hanwha Vision

Table of Contents

OVERVIEW
WHAT’S INCLUDED
INSTALLATION INSTRUCTIONS
HOW TO INSTALL

Hanwha Vision SHD-3000F5 In Ceiling Housing

OVERVIEW

This In-CEILING HOUSING is a mounting ADAPTOR that is designed to mount PNM- 9000VQ in built-in style on a double-layer ceiling.

WHAT’S INCLUDED

HOUSING

SAFETY BRACKET (1EA)

SAFETY WIRE (1SET)

TEMPLATE (1EA)

INSTALLATION MANUAL

INSTALLATION INSTRUCTIONS

Select an installation position or place that can endure more than 4 times of the total weight of the installation structure.
At least 250mm or more of spare height is required above the CEILING BOARD.
CEILING BOARD’s thickness should be less than 50mm.
Be sure to secure the SAFETY WIRE to avoid a product fall.
If you want to attach the camera to the ADAPTOR, use the only provided SCREWS.
(SCREWS are shipped with PNM-9000VQ. To learn how to use them, see Step 3 on page 5.)
CEILING BOARD must be able to sustain the weight of at least 10 kg.

HOW TO INSTALL

Place the TEMPLATE on the CEILING BOARD and drill a guided hole.
Remove the round filling (“C”) from the TEMPLATE.
Place TEMPLATE A onto the CEILING BOARD to which you will attach the ceiling mount ADAPTOR and drill a hole of Ø326mm in diameter.
See the figure below for the hole shape.
Remove the CAP and NUT that fit to the size of the HOLE you are going to use.
Remove the Dome Cover and Mounting Plate according to the Disassembling section in the PNM-9000VQ manual.
Join the MOUNTING PLATE to the Housing using the SCREWS shipped with PNM-9000VQ.
Fix the ANCHOR BOLT onto the concrete CEILING, and secure the SAFETY WIRE to the
ANCHOR BOLT as below:
Tighten the NUT (“N1”) on the ANCHOR BOLT.
Insert the provided SAFETY BRACKET into the ANCHOR BOLT.
Tighten two NUTs (“N2”,”N3”) onto the ANCHOR BOLT.
Hook and fix one end of the SAFETY WIRE onto the SAFETY BRACKET.
Hook and fix the other end of SAFETY WIRE onto the HOUSING as shown below:

• The ANCHOR BOLTs and nuts are optional and not included in the product package.
• ANCHOR BOLTS must be able to sustain the weight of at least 30 kg.
• If you proceed without following the instructions in the manual, that is if you work with the camera body already attached from the beginning, the safety wire could exceed its limit and be broken when the housing is accidentally dropped, which could result in an accident.

6. After fixing the SAFETY WIRE to the HOUSING, tighten the screw in the SAFETY RING to the end.

In the case that the pipe is to be connected to the External Cable hole, the pipe must be inserted within the depth of 15mm or less.
To connect to the camera, insert the external cable through the Cable hole on the housing to the inside of the housing as shown in the figure.
• Refer to the installation manual of the camera that you want to install, and prepare necessary cables for camera connection.
Push the HOUSING inside the CEILING through the CEILING hole, and tighten the SCREWs (x2) clockwise to fix the HOUSING on the CEILING. (The BRACKET will be positioned from to as shown.)
• Using a power tool for installation could cause product damage.
If you are going to use a power tool, the torque must be 30 Nm or less.
• Ensure that the HOUSING is firmly secured to the CEILING BOARD.
Proceed with the rest of the installation process for PNM-9000VQ according to the sections next to Disassembling in the PNM-9000VQ manual.
Align and attach the COVER to the HOUSING following the arrow, and push it hard so that four VELCROS are firmly attached to it.
When all VELCROS are attached, tighten the four SCREWS on the COVER to fix it to the HOUSING.
• Since VELCROS are lightly attached to the surface, they can easily be detached.
Therefore, the screws need to be tightened immediately after attaching the VELCROS.