BARSKA BC128 Biometric Security Door Lock Instruction Manual

BARSKA BC128 Biometric Security Door Lock Instruction Manual

• Thank you for purchasing this product
• Read this manual thoroughly before use
• Keep this manual for the convenience of future reference

Notice

1. Keep your fingers clean when using this product.
2. In the state of new lock (factory setting), the lock can be unlocked with any fingerprint.
3. When opening the door, if the lock beeps an alarm and the indicator light flashes red, it’s indicating the lock is in insufficient voltage level. Please change the batteries.
4. This product can save 99 fingerprints, among which 3 are master fingerprints (Code: 00-02), and other 96 are member fingerprints (Code: 03-98). Additionally there is also a set of spare password for unlocking (Code: 99).
5. Deletion of fingerprint is to delete each fingerprint separately according to its code; the fingerprint cannot be deleted unless you know the code.
6. The dirt on the surface of fingerprint collection window may affect the normal use. Therefore please keep it clean.
7. Do not clean the lock surface with corrosive substance, or else the protection layer may be damaged and thus influence the gloss of the lock surface. Therefore please clean the lock surface periodically with furniture polish wax (e.g. Pledge )
8. If the latch bolt fails to draw back and forth freely, or the door cannot be closed normally due to the distortion of the door, please adjust the strike plate’s position.
9. When the fingerprint and password fails to work, use the mechanical key to open the door; please keep the mechanical key in a proper place.

Right method to apply fingerprint

Notes:
When the red light on fingerprint collection window flashes, press your finger onto the window, and then remove your finger after a beep; press your finger again after 2 seconds, if you hear two long beeps, the collection is successfully completed.

Error in applying fingerprint

Name of the parts

Lock body (front)

Lock body (back)

**Side

**

Door Lock Operation Instructions

Instructions of the lock buttons

state)

Indication of the lock state

1. Operation succeeded: green light on, with two long beeps.

2. Operation failed: red light on, with two short beeps.

3. Door open: electric engine makes a rolling sound for the first time, which indicates the lock is in door open state.
   Door closed: electric engine makes a rolling sound for the second time, which indicates the lock is in door closed state.

4. Enter passage mode: the lock makes a beep, and after the successful setup, the green indicator light flashes every 5 seconds.Refer to P.18 for passage mode setup.

Assignment of fingerprint and password

Note:
The three master fingerprints can delete each other. At the deletion of the last master fingerprint, the lock resumes to the factory setting

Initialization of the door lock

Specific operations:

a) Press the on battery cover button, slide the battery cover upward and remove it, you can see one hole at each side, and inside each hole there is a button for setup Specific operations:
b) Remove either of the four batteries, pressing the buttons on the front side to confirm the power is successfully cut off, then insert into the two holes to press the buttons inside with two slim objects (e.g. iron wire) at the same time, hold it tight (not to release), and reload the battery. The lock is then re-powered, if you hear a toot sound after 5 seconds, the initialization of the lock is successfully completed, and you may loose the slim objects.

Note:
After initialization of the lock, all the enrolled fingerprints and password in the lock are cleared, and the lock resumes to the new lock state (factory setting). Any finger can open the door, and master fingerprints, member fingerprints, as well as spare passwords need to be set again.

Enrollment of master fingerprints / member fingerprints

Enrollment of master fingerprints (take user 01 as an example)

In the state of new lock, put any finger on the fingerprint collection window to enter the door open state| Green light is on, and the LED displays —
Press Button + to enter the enrollment mode| A beep sound heard, and the LED displays 0-
Press Button + or – to adjust the first digit 0 of the fingerprint code, and press Button # to confirm the choice| The tens place displays the figure that has just been set, while the ones place displays 0
Continue to press Button + or – to adjust the second digit 1 of the fingerprint code, and press Button # to confirm| The LED displays the fingerprint code 01 flashing
Press Button # to reconfirm the fingerprint code 01| The LED displays fingerprint code 01 , with red light on the fingerprint window
Put the finger to be enrolled on the fingerprint collection window, and collect twice| When the red light of the fingerprint window is on, press with the finger; after the beep, remove the finger and press one more time. A long beep will sound and the two collections are successfully completed
The first master fingerprint is set| The LED displays the code 01 and enrollment finished. Light on fingerprint window turns off and the LED displays 0- ,continue to set other fingerprints

Notes:

1. If the buzzer makes two short beeps, and the red indicator light flashes, the setup fails
2. Each lock can only set 3 master fingerprints with code 00-02 , and the master fingerprints can delete each other, open the door, setup passage mode, as well as authorize and setup or delete the member fingerprints and spare password
3. After successful enrollment of the first master fingerprint, continue operation while the LED displays 0- to enroll other fingerprints needed; or else the LED will stop display two seconds later
4. When inputting fingerprint code, you can press Button to cancel current operation and re-input, or press Button during operation to exit setup state
5. Refer to Notes of Right method to apply fingerprint (Pg 02) for operation .

Enrollment of member fingerprints (take user 03 as an example)

Put the master finger that has been enrolled on the fingerprint window and enter door open state| Green light is on, and the LED displays the code of the master fingerprint
Press Button + to enter the enrollment mode| A beep sound heard, and the LED displays 0-
Press Button + or – to adjust the first digit 0 of the fingerprint code, and press Button # to confirm the choice| The figure just set jumps to the tens place, and the ones place displays 0
Continue to press Button + or – to adjust the second digit 1 of the fingerprint code, and press Button # to confirm| The LED displays the fingerprint code 03 and flashes alternately
Press Button # to reconfirm the fingerprint code 03| The LED displays fingerprint code 03 with the red light on the fingerprint window is on
Put the finger to be enrolled on the fingerprint collection window, and collect twice| When the red light of the fingerprint window is on, press with the finger; after the beep, remove the finger and press one more time. A long beep will sound and the two collections are successfully completed
Member fingerprint 03 is enrolled| Continue to set other fingerprints while the LED displays 0- ; or else the display will stop two seconds later, with green lights turn off.

Notes:

1. If the buzzer makes two short beeps, and the red indicator light flashes, the member fingerprint setup fails
2. After successful enrollment of a member fingerprint, continue operation while the LED displays 0- to enroll other fingerprints needed; or else the LED will stop display two seconds later;
3. The enrollment of the member fingerprints can only be completed under the authorization of the master fingerprin
4. The fingerprint codes are correspondent with the members. The above explanation takes the user with fingerprint code 03 as an example
5. When inputting fingerprint code, you can press Button to cancel current operation and re-input, or press Button during operation to exit setup state

Setup of spare password (code 99)

Operational procedure

• Put the master fingerprint on the fingerprint window and enter door open state
• Press Button + to enter the enrollment mode
• Press Button + or – to choose the first digit 9 of the password code, and press Button # to confirm the choice
• Continue to press Button + or – to adjust the second digit 9 of the password code, and press Button # to confirm
• Press Button # again to confirm the password code 99
• The password composes of 6 digits. Press Button + or – to choose the first digit of the password, and press Button # to confirm the choice
• Set other 5 digits following the above step , press Button # to enter each digit of the password.
• The spare password is set

Indication of the lock

• Green light is on, and the LED displays the code of the master fingerprint
• A beep sound heard, and the LED displays 0-
• The LED displays the figure 9 just set which jumps to the tens place, and the ones place displays 0
• The LED displays the fingerprint code 99 and flashes alternately
• The LED displays – 0 after a beep, both green and red indicator light on.
• The LED displays the figure selected after a beep, the figure jumps to the tens place, and the ones place displays 0
• Green light on and red light off after two long beeps, and the LED displays the last two digits of the password is set
• The LED displays 0- , the display will stop 5 seconds later, with green lights turn off.

Notes:

1. The original password of the new lock (factory setting) is 111111 , and this original password will be cleared at the time of the successfully enrollment of the master fingerprint
2. The spare password must be of 6 digits, which is an arbitrary combination of the figures 0~9
3. Only one spare password can be set for each lock, and with the code 99 . The spare password is the only password that can open the door, you can change it and delete it, please refer to P.15 for deletion of password
4. During the setting, the confirmed figure will be moved automatically to the tens place of the LED, with the figure to choose and confirm at the ones place

Deletion of fingerprints (take user 03 as an example)

Operational procedure

• Put the master finger that has been enrolled on the fingerprint window and enter door open state
• Press Button – to enter the deletion mode
• Press Button + or – to choose the first digit 0 of the password code, and press Button # to confirm the choice
• Continue to press Button + or – to adjust the seconddigit 3 of the fingerprint code,and press Button # to confirm
• Press Button # to reconfirm the fingerprint code to be deleted, and the deletion of the member fingerprint is completed

Indication of the lock

• Green light is on, and the LED displays the code of the master fingerprint
• The LED displays 0-
• The LED displays the figure 0 just set which jumps to the tens place, and the ones place displays 0
• The LED displays the fingerprint code 03 and flashes alternately.
• The light on the fingerprint window flash one time with a relatively sharp and quick beep, the LED displays 0- and stops display two seconds later

Notes:

1. Continue to input fingerprint code while the LED displays 0- , and repeat the operation for deletion of other fingerprint
2. The fingerprint codes 00-02 are master fingerprints, while 03-98 are member fingerprints
3. The deletion of the member fingerprint can only be completed when its fingerprint code is available

Deletion of password (Code 99 )

Operational procedure

• Put the master finger that has been enrolled on the fingerprint window and enter door open state
• Press Button – to enter the deletion mode
• Press Button + or – to choose the first digit 9 of the password code, and press Button # to confirm the choice
• Continue to press Button + or – to adjust the seconddigit 9 of the fingerprint code,and press Button # to confirm
• Press Button # to reconfirm the fingerprint code to be deleted, and the deletion of the member fingerprint is completed

Indication of the lock

• Green light is on, and the LED displays the code of the master fingerprint
• The LED displays 0-
• The LED displays the figure 9 just set which jumps to the tens place, and the ones place displays 0
• The LED displays the fingerprint code 99 and flashes alternately.
• The light on the fingerprint window flash one time with a relatively sharp and quick beep, the LED displays 0- and stops display two seconds later

Daily use state

Open the door with fingerprint

1. Start automatically
   Operational procedure

   • Put the finger enrolled on the fingerprint window, and the lock will activate automatically. Hold the finger for recognition, and enter the door open state

   • Turn the handle to open the door
     Indication of the lock

   • The green light is on, the LED displays the fingerprint code, and the electric engine makes a rolling sound

   • Otherwise it will automatically be locked 5 seconds later

2. Start manually
   Operational procedure

   • Press Button # to activate the lock

   • Put the finger enrolled on the fingerprint window, hold the finger for recognition, and enter the door open state

   • Turn the handle to open the door
     Indication of the lock

   • The green light is on, and the red light on the fingerprint window is on

   • The LED displays the fingerprint code, and the electric engine makes a rolling sound

   • Otherwise it will automatically be locked 5 seconds later

Open the door with password

Operational procedure

• Press Button + or – directly
• Input the 6-digit spare password. Press Button # to enter each digit of the password.
• Turn the handle to open the door

Indication of the lock

• The LED displays -0
• The green light is on all along after a beep, and the electric engine makes a rolling sound, with 99 display on the LED
• Otherwise it will automatically be locked 5 seconds later

Notes:

1. Method of password input: Press Button + or – to choose the first digit of the password, and press Button # to confirm the choice. Continue to choose other five digits with the same method
2. In case the automatically start function fails, press Button # to start it manually
3. If the operation fails, the red light will be on, and two short beeps sound

Setup passage mode

Press Button or # within 5 seconds after the door opened, and the passage mode is set

Note: Passage mode refers to the state in which the door can be opened immediately by turning the handle without recognition of fingerprint or password. It is for the convenience of conferences or gathering

Cancel passage mode

When the lock is in passage mode, place an enrolled fingerprint or input the valid password to cancel the passage mode

Use of emergency key

• Remove the screw with an instrument
  

• Remove the handle and you will see the key hole
  

• Insert the key and open the door
  

Use of external power

If it fails to operate the lock normally due to insufficient voltage, use a 9V battery for emergency power supply (pay attention to the positive and negative poles of the battery), and then place an enrolled fingerprint or input the spare password to open the door

Change of batteries

Procedure

• Remove the battery cover
• Remove all the used batteries
• Load new batteries
• Change of batteries completed

Notes:

1. When loading the batteries, operate correctly with attention to the sign of positive and negative poles in the battery box
2. When changing batteries, never mix the new battery with the used
3. Please preserve the environment by handing over the used batteries to designated place for reclaim

Trouble Shooting

Press the finger on the fingerprint collection window to open the door, red light is on together with two short beeps, and fails to open the door.|

1. This fingerprint might be illegal
2. This fingerprint has already been cleared

| Apply a valid fingerprint
Open the door with a valid fingerprint, red light is on with two short beeps, and fails to open the door.|

1. There is a large difference with the position of the valid fingerprint
2. The fingerprint is damaged

| Press the finger on the collection window again, trying tominimize the difference of the position

with that at the time of enrollment

Red light is constantly on|

1. Low battery voltage
2. PCB failure

|

1. Change the batteries
2. Check Cable connection

Alarm sounds when open the door| Low battery voltage| Change the batteries
No response after pressing the buttons| No battery| Change the batteries
Often fail to verify the fingerprints|

1. The finger is too dirty
2. The finger is too dry
3. The finger is too wet
4. The collection window is too dirty
5. The finger press on the collection window incorrectly

|

1. Clean the finger
2. Moisten the finger (e.g. touch the forehead with the finger)
3. Wipe the finger
4. Clean the collection window
5. Press the finger with the method on Page 2

Fail to enter the enrollment or deletion mode|

1. The finger for unlock is not the master finger
2. The operational procedure is incorrect

|

1. Confirm that you unlock with the master finger
2. Review the instructions or contact the BARSKA service department

After Sales Service

For questions or if you need assistance in using this product contact:

BARSKA
Customer Service Department
Tel. 888.666.6769
Fax. 909.445.8169
e-mail: service@barska.com
Monday-Friday 8:30AM-5:00 PM PST

1 YEAR LIMITED WARRANTY

BIOMETRIC SECURITY DOOR LOCK

BARSKA® Optics, as manufacturer, warrants this new precision optical product to be free of original defects in materials and/or workmanship for the length of time specified by this warranty. This warranty does not include damage caused by abuse, improper handling, installation, maintenance, normal wear- and-tear, unauthorized repairs  ormodifications and tampering in anyway.

This warranty is limited to the original purchaser and is not transferable. This warranty applies only to products purchased in the United States of America and Canada.

In the event of a defect within 30 days, the consumer must return the defective unit to the BARSKA dealer (the place of purchase) at his/her own expense.

Beyond 30 days, BARSKA products should be sent to the following address for warranty repairs. Products must be packed carefully and sturdily to prevent damage in transit, and returned freight prepaid to:

BARSKA® OPTICS
1721 WRIGHT AVE.
LA VERNE, CA 91750

For additional and updated information please visit our website at www.barska.com

Please email info@barska.com or call 1-888-666-6769 for Return Merchandise Number (RMA#) before any returns.
NOTE: All merchandise received without a valid RMA # will be returned to shipper at his/her own expense.

Please include all of the following when returning BARSKA products for service and/or replacement:

1. Please write your complete details (Name, Address, Telephone #, E-mail address, RMA#, etc.)
2. Purchase receipt or Proof of Purchase. (Original/Copy)
3. A brief explanation of the defect.
4. A Check/Money Order of $40.00 to cover inspection, shipping and handling.
   *Please allow 6-8 weeks for delivery

This product will either be replaced or repaired at the discretion of the warrantor. If it’s a discontinued item, we will replace the product with an equivalent product. Should the repair not be covered by this warranty, an estimate will be sent for your approval. Non-warranty repairs or refurbishing of your optical products are always provided at a reasonable cost.

BARSKA® Optics shall not be liable for any consequential, incidental and/or contingent damages whatsoever. This warranty supersedes all previous BARSKA® Optics warranties.

References

• Barska - Your Ultimate Source for Premium Safes and Outdoor Gear

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>