Spring Lighting Group SPL-FLL00X LED Magic Color Desktop Lights User Manual

Spring Lighting Group SPL-FLL00X LED Magic Color Desktop Lights

Installation diagram

Product List

Instructions for the receiving controller

You need to pay attention

•  Working temperature: -10~50℃
•  Input Volt.: 4.5~5.2V / ≥2A
•  Remote control distance: 10~20meters.
•  Remote control: Advanced RF / 2.4G technology

Instructions for Remote Control

The remote has 24 buttons

Note:

1.  Don’t set it arbitrarily, otherwise the corresponding color will be changed, such as red to blue
2.  If the remote control is out of control, please check if it is locked or check its battery.
3.  Remove the plastic film before use.

Instructions for use of led controller

los and android systems can download the APP by scanning the QR code. open the browser or other tools with “scan QR code” funnction,scan the QR code as below: Use your phone to scan the QR code

APP Installation steps
Click DuoCol StripX on the APP iconenter the app page. After entering the App interface,if bluetooth is not enabled,an application wants to enable the bluetooth function of this device click allow

1.  Connect the lamp to power.
2.  Turn on the Bluetooth funcon of the mobile phone, scan the code on the receiver Box, download the APP of the mobile phone, or use the remote control to operate directly.
3.  The product uses USB cable 5V/2A, can connect any USB port power supply, convenient, stable and safe.

Note:

1.  Check if the power supply is normal.
2.  Check if the Bluetooth is turned on.
3.  Check if there are other mobile phones are connected, only support connections one to many, dose not support many to many.
4. Check APP Bluetooth setting if the phone is connected to the device, if connect, exit the APP and reopen, the APP will go to connect automatically.
5. Normal operations and can not connect, please exit the APP and reopen.
6. Exit APP, restart the mobile phone, power on the strip light, reopen the APP, then them will connect automatically.

App Instructions

1.  Enter the mobile APP interface and open the upper right corner Settings to view Guide. You’ll have all the instructions here.
2. Please do not change the “Modify Pin Sequence”, Otherwise will change the corresponding color. For example: choosing blue shows red.

Click to show the lamp list,view lamp list:

Switch to color and brightness interface

Switch to the mode interface

Switch to the music rhythm interface

Switch to the microphone rhythm interface

Switch to the timing interface

Switch to the setting interface

Do not change the settings at will if you change it, it will affect the normal use of the product:

1.  The color should not match the remote control.
2.  The change of the number of points will affect the dynamic effect of the light. If you have any querstion after receiving

Thank you for buying this product. To Provide an excellent user experience, please install it according to these instructions and then give the instructions to appropriate person for rerention and future referece.

FCC Statment

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

•  Reorient or relocate the receiving antenna.
•  Increase the separation between the equipment and receiver.
•  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•  Consult the dealer or an experienced radio/TV technician for help.

Warning : changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment The devices has been evaluated to meet general RF exposure requirement， the device can be used in portable exposure condition without estriction

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>