fisher-price HBM25 Fitness Fun Folding Jumperoo Activity Center User Guide

fisher-price HBM25 Fitness Fun Folding Jumperoo Activity Center

Product Information

• Product Name: HBM25 Assembly
• Time: Approximately 20 minutes
• Battery Requirement: Three AA (LR6) x 1.5v alkaline batteries (not included)
• Battery Installation Tool: Phillips screwdriver (not included) Recommended
• Battery Type: Alkaline batteries for longer life Language
• Options: Replacement warning labels available for non-English languages

Product Usage Instructions

1. Inspect the product before assembly and each use. Check for damaged hardware, loose joints, missing parts, or sharp edges. Do not use the product if any parts are missing, damaged, or broken. Only use accessories and replacement parts approved by the manufacturer.
2. Adult assembly is required. No tools are needed for assembly. Set aside at least 20 minutes for assembly.
3. If the product comes with an electronic toy, consider installing the batteries before assembly. Refer to the Battery Installation section.
4. Loosen the screw in the battery compartment door using a Phillips screwdriver and remove the door. Insert three AA (LR6) alkaline batteries into the compartment. Replace the door and tighten the screw. If the electronic toy operates erratically, reset the electronics by sliding the power/volume switch off and then back on. Replace the batteries when the sounds or lights become faint or stop.
5. Begin the assembly process by positioning the seat pad with the red tabs facing you and the seat ring with the instructional labels facing you.
6. Align the red tabs on the seat pad with the pegs below each instructional label on the seat ring. Snap the tabs to the pegs.
7. Snap the tabs on the side of the pad to the matching pegs on the seat ring.
8. Turn the seat ring around so that the front faces you.
9. Snap the remaining four tabs on the seat pad to the pegs on the seat ring.
10. Adjust the seat height before placing your child in the seat. The product is shipped with the straps in the middle height position. Check the distance between your baby’s feet and the floor. The child’s toes should touch the floor without bouncing. If the entire foot is touching the floor or the toes are not touching the floor at all, adjust the height to one of the three positions available (one for the smallest child and three for the tallest child).

BEFORE YOU BEGIN

IMPORTANT!

• Keep instructions for future use.

• Read all instructions before assembly and use of the product.

• Before assembly and each use, inspect this product for damaged hardware, loose joints, missing parts or sharp edges. Do not use the product if any parts are missing, damaged or broken. Do not use accessories or replacement parts other than those approved by the manufacturer. Never substitute parts.

• Adult assembly is required. No tools needed for assembly.
  Product features and decorations may vary from images.

• Set aside at least 20 minutes for assembly.

• Three AA (LR6) x 1,5 v alkaline batteries are required (not included).
  Tool needed for battery installation: Phillips screwdriver (not included).
  For longer life, use alkaline batteries.

• This product may come with replacement warning labels which you can apply over the factory-applied warning label if English is not your primary language. Select the warning label with the appropriate language for you.

WARNING

FALL HAZARD
Babies can FALL from product resulting in head injuries.

• NEVER leave child unattended. Always keep child in view while in product.
• NEVER use near stairs.
• To avoid tip over, place product on a flat, level surface.

STRANGULATION HAZARD
Strings can cause STRANGULATION.

• DO NOT place items with a string around child’s neck, such as hood strings or pacifier cords.
• DO NOT suspend strings over product or attach strings to toys.
• Use only for a child who is able to hold head upright unassisted and who is not able to walk or climb out of product.

PARTS

IMPORTANT! Please remove all parts from the package and identify them before assembly. Some parts may be packed in the pad.

PARTS

BATTERY INSTALLATION

• Loosen the screw in the battery compartment door with a Phillips screwdriver and remove the battery compartment door.
• Insert three AA (LR6) alkaline batteries into the battery compartment.
• Replace the battery compartment door and tighten the screw.
• If the electronic toy product begins to operate erratically, you may need to reset the electronics. Slide the power/volume switch off and then back on.
• When sounds or lights become faint or stop, it’s time for an adult to replace batteries.

Battery Safety Information

• In exceptional circumstances, batteries may leak fluids that can cause a chemical burn injury or ruin your product. To avoid battery leakage:
• Do not mix old and new batteries or batteries of different types: alkaline, standard (carbon-zinc) or rechargeable.
• Insert batteries as indicated inside the battery compartment (+ and -).
• Remove batteries during long periods of non-use. Always remove exhausted batteries from the product. Dispose of batteries safely. Do not dispose of this product in a fire. The batteries inside may explode or leak.
• Never short-circuit the battery terminals.
• Use only batteries of the same or equivalent type, as recommended.
• Do not charge non-rechargeable batteries.
• Remove rechargeable batteries from the product before charging.
• If removable, rechargeable batteries are used, they are only to be charged under adult supervision.

ASSEMBLY

ASSEMBLY

• Position the seat pad with the red tabs toward you and the seat ring with the instructional labels toward you.
• Align the red tabs on the seat pad to the pegs below each instructional label on the seat ring. “Snap” the tabs to the pegs.
• “Snap” tabs on the side of the pad to the matching pegs.
• Turn the seat ring around so that the front faces you.
  “Snap” the remaining four tabs on the seat pad to the pegs on the seat ring.

SEAT HEIGHT ADJUSTMENT

IMPORTANT! This product is shipped with the straps in the middle height position . Please be sure you adjust the height of the frame for your child.

• • Place your child in the seat. Check the distance between your baby’s feet and the floor. Your child’s toes should touch the floor (without bouncing). If your child’s entire foot is touching the floor or the toes are not touching the floor at all, adjust the height to any of three positions (one for the smallest child and three for the tallest child).

• While feeding the strap into the slot on the inside of the hub, pull the strap on the outside of the hub. Lower the strap bar.

• Pull the strap out or feed it into the hub to the desired height 1,2,3 .

• Separate the layers of webbing and fit the strap bar into the desired slot in the strap.
  Hint: You may need to feed the strap, from the inside of the hub, to be able to insert the strap bar into the slot in the strap.

• Lift the strap bar to secure the strap in place.
  Repeat this process to adjust the height for the other two straps.
  IMPORTANT! Make sure all three straps are adjusted to the same height.

JUMP ON IN & EXPLORE AROUND WITH MUSIC, LIGHTS, AND SOUNDS!

CARE

The pad is machine washable. Wash it separately in cold water on the gentle cycle. Do not use bleach. Tumble dry separately on low heat and remove promptly.
The frame, seat ring and toys may be wiped clean using a mild cleaning solution and damp cloth. Do not use bleach. Do not use harsh or abrasive cleaners. Rinse clean with water to remove soap residue. Do not immerse the electronic toy.

Remove the Seat and Pad
Lift the frame. While pressing a tab on the seat, pull the seat from the frame. Replace the Seat and Pad
Please follow the Assembly instructions.

STORAGE

Press the frame release button.
Lift the base tube.

FCC STATEMENT

(UNITED STATES ONLY)

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Consult the dealer or an experienced radio/TV technician for help.

NOTE: Changes or modifications not expressly approved by the manufacturer responsible for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Protect the environment by not disposing of this product or any batteries with household waste. This symbol indicates that this product shall not be treated as household waste. Check your local authority for recycling advice and facilities.

UNITED STATES
Fisher-Price, Inc., 636 Girard Avenue, East Aurora, NY 14052. Consumer Services: 1-800-432-5437.

CHILE
Mattel Chile, S.A., Avenida Américo Vespucio 501-B, Quilicura, Santiago. Tel.: 1230-020-6213.

©2021 Mattel. PRINTED IN CHINA

HBM25-2C70
1102718823-2LC

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>