Pxwaxpy 204LED Outdoor Solar Lamp with Motion Sensor User Manual

Pxwaxpy 204LED Outdoor Solar Lamp with Motion Sensor

Product Information

• Product Name : Solar Motion-activated Light
• Dimensions
  • Length : 107.00 mm
  • Width : 107.00 mm
  • Height : 80.00 mm
• Features
  • Motion-activated : The light automatically turns on dim light at night and switches to high light whenever motion is detected. It  turns back to dim light 20 seconds after motion stops.
  • Dusk to Dawn : The light automatically turns on at night and turns off during the daytime or when the battery is powered off. This mode does not have motion sensing function.

Product Usage Instructions

Solar Light Location
For optimum light duration throughout the night, it is important to place the solar panel in a spot where it can receive the maximum amount of direct sunlight throughout the day. Make sure to charge the solar light for two sunny days initially to fully charge the battery.

Lighting Modes

• Motion-activated High Light : Press the switch and the light flashes one time. The light turns on high light whenever motion is detected and automatically shuts off 20 seconds after motion stops to prolong battery life.
• Dusk to Dawn : Press the switch and the light flashes three times. The light automatically turns on at night until in the daytime or the battery is powered off. This mode does not have motion sensing function.

Installation

Step 1: Installing the Mounting Plate (Light Fixture)
Ensure the light fixture and the solar panel are located less than 5 meters apart for the cord to reach. Follow these steps

1. Place the mounting plate (C) against the mounting surface and mark the two holes for the screws on the wall.
2. Use a power drill to drill two holes into the mounting surface.
3. Insert the wall anchors (BB) and attach the mounting plate (C) using the two mounting screws (AA).

Step 2: Mounting the Light Fixture
Slide the rotation axle of the light fixture down onto the mounting plate (C) until it snaps into place. Before mounting the light, press the light switch located at the back of the lamp to set the lighting mode.

Step 3: Installing the Mounting Plate (Solar Panel)
Follow these steps

1. Place the mounting plate (C) against the mounting surface and mark the two holes for the screws on the wall.
2. Use a power drill to drill two holes into the mounting surface.
3. Insert the wall anchors (BB) and attach the mounting plate (C) using the two mounting screws (AA).

Step 4: Mounting the Solar Panel
Slide the rotation axle onto the mounting plate (C) until it snaps into place. Rotate the solar panel (B) to the desired angle. Make sure the solar panel is aimed toward the sun with minimal obstructions. If possible, mount the panel facing toward the southern sky.

Step 5: Connecting the Solar Panel to the Light Fixture
Carefully route the solar panel cable to the light fixture. Insert the end of the solar panel cable (1) into the light fixture cable (2).

Charging the Battery
For optimum performance, it is best to install the solar light in full sunlight and let it charge for 8 hours. Allow the light to run at least 8-12 entire charging and discharging cycles to reach the maximum capacity of the battery.

Solar Motion-activated

USER MANUAL

Solar Light Location
For optimum light duration throughout the night, it is very important to place the solar panel in a spot where it can receive the maximum amount of direct sunlight throughout the day.

NOTE: In some cases, the power of battery would come empty out of the box. Let the solar light charge for two
sunny days for the battery to get fully charged.

CONSTRUCTION

LIGHTING MODE

1. Motion-activated High Light
   • (Press the switch and the light flashes one time.)
   • The light turns on high light whenever motion is detected. It automatically shuts off 20 seconds after motion stops to prolong battery life.
2. Dim light + Motion-activated High Light
   • (Press the switch and the light flashes two times.)
   • The light automatically turns on dim light at night and turns to high light whenever motion is detected. The light turns to dim light 20 seconds after motion stops.
3. Dusk to Dawn
   • (Press the switch and the light flashes three times.)
   • The light automatically turns on at night until in the daytime or the battery is power off. There is no motion sensing function in this mode.

PACKAGE INCLUDED

INSTALLATION

• Step1: Installing the mounting plate（Light Fixture）
  • NOTE: Ensure the light fixture and the solar panel are located less than 5 meters for the cord to reach.
  • Place the mounting plate (C) against the mounting surface and mark the two holes for the screws on the wall. Use power drill to drill two holes into the mounting surface. Insert the wall anchors (BB) and attach the mounting plate (C) using the two mounting screws (AA).
• Step 2 : Mounting the light fixture
  • Slide the rotation axle ⑤ of the light fixture down onto the mounting plate (C) until it snaps into place.
  • NOTE : Press the light switch located at the back of the lamp to set the lighting mode before mount the light.
• Step 3 : Installing the mounting plate (Solar Panel) Place the mounting plate (C) against the mounting surface and mark the two holes  for the screws on the wall. Use power drill to drill two holes into the mounting  surface. Insert the wall anchors (BB) and attach the mounting plate (C) using the two mounting screws (AA).
• Step 4 : Mounting the solar Panel
  • Slide the rotation axle ⑤ onto the mounting plate (C) until it snaps into place. Rotate the solar panel (B) to the desired angle.
  • NOTE : Make sure the solar panel is aimed toward the sun with a minimum amount of obstructions. If possible, mount the panel facing toward the southern sky.
• Step 5 : Connecting the solar panel to the light fixture Carefully route the solar panel cable to the light fixture. Insert the end of the solar panel cable (1) into the light fixture cable (2).
• CHARGING THE BATTERY ： For optimum performance, it is best to install the solar light in full sunlight and let it charge for 8 hours. Allow the light to run at least 8-12 entire charging and discharging cycles to reach the maximum capacity of the battery.
• WINTER TIPS : F or optimal performance, be sure to remove any snow or debris accumulation from solar panel. If solar panel have been covered by snow for a long time, allow the battery to recharge in full, direct sunlight for at least 10-12 hours so it can maintain maximum capacity.

NOTE: The performance of the solar lamp will vary with the time of year. It will deliver more light when it has had a full day in the sun rather than a day in overcast weather.

TROUBLE SHOOTING

WARNING: Please keep out of reach of children. Do not dispose of Li-Ion battery in the regular trash, municipal waste stream or by fire as batteries may leak or explode. Do not open, short circuit, or mutilate batteries as injury may occur. Preserve our environment by recycling Li-Ion batteries or disposing of them in accordance with local, state and federal regulations. Do not mix old and new batteries.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>