Liene M200 Instant Photo Printer User Manual

Liene M200 Instant Photo Printer

User Manual for Amber M200 Instant Photo PrinterPlease read this Manual carefully before using the product and keep it properly

Product Overview

• Power Button
• Indicators:
  • Power Indicator
  • Battery Indicator
  • Failure Indicator
  • Wi-Fi Hotspot Indicator
• Air Vent
• Paper Ejection Slot
• Type-C USB Port (Not for charging, data only)
• Side Door
• Front Door
• Reset Hole
• Power Socket

Accessory List

• Power Adapter x1
• Paper Cassette Holder
• Paper Cassette Cover
• Paper Cassette x1
• Photo Paper 20 sheets x1
• Ink Cartridge x1

Install Ink Cartridge

1. Insert new ink cartridge until the lock is in place
2. Close the side door

Refill Photo Paper

1. Open the paper cassette cover along the top seam
2. Load photo paper in the cassette with the glossy side face-up
   • Note:
   1. The maximum of the cassette is 20 sheets of photo papers.
   2. Do not touch the area within the crop marks of a photo paper.
   3. Undrawing the paper cassette holder makes refilling easy.
3. Close the paper cassette cover

Install Paper Cassette

1. Undraw the paper cassette holder
2. Insert the paper cassette into the printer

Replace Ink Cartridge

1. Lift the lock upward to pop out used ink cartridge and take it out
2. Insert new ink cartridge until the lock is in place, then close the side door

Usage

• Working Location:
  • When printing, the photo paper goes back and forth. Please make sure to leave more than 4 inches (10 cm) space behind the printer.
  • Note: Paper goes in and out for 4 times.
• Storage:
  • When the printer is not in use, place the paper cassette on top of the printer for space saving and easy storage.
  • The printer has a built-in lithium battery, avoid keeping it in high temperature and high humidity environment.
  • Charge at least once every 3 months.
  • Do not use after immersion in water.

Instruction for Buttons

• Press and hold Power Button for 1 second to power on.
• Quickly press Power Button to power off.
• Press Power Button 3 times to reset printer Wi-Fi hotspot password.
• Quickly press Power Button 6 times to restore factory settings.

Note:

1. All indicators light on and blink for 2 seconds simultaneously if the factory settings are restored successfully.
2. Wi-Fi hotspot indicator blinks for 2 seconds if the printer Wi-Fi hotspot password is reset successfully. Reset the network only when printer is idle or there is a printer failure. Default password is 12345678.
3. During printing, printing will not be interrupted when the power button is pressed.
4. During firmware upgrading, upgrading will not be interrupted when the power button is pressed.
5. When there is a failure, press the power button to power the printer off. Then, power the printer on again. The printer will try to fix the problem automatically after powering on. If fail to power the printer off, please use a pin to poke the reset hole at the back of the printer to restart.

Indicators:

• Power Indicator:
  • Light off: Power off
  • Light on: Power on
  • White light blink: Printing or Firmware upgrading
  • Breath: In sleep mode
• Failure Indicator:
  • Light off: No failure
  • Orange light blink: Failure
• Battery Indicator:
  • Light off: Battery off
  • Orange light on: Battery charging
  • White light on: Battery fully charged
  • White light blink: Low battery
  • Orange light blink: Battery error

Please read this Manual carefully before using the product and keep it properly

Product Overview

Accessory List

Install Ink Cartridge

1. Open the side door
2. Insert new ink cartridge until the lock is in place
3. Close the side door

Refill Photo Paper

1. Open the paper cassette cover along the top seam

2. Load photo paper in the cassette with the glossy side face-up
   Note:

3. The maximum of the cassette is 20 sheets of photo papers.

4. Do not touch the area within the crop marks of a photo paper.

5. Undrawing the paper cassette holder makes refilling easy.

6. Close the paper cassette cover

Install Paper Cassette

1. Undraw the paper cassette holder
2. Rotate the holder down 180° to the bottom
3. Insert the paper cassette into the printer

Replace Ink Cartridge

1. Open the side door
2. Lift the lock upward to pop out used ink cartridge and take it out
3. Insert new ink cartridge until the lock is in place, then close the side door

Usage

Working Location
When printing, the photo paper goes back and forth. Please make sure to leave more than 4inchs (10cm) space behind the printer.

Note: Paper goes in and out for 4 times.

Storage
When the printer is not in use, place the paper cassette on top of the printer for space saving and easy storage.
The printer has a built-in lithium battery, avoid keeping in high temperature and high humidity environment. Charge at least once every 3 months. Do not use after immersion in water.

Instruction for Buttons

Note:

1. All indicators light on and blink for 2 seconds simultaneously if the factory settings are restored successfully.
2. Wi-Fi hotspot indicator blinks for 2 seconds if the printer Wi-Fi hotspot password is reset successfully. Reset the network only when printer is idle or there is a printer failure. Default password is 12345678.
3. During printing, printing will not be interrupted when the power button is pressed.
4. During firmware upgrading, upgrading will not be interrupted when the power button is pressed.
5. When there is a failure, press the power button to power the printer off.
   Then, power the printer on again. The printer will try to fix the problem automatically after powering on. If fail to power the printer off, please use a pin to poke the reset hole at the back of the printer to restart.

Power Indicator

Note:

• Sleep mode starts after idle for 5 minutes. Press Power Button or send a print job to wake the printer up.
• Auto-power off after idle for 20 minutes.

Failure Indicator

Battery Indicator

Wi-Fi Hotspot Indicator

1. Connect Power Supply
   Plug the power jack into the power socket at the back of the printer.

2. Power On

   • Press the power button to power the printer on.
   • Power indicator lights on in white, Wi-Fi hotspot indicator starts blinking in orange in about 10s, then lights on in orange.
   • The printer enters the idle status.

3. Connect Device Wi-Fi

4. Open the WLAN connection on your smartphone, tablet, computer, etc. and select “Liene Photo Printer [xxxx]”.

5. The default connection password is 12345678.

6. When the Wi-Fi hotspot indicator lights on in blue, it means successful connection for at least 1 device.

Note:

1. You can change the password in the APP.
2. Support to connect to a maximum of 5 devices simultaneously.
3. [xxxx] refers to the last four digits of the product SN number, which can be found on the label at the bottom of the printer.
4. For Android device, after switching the Wi-Fi signal to the printer Wi-Fi hotspot signal, it will pop up a message that the internet may not be available.
5. Please keep the WLAN connection when using the printer.
6. Please download and install the computer driver before connecting to a computer.

How to print

1. Print with “Liene Photo” APP
   Search for “Liene Photo” in the App Store or scan the QR code below to download and install the “Liene Photo” App.
   Open “Liene Photo” App and follow the APP prompts to add a device. You can find the device in the list on the home page after it is successfully added.
   Note: The actual operation may not match the description here due to “Liene Photo” APP upgrades and updates.
   Please follow the instructions within the current “Liene Photo” APP to operate.
   Make sure that the device is connected to the printer Wi-Fi hotspot, and the Wi-Fi hotspot indicator lights on in blue.
   Follow the operation prompts in the APP to print.

2. Print from Android Device
   Make sure that the device is connected to the printer Wi-Fi hotspot, and the Wi-Fi hotspot indicator lights on in blue.
   Confirm that you agree to use this network.
   Open the album and select the photos, then select the printer,adjust the printing parameters and print. If the printer is not found, please turn on “Default Print Service”.
   If the printing interface is not found in the phone album, go to https://mopria.org/print-from-android to download the APP and see how to use it.

3. Print from iOS Device
   Make sure that the device is connected to the printer Wi-Fi hotspot, and the Wi-Fi hotspot indicator lights on in blue.
   Confirm that you agree to use this network.
   Open the album and select the photos, then select the printer,adjust the printing parameters and print.
   Note: USB printing is supported for Mac computers.

4. Print via USB from a computer
   Go to https://global.liene-life.com/pages/download to download the driver for Photo Printer Series and install it.
   Connect the printer to the computer using a USB cable. Select the photos, click “Print”, and select “Liene Photo Printer”.

5. Print via Wi-Fi from a computer
   Go to https://global.liene-life.com/pages/download to download the driver for Liene Photo Printer Series and install it.
   After the computer has successfully connected to the printer Wi-Fi hotspot, follow the steps in the table below to set the printer connection.
   After successful connection, select the photos, click “Print”, and select “Liene Photo Printer[xxxx]-Wi-Fi”.

Note: Please make sure that the computer is connected to the printer Wi- Fi hotspot. [xxxx] refers to the last four digits of product SN number, which can be found on the label at the bottom of printer.

Troubleshooting

The Liene app will alert you to various error conditions through in-app messaging. Follow the app instructions to resolve issues.
For additional help on specific issues with your Liene photo printer, see the FAQs on global.liene-life.com

Warranty & Support

Thank you for choosing Liene! We really hope you will enjoy the product! Your satisfaction means everything to us!
Liene provides a 1-year warranty for this product, please contact us immediately if you encounter any of the following, and we will supply a replacement or refund.

1. Receiving defective items;
2. Short packaging;
3. Parts are broken in transit;
4. Item stops working within warranty;
5. Wrong order.

To provide more prompt and professional after-sale service, you may contact us via below ways
E-mail: liene.service@hannto.com
Phone: +1 (833) 755 2014

Caution & Notice

• Use only official power adapter for use with the product.
• Do not use the original adapter for other devices to avoid damage.
• Do not plugin or unplug the product with wet hands.
• Do not damage, break or modify the power cord.
• Do not charge battery at temperatures outside the range of 5°C~40°C(41°F-104°F). This may cause electric shock, explosion or fire.
• Do not use after immersion in water.
• Do not touch the glossy side of a photo paper to avoid leaving fingerprints and affecting printing quality.
• Do not handle paper with wet hands and keep paper free of dust.
• Do not Write on paper before printing.
• Do not use unofficial ribbon and photo paper.
• Never reuse paper for printing, even if most of the paper is blank. Reusing paper may damage the printer if paper jams or the ink sheet adheres to the paper.
• Do not load paper upside-down, make sure the glossy side of a photo paper is facing up. the photo paper is laid flat in the paper cassette, and the paper cassette is properly installed on the front of the printer.
• Do not block the rear of printer.
• Do not get the product wet. Do not insert foreign objects or liquids into the product.
• The optimal working temperature for the printer is 10°C~35°C (50°F~95°F), and the relative humidity is 40%-60%. Printing quality maybe affected if the environmental temperature and humidity are not appropriate.
• During printing, a photo paper needs to go through the printer four times and will be pushed out automatically when the printing is finished. Do not pull out the photo paper forcibly to avoid damage to the printer.
• Do not touch any parts inside product, it may case injury.
• It is normal to have slightly different printing colors between different printers.
• When the printer is not in use for a long time, remove the paper cassette and close paper cassette cover the to prevent dust and debris from entering the paper path. Otherwise, the printing quality of first photo next time you print will be affected.
• When keeping the unused photo paper in the printer, avoid to store it in a hot and humid environment.
• The printer has a built-in lithium battery, avoid keeping in high temperature and high humidity environment. Charge at least once every 3 months if not connecting to the power supply.
• Plug in the power adapter during upgrading to avoid damage to the printer due to power failure caused by low battery.
• Under normal use of condition, this equipment should be kept a separation distance of at least 20 cm between the antenna and the body of the user.

FCC Statement

The United States Federal Communications Commission (in 47 CFR 15.105) has specified that the following notice be brought to the attention of users of this product.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help

FCC Radiation Exposure Statement
This device complies with FCC radiation exposure limits set forth for an uncontrolled environment.This equipment must be installed and operated in accordance with provided instructions and theantenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons.

Caution!
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Regulatory Compliance Information
Hereby, Hannto Technology Co., Ltd. declares that the radio equipment type DHP512 & DHP513 is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: https://global.liene-life.com/pages/Service/declaration.html
All products bearing this symbol are waste electrical and electronic equipment (WEEE as in directive 2012/19/EU) which should not be mixed with unsorted household waste. Instead, you should protect human health and the environment by handing over your waste equipment to a designated collection point for the recycling of waste electrical and electronic equipment, appointed by the government or local authorities. Correct disposal and recycling will help prevent potential negative consequences to the environment and human health.
Please contact the installer or local authorities for more information about the location as well as terms and conditions of such collection points.

• The operation temperature range of the battery is 5 °C~40 °C.
• Replacement of a battery with an incorrect type that can defeat a safeguard (for example, in the case of some lithium battery types);
• Disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, that can result in an explosion;
• Leaving a battery in an extremely high temperature surrounding environment that can result in an explosion or the leakage of flammable liquid or gas;
• A battery subjected to extremely low air pressure that may result in an explosion or the leakage of flammable liquid or gas.

Note: The illustrations of products, accessories and user interface in this Manual are indicative and for reference only. The actual product may slightly differ due to product updates and upgrades.

Amber M200 Instant Photo Printer

• Product Name: Photo Printer

• Product Model: DHP512

• Rated Input: 24V 1.6A

• Power Consumption 60W (printing max)
  1.07W (sleep mode)

• Battery Capacity: 24.84Wh 10.8V 2300mAh

• FCC ID: 2AZHDDHP513

• Product Size: 205×124.6 ×85.4mm

• Product Net Weight: ~1.4kg

• Operation Temperature: 10°C~35°C

• Wireless Connectivity: IEEE 802.11 b/g/n 2.4GHz

• Maximum Output Power: 18 dBm

• Working Frequency: 2400 – 2483.5 MHz

Manufacturer: Hannto Technology Co., Ltd.

Address: Room 704, Building 1, No.88, Shengrong Road, Pudong, Shanghai,China
For further information, please go to https://global.liene-life.com

References

• Liene Photo Printers | Liene-life
• Driver Download | Liene-life.com
• Liene Photo Printers | Liene-life
• Liene Photo Printers | Liene-life
• Driver Download | Liene-life.com
• EU Declaration OF Conformity | Liene-life
• Print From Android

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>