ZZIPP ZZONE1000D Power Amplifier User Manual
- June 15, 2024
- ZZiPP
Table of Contents
ZZIPP ZZONE1000D Power Amplifier User Manual
Thanks for purchasing this ZZIPP product, please read this instruction carefully to understand how to operate the product correctly. Please store this instruction in a safe place after reading as a reference in the future.
SAFETY INSTRUCTIONS
To reduce the risk of electric shock, do not remove the cover or the side. Always contact qualified personnel for repairs.
CAUTION
RISK OF ELECTRIC SHOCK! DO NOT OPEN!
ATTENTION
RISQUE DE CHOC ELECTRIQUE! NE PAS OUVRIR!
To reduce the risk of fire and electric shock, do not expose the appliance to
moisture and direct contact with liquids. To avoid the risk of fire or shock,
do not expose the product to rain or direct and excessive humidity. If the
environment is much colder than the temperature of this product, wait for it
to adjust to the ambient temperature before turning it on. Connect the product
only to grounded and protected circuits. Always unplug it from the power
source before cleaning or replacing the fuse. Replace the fuse with one of the
same type and rated voltage. Do not clean the product with solvents or
aggressive cleaners. Use a soft, clean cloth. Before connecting the product to
the power supply, make sure that the power cable is not damaged.
Make sure that the voltage of the electrical outlet is within the range indicated on the product (on the case or on a sticker). Never unplug the product from the outlet by pulling on the cord. Always ensure that the product is used in a well ventilated location with at least 50cm clearance from adjacent surfaces. Make sure that none of the ventilation openings are blocked. Do not use the product in temperatures above 104°F / 40°C. Keep flammable materials away from the product during use.
If you experience serious problems while using the product, stop using it immediately. Do not open the product housing. Contains parts that cannot be repaired by the user and opening it will void the warranty
FRONT PANEL
- POWER SWITCH Device power button
- POWER INDICATOR LED indicator that lights up when the device is in operation
- SIGNAL INDICATOR LED indicator of safe operating range
- CLIP INDICATOR LED indicator of the distortion status of the amplifier input signal. To make the amplifier work in the safe state, lower the input gain level. Attention! the amplifier does not make any correction to the distorted signal.
- PROTECTION INDICATOR Protection status LED indicator. Turn off the amplifier and check the causes. The amplifier is protected against over temperature, overload, short circuit and DC.
- OLED DISPLAY Displays the status of the DSP and set parameters.
- CHANNEL VOLUME CONTROL Adjust the volume of the channel CH1, CH2.
- MENU ENTER ENCODER Short press the encoder to display the DSP mode and version. Long press the encoder for 2 seconds to enter the DSP internal setting parameters.
- PC IN Use the USB cable to connect to the computer and open the software to adjust the DSP parameters.
REAR PANEL
- AC CORD Plug this cord into the power supply socket. Before using a power amplifier, check if the input voltage accordance with the machine voltage.
- FUSE Protect your amplifier from AC problems. If the power amplifier is “on” and nothing lights, please verify the fuse compartment. If fuse is broken, please read it and change with a new one of same size and value.
- INPUT CONNECTOR XLR balanced input
- PARALLEL / OUTPUT CONNECTORS XLR balanced output, use this output to connect to another amplifier system.
- NL4MP CONNECTORS OUTPUT Speakers stereo connection 1+, 1-, bridge connection CH1 + 2. Note: this product design minimum output impedance 4Ω, please don’t drive nominal less than 4Ω loudspeaker loads, this may cause amplifier don’t work properly or overheating.
- WAY BINDING POST CONNECTORS Output connection speaker.
- COOLING FAN Turn on the power to the amplifier, the cooling fun runs in dust removal mode at highspeed for 3 seconds, then enters idle speed, as the operating temperature rises the cooling fan speed becomes higher.
MODE SWITCH STEREO
MODE SWITCH PARALLEL
MODE SWITCH BRIDGE
XLR PINOUT
Balanced Circuit
**Unbalanced Circuit
**
NL4MP SPEAKER CONNECTORS
NL4MP SPEAKON WIRING
BINDING POST CONNECTORS
STEREO/ PARALLEL
BRIDE
TECHNICAL SPECIFICATIONS
| MODEL | ZZONE600D | ZZONE800D |
|---|---|---|
| SYSTEM | Stereo power amplifier | Stereo power amplifier |
| POWER 8Ω | 600W | 800W |
| POWER 4Ω | 920W | 1300W |
| SPEAKER OUTPUT | Operation up to 2Ω | |
| INPUTS | Channels 1-2 (L-R) | Channels 1-2 (L-R) |
| FREQUENCY RESPONSE | 20Hz – 20KHz | 20Hz – 20KHz |
| POWER SUPPLY | AC230V, 50-60Hz | AC230V, 50-60Hz |
| CONTROLS | Signal / Overload / Clip | |
| DIMENSIONS | 483 x 88 x 420mm | 483 x 88 x 420mm |
| WEIGHT | 8.9Kg | 9.6Kg |
| MODEL | ZZONE1000D | ZZONE1500D | ZZONE4600D |
|---|---|---|---|
| SYSTEM | Stereo power amplifier | Stereo power amplifier | 4CH power |
amplifier
POWER 8Ω| 600W| 800W| 4 x 400W
POWER 4Ω| 920W| 1300W| 4 x 650W
SPEAKER OUTPUT| Operation up to 2Ω
INPUTS| Channels 1-2 (L-R)| Channels 1-2 (L-R)| Channels 1-2 (L-R)
DSP| Built in DSP| Built in DSP| Built in DSP
FREQUENCY RESPONSE| 20Hz – 20KHz| 20Hz – 20KHz| 20Hz – 20KHz
POWER SUPPLY| AC230V, 50-60Hz| AC230V, 50-60Hz| AC230V, 50-60Hz
CONTROLS| Signal / Overload / Clip
DIMENSIONS| 483 x 88 x 420mm| 483 x 88 x 420mm| 483 x 88 x 420mm
WEIGHT| 8.9Kg| 9.6Kg| 10Kg
Imported and distribuited by:
ZZIPP Group S.p.A.
Via Caldevigo 23/d, 35042 Este (PD)
0429 617 888
info@zzippgroup.com
zzippgroup.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>