ZZiPP ZZSPARCOLDM Cold Spark Fountain Effect User Manual
- June 9, 2024
- ZZiPP
Table of Contents
ZZiPP ZZSPARCOLDM Cold Spark Fountain Effect User Manual
Thanks for purchasing this ZZIPP product, please read this instruction carefully to understand how to operate the product correctly. Please store this instruction in a safe place after reading as a reference in the future.
SAFETY INSTRUCTIONS
To reduce the risk of electric shock, do not remove the cover or the side.
Always contact qualified personnel for repairs.
To reduce the risk of fire and electric shock, do not expose the appliance to moisture and direct contact with liquids.
The machines are designed for an intermittent effect, the maximum duration of
the single effect is 30 seconds, and a good rule of thumb to avoid overheating
the machine to allow time to pass between one effect and the next.
Protect your eyes when operating the machine.
Machine subjected to dangerous voltage, risk of injury from electric shock. Under no circumstances should you attempt to open the machine or to remove or adjust the components mounted inside it.
Contact qualified personnel for maintenance. Keep the machine and controller dry and do not use outdoors on rainy or snowy days. Do not introduce anything into the machine other than the powder for the effect. Check the installation in order to prevent accidental impacts with the machine.
WARNING!
Before using the machine, check that the exit hole of the fountain and the
fans are free.
The maximum number of machines that can be connected in series using the
through connector is 6 units.
Make sure that the hopper lid is closed while the machine is running, in case
of fire of the
compound due to external causes extinguish it using sand.
Store the machine refill powder in a dry and dry place.
Clean the machine after each start in order to prevent breakdowns and always guarantee optimal operation. Create chains of up to 6 pieces, an excess of machines connected together can cause damage and in particular cases fire.
For better ventilation and consequent heat dissipation, do not block the air inlet and outlet fans.
The public and flammable materials must be kept at a minimum distance of 3
meters from the ZZSPARCOLDM.
Make sure that the light emission emitted by the machine does not come into
contact with any object.
ZZSPARCOLDM
does not produce open flames and is compatible with indoor use.
FEATURES
Generates a light fountain up to 5m high.
Easy to control and configurable in minutes, no license is required to use
this machine.
It works at room temperature so that sparks are not flammable.
It is possible to control the start and stop of the effect at any time via the
supplied remote control or via DMX control.
- Non-pyrotechnic effect
- Not explosive
- Not inflammable
- Cold bright fountain
- Adjustable height of the effect
- Control via DMX or remote control
- Vertical direction of the effect
- For indoor and outdoor use
- It does not require licenses to use
- Adjustable jet from 1 to 5 meters
- Total power 400W
CHECK THE CONTENTS
- ZZSPARCOLDM
- Operating instructions
- Power cable
- Wireless remote
UNPACKING INSTRUCTIONS
Carefully unpack the product to make sure all the parts are in the package and
are in good condition.
If the box or the contents (the product and included accessories) appear
damaged from shipping, or show signs of mishandling, notify the carrier or
dealer/seller immediately.
In addition, keep the box and contents for inspection.
TOP VIEW
-
Fountain exit, hole highlighted by the white plastic outline.
NEVER OBSTRUCT THIS OPENING! -
Dust tank.
Remove the rubber stopper to pour the mixture and refit before using the machine.
Put the powder only in to the tank!
Use only ZZIPP powder cod. ZZSPARKPOW
OPERATION
-
Signaling LED:
READY lights up green when the machine is ready for use.
DMX flashes red when a DMX signal is present.
FAULT lights up red when problems occur.
HEAT turns on when the machine is warming up, it turns off when the green
READY LED lights up. -
DISPLAY:
Indicates the DMX channel during DMX operation.
Indicates the temperature value in the heating phase.
Indicates the connection status in use with the remote control. -
POWER SWITCH
-
POWERCON SOCKETS POWER SUPPLY
-
DMX CONNECTIONS
WIRELESS REMOTE CONTROL
The machine has an internal receiver for the supplied remote control.
To enable the remote control, just press the red POWER button, the successful
connection will be indicated by the display showing FFF.
Press the ON button to activate the heating of the machine, at this point the
HEAT LED lights up red and the display shows the temperature value of the
machine. When it reaches a value of about 500, the red HEAT LED turns off and
lights up in green READY and the abbreviation FFF appears on the display, this
indicates that the machine is ready to operate.
Red Power Button:
Remote control enable button.
The machine is connected when it displays “FFF” on the display.
Button 1:
Active fountain with height 1
Button 2:
Active fountain with height 2
Button 3:
Active fountain with height 3
E-stop button:
Emergency stop
Clear powder button:
Press to remove dust residues in the mechanism, press OFF to stop the process.
Switching off:
Press the red button for 3 sec.
The machine has a continuous operation of 30 seconds, after which the fountain stops and it is necessary to press one of the buttons on the remote control to restart it.
DMX MODE & OPERATION DMX
The machine in DMX mode use 2 channels (see the following table).
Machine setup in DMX mode:
Turn on the machine, connect the DMX cable to the DMX IN socket and set the
address of the machine using the arrow keys next to the display.
Switch from remote control to DMX mode:
Connect the DMX cable, press the red button on the remote control for 3
seconds to disable the remote control, then set the DMX address using the
arrow keys.
CLEAN MACHINE
Empty the dust by turning the machine upside down and cleaning the residues
(DMX channel 1: 221 – 239) after use.
If the remains are blocked, it is necessary to open the housing and manually
rotate the chain counterclockwise.
The warranty expires once the machine stops working due to a lack of cleaning
after use.
WARNING!
The machine is built to generate a fountaine effect, never turn it upside down
during operation.
WARNING!
The maximum number of machines that can be connected in series using the
through connector is 6 units.
The declaration of conformity in the form complete can be found at the
company:
Zzipp Group S.p.a. or available online at the site:
zzippgroup.com
Consult the competent authorities for information on authorizations or possible restrictions before using the device.
imported and distributed by:
ZZIPP Group S.p.A.
Via Caldevigo 23/d, 35042 Este (PD)
0429 617 888
info@zzippgroup.com
zzippgroup.com
Read More About This Manual & Download PDF:
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>