ENFORCER NJ-A301U-T6AQ 30W PoE Injector Instruction Manual
- June 15, 2024
- ENFORCER
Table of Contents
30W PoE Injector
NJ-A301U-T6AQ
Installation Manual
NJ-A301U-T6AQ 30W PoE Injector
ENFORCER 30W PoE Injector converts 100~240 VAC to low voltage DC and supplies power to IP cameras, IP access control, and other PoE devices using Cat5e or Cat6 cables. This allows you to supply power to IEEE 802.3af/at compliant network accessories without an external power supply and provides a compact, reliable, and affordable solution to your networking infrastructure.
- Supports up to 30W on 2-pairs
- LED indicates power supply input and PoE output
- Internal AC/DC converter
- Easy Plug-and-Play installation
- Connects 10,100,1000BaseT PoE devices
- Overcurrent, overload, overvoltage, and anti-interference protection
- Supports Cat5e network cables and higher
- Compliant with IEEE 802.3af/at standard
Parts List
1x PoE Injector
1x Power Cord
1x Manual
Specifications
| Operating voltage | 100-240 VAC |
|---|---|
| Connections | Data In |
| PoE Out | lx Shielded RJ45 |
| PoE Power output | Up to 52VDC, 30W |
| Power link | Pin 1/2 (-), 3/6 (+) up to 30W |
| Network cables | Cat5e or higher |
| Protection | Overcurrent, overload, overvoltage, anti-interference |
| Ethernet speed | 10/100/1000 Mbps |
| LED Indicator | Green – power in, red – power out |
| Operating humidity | 90% (Maximum, non-condensing) |
| Operating temperature | 14°-104° F (-10°-°40 C) |
| Dimensions | 43/4″x2″x17/16″ (121x50x36 mm) |
Overview
NOTES:
- LED steady green indicates the PoE Injector has power.
- LED steady red indicates the device connected to the P+DATA port is powered.
Installation
- Use a CAT5e/6 UTP cable to connect device to the PoE Injector’s DATA IN port.
- Connect the AC power cable to the PoE Injector and power source.
- Connect the PoE OUT port to a PoE Device with CAT5e/6 UTP cable.
Sample Application
Troubleshooting
PoE device doesn’t function properly
- Ensure that all devices are turned on
- Ensure that the PoE device is functioning by plugging it directly into the PoE switch, computer, etc.
- Double-check that the cables were connected properly
- Run a continuity test on all wires in the cable
- Equipment at both ends must be at the same link speed, 10BaseT with 10BaseT, 100BaseT with 100BaseT, etc.
- Replace with a higher-grade cable for better performance
- Ensure that the cable lengths are within the allowable range and consistent with the remote PoE device power consumption, and reduce cable length as needed
- Check that power consumption is within the specifications
FCC COMPLIANCE STATEMENT
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO
THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL
INTERFERENCE AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED,
INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
Notice: The changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
IMPORTANT NOTE: To comply with the FCC RF exposure compliance
requirements, no change to the antenna or the device is permitted. Any change
to the antenna or the device could result in the device exceeding the RF
exposure requirements and void user’s authority to operate the device.
IMPORTANT: Users and installers of this product are responsible for
ensuring this product complies with all national, state, and local laws and
statutes related to monitoring and recording audio and video signals. SECO-
LARM will not be held responsible for the use of this product in violation of
any current laws or statutes.
IMPORTANT: Users and installers of this product are responsible for
ensuring that the installation and configuration of this product complies with
all national, state, and local laws and codes. SECO-LARM will not be held
responsible for the use of this product in violation of any current laws or
codes.
California Proposition 65 Warning :
These products may contain chemicals which are known to the State of
California to cause cancer and birth defects or other reproductive harm. For
more information, go to
www.P65Warnings.ca.gov.
WARRANTY: This SECO-LARM product is warranted against defects in material
and workmanship while used in normal service for one (1) year from the date of
sale to the original customer. SECO-LARM’s obligation is limited to the repair
or replacement of any defective part if the unit is returned, transportation
prepaid, to SECO-LARM. This Warranty is void if damage is caused by or
attributed to acts of God, physical or electrical misuse or abuse, neglect,
repair or alteration, improper or abnormal usage, or faulty installation, or
if for any other reason SECO-LARM determines that such equipment is not
operating properly as a result of causes other than defects in material and
workmanship. The sole obligation of SECO-LARM and the purchaser’s exclusive
remedy, shall be limited to the replacement or repair only, at SECO-LARM’s
option. In no event shall SECO-LARM be liable for any special, collateral,
incidental, or consequential personal or property damage of any kind to the
purchaser or anyone else.
NOTICE: The SECO-LARM policy is one of continual development and
improvement. For that reason, SECO LARM reserves the right to change
specifications without notice. SECO-LARM is also not responsible for
misprints. All trademarks are the property of SECO-LARM U.S.A., Inc. or their
respective owners. Copyright © 2023 SECO-LARM U.S.A., Inc. All rights
reserved.
U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606
Phone: 949-261-2999 |
800-662-0800
Website: www.seco-larm.com
Email: sales@seco-larm.com
PICSN7
MI_NJ-A301U-T6AQ_230624.docx
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>