SEALEY AK9991 Inclinometer Digital with Laser Instructions
- June 15, 2024
- SEALEY
Table of Contents
**SEALEY AK9991 Inclinometer Digital with Laser
**
Thank you
Thank you for purchasing a Sealey product. Manufactured to a high standard,
this product will, if used according to these instructions, and properly
maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE
OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND
WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE
DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE
INSTRUCTIONS SAFE FOR FUTURE USE.
-
Refer to instructions
-
Warning: Laser Beam
SAFETY
GENERAL SAFETY
✔ Maintain the inclinometer in good condition. Check controls and display
functions on a regular basis.
✔ Keep the inclinometer and charger cable clean for best and safest
performance.
✔ Wear approved safety eye protection.
✔ Maintain correct balance and footing. Ensure the floor is not slippery and
wear non-slip shoes.
✔ Keep children and unauthorised persons away from the working area.
✖ DO NOT use the inclinometer for a task it is not designed for.
✖ DO NOT operate the inclinometer when you are tired or under the
influence of alcohol, drugs or intoxicating medication.
✖ DO NOT get the inclinometer or charger cable wet or use in damp or wet
locations.
✔ Keep inclinometer and charger cable in a safe, dry, child proof area where
the temperature will not exceed 104°F (40°C).
ELECTRICAL SAFETY FOR USE OF USB CABLE
The Electricity At Work Act 1989 requires all portable electrical appliances,
if used on business premises, to be tested by a qualified electrician, using a
Portable Appliance Tester (PAT), at least once a year.
The Health & Safety at Work Act 1974 makes owners of electrical appliances
responsible for the safe condition of the appliance and the safety of the
appliance operator. If in any doubt about electrical safety, contact a
qualified electrician.
You must ensure that you:
✔ Inspect the charge cable and connector for wear and damage to ensure items
are safe before connecting to the power supply. If worn or damaged DO NOT use.
✖ DO NOT use any other type of charger with this product.
✖ DO NOT try to take the unit and charge lead apart.
✖ DO NOT get the inclinometer wet, or use in wet, damp conditions.
‰ WARNING! The warnings, cautions and instructions discussed in this
instruction manual cannot cover all possible conditions and situations that
may occur. It must be understood that common sense and caution are factors
which must be applied by the operator.
BATTERY SAFETY
‰ WARNING! To reduce the risk of burns or fire:
✖ DO NOT attempt to open, dismantle, modify or service the battery.
✖ DO NOT crush, puncture, short external contacts or dispose of in fire
or water. DO NOT expose to temperatures above 60°C (140°).
✔ Recycle or dispose of used equipment as stipulated by local regulation.
LASER SAFETY
The VS900.V4 utilises a Class II laser that emits low levels of visible
radiation (i.e. wavelengths between 400 and 700 nanometres) which are safe for
the skin but not inherently safe for the eyes. The Class II emission limit is
set at the maximum level for which eye protection is normally afforded by
natural aversion responses to bright light. Accidental eye exposure is
therefore normally safe, although the natural aversion response can be
overridden by deliberately staring into the beam, and can also be influenced
by the use of alcohol or drugs.
WARNING! DO NOT look or stare into the laser beam as permanent eye damage
could result.
Be aware that reflections of the laser beam from mirrors or other shiny
surfaces can be as hazardous as direct eye exposure.
INTRODUCTION
Digital inclinometer with laser line and four magnetic sides for measuring angles and tilt percentages on metal and other surfaces. Wide range of uses including setting suspension camber and caster, collision avoidance bumper mounted radar and parking assist systems. Absolute zero measure on any flat surface with accuracy ±0.2° and measuring range 4×90°. Large backlit LCD display makes it easier to see in a low-lit environment. Power supply 3.7V lithium battery. USB Type-C (cable included).
SPECIFICATION
Model No:………………………………………………….. AK9991
OPERATION
IMPORTANT WARRANTY INFORMATION
The battery fitted to this cordless tool is considered to be a consumable item and its ability to accept charge will reduce over time. Our warranty will cover genuine battery malfunction, but not fair wear and tear, for a period of 12 months.
ON/OFF Button (fig.1)
When unit is in the Off state, a short press will turn it turn on. In the
On state, a long press will turn
it off. When On, a short press once will turn on the right laser, short press
twice will turn on the left laser, short press three times will turn on both
lasers, short press four times will turn off the lasers.
When unit is turned on, place it onto the measuring surface (showing the angle
compared to absolute level) fig.3.1.
Press the ZERO button to reset the display to ” 0.00° ” fig.3.2.
Put the instrument on the surface that needs to be measured or change the
angle on the reference surface. The readout displays the angle value relative
to the reference surface (here it is 25°).
fig.3.3.
HOLD/Tilt% Button (fig.1)
To hold the current angle measured on the LED display, press and the
HOLD/Tilt% button.
To display Tilt%, hold the button down for approximately 2 seconds.
Tilt Direction (fig.2)
When the display shows ▲ on the left side and ▼on the right side it is
indicating that left side is higher than the right and vice versa.
NOTE: If the unit is not operated for 30 seconds it goes into standby
mode. If left for a further 3 minutes the unit will power down.
MAINTENANCE
Keep the inclinometer clean by wiping with a damp cloth.
Store inclinometer and USB cable in a dry, childproof area.
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools,
accessories and packaging should be sorted, taken to a recycling centre and
disposed of in a manner which is compatible with the environment. When the
product becomes completely unserviceable and requires disposal, drain any
fluids (if applicable) into approved containers and dispose of the product and
fluids according to local regulations.
WEEE REGULATIONS
Dispose of this product at the end of its working life in compliance with the EU Directive on Waste Electrical and Electronic Equipment (WEEE). When the product is no longer required, it must be disposed of in an environmentally protective way. Contact your local solid waste authority for recycling information.
BATTERY REMOVAL
Under the Waste Batteries and Accumulators Regulations 2009, Jack Sealey Ltd are required to inform potential purchasers of products containing batteries (as defined within these regulations), that they are registered with Valpak’s registered compliance scheme. Jack Sealey Ltd’s Batteries Producer Registration Number (BPRN) is BPRN00705.
Note: It is our policy to continually improve products and as such we
reserve the right to alter data, specifications and component parts without
prior notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is
required for any claim.
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk.
IP32 7AR
01284 757500
sales@sealey.co.uk
www.sealey.co.uk
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>