Rinnai CNTRLDRCIPW Wired Remote Controller Instruction Manual

Rinnai CNTRLDRCIPW Wired Remote Controller

Product Information

The Rinnai Wired Remote Controller is a device designed for operation and control of compatible Rinnai indoor models. It is compatible with the following Rinnai indoor models:

• DRCi DINLR07B1 DINLR09B1 DINLR11B1 DINLR13B1 DINLR15B1 DINLR18B1
• Hi-Wall HINRP20M HINRP26M HINRP35M HINRP50M HINRP60M HINRP70M
• Slim Ducted DINSD26MB DINSD35MB DINSD50MB DINSD70MB
• Cassette CIN20RMB CIN26RMB CIN35RMB CIN50RMB

The Wired Remote Controller can be used in both 1:1 and Multi configurations:

• This configuration contains one outdoor unit and one indoor unit.
• Multi
  This configuration contains one outdoor unit and two or more indoor units. The only models that may be installed in a multi configuration are Hi-Wall, Cassette, and Slim Ducted units. DRCi is a 1:1 configuration.

Product Usage Instructions

Safety Precautions
Before using the Wired Remote Controller, please read and follow these safety precautions:

• Avoid exposure to water or other liquids to prevent electric shock or fire.

• Avoid installation in areas with high temperatures, humidity, or flammable gases, as they may lead to abnormal operation,
  heating, or fire.

• Keep flammable gases away from the controller to prevent fire hazards.

• Do not touch the controller with wet hands to avoid electric shock.

• Ensure proper grounding of the controller to prevent electric leakage or heating that may result in fire.

• Handle the controller with care and avoid applying excessive force to the terminal.

• Refer to the wiring diagram in the installation manual for proper connection between the wired controller and the indoor unit.

Please note that these safety precautions are for informational purposes only and should be followed for safe operation of the product.

Note: The complete user manual contains additional sections such as Accessory Installation, Installation Method, Specifications, TFT Display, Controller Buttons, Operation, Wireless Control Connection, User Registration, Network Configuration, How to Use App, Warranty, and Contacts. Please refer to the user manual for detailed instructions on these topics.

MODELS CNTRLDRCIPW CNTRLDRCIPB

Wired Remote Controller Operation and Installation Manual

Congratulations on the purchase of your Rinnai Wired Remote Controller.
This manual describes safety precautions required for the use of the product.
· Read this manual carefully before installing or operating your wired remote controller. Make sure you understand the information provided before attempting to use the product.
· Keep this manual where it is readily accessible after reading it through.
· If another user operates the product in the future, be sure to hand over this manual to the new user.
· All the pictures in this manual are for explanation purpose only. They may be slightly different from the wired remote controller you purchased and the actual shape shall prevail.

This Wired Controller is compatible with the following Rinnai indoor models:

DRCi DINLR07B1 DINLR09B1 DINLR11B1 DINLR13B1 DINLR15B1 DINLR18B1

Hi-Wall HINRP20M HINRP26M HINRP35M HINRP50M HINRP60M HINRP70M

Slim Ducted DINSD26MB DINSD35MB DINSD50MB DINSD70MB

Cassette CIN20RMB CIN26RMB CIN35RMB CIN50RMB

This controller contains features and functions that are applicable to certain models in 1:1 and Multi configurations. In brackets NOTE next to the associated feature or function the applicable models will be listed. If no models are listed the feature or function is applicable to all.
1:1 – This configuration contains one outdoor unit and one indoor unit.
Multi – This configuration contains one outdoor unit and two or more indoor units. The only models that may be installed in a multi configuration are Hi- Wall, Cassette, and Slim Ducted units, DRCi is a 1:1 configuration.

DRCi R32 Wired Controller OIM

SAFETY PRECAUTIONS

This wired controller must be installed only by an Authorised
Person.
· IMPORTANT Installation by other persons may lead to imperfect installation,
electric shock or fire.
· Adhere to this installation manual. · Improper installation may lead to electric shock or fire. · Reinstallation must be made by an Authorised Person. · Do not uninstall the unit randomly. Arbitrarily uninstalling may
lead to abnormal operation, heating or fire of the air condition.

· Do not install the unit in a place vulnerable to leakage or

flammable gases. Once flammable gases are leaked and left

NOTE

around the wire controller, fire may occur.

· Do not operate with wet hands or let water enter the wired
controller. Otherwise, electric shock may occur.

· The wiring should adapt to the wired controller’s current.
Otherwise, electric leakage or heating may occur and result

in fire.

· The specified cables shall be applied in the wiring. No external
force may be applied to the terminal.

· The illustrations used in this manual are for explanatory
purposes only.

Rinnai

6

DRCi R32 Wired Controller OIM

BEFORE INSTALLING THE WIRED CONTROLLER
· This manual provides instructions for installing the wired
CAUTION controller. Please refer to the wiring diagram of this installation manual for connecting the wired controller with indoor unit.
· The wired controller operates in a low voltage loop circuit.
Strictly DO NOT directly contact the high voltage cable above, such as 115V,220V,380V. DO NOT allow the controller or controller loom to come in contact with high voltage cables such as 115V and above. Clearances for this situation shall be 300mm or more.
· The shielded wire of the wired controller must be grounded
firmly.
· After completing the wire controller connection, DO NOT use
Megger tester to check the insulation. That may damage the product.
A maximum of two controllers may be installed on a system and the mix may contain any of the following three controllers:
NOTE
CNTRLDRCINW / CNTRLDRCIPW / CNTRLDRCIPB

Rinnai

7

DRCi R32 Wired Controller OIM

ACCESSORY INSTALLATION

Select the installation location Don’t install at the place where cover with heavy oil, vapor or sulfureted gas, otherwise, this product would be deformed that would lead to system malfunction.
Preparation before installation

1. Please confirm that all the following parts have been supplied.

No. Name

Qty Remarks

1 Wired Controller

1–

2 Operation & Installation Manual 1 —

3 Screws

3 ST 3.9*25 (For mounting on the wall)

4 Wall Plugs

3 For Mounting on the Wall

5 Battery (CR2032)

1–

Rinnai

8

DRCi R32 Wired Controller OIM

INSTALLATION METHOD

Wired Remote Controller Dimensions

Figure 1. Dimensions

Remove the backing plate from the wired controller

· Insert a flat screwdriver into the
slots in the lower part of the wired

Srewdriver locations

controller (2 places). Rotate the

screwdriver (2 places) to remove the

backing plate (Figure 2).

Backing plate

Figure 2. Backing plate removal

Do not pry up and down, you can only rotate the screwdriver.
NOTE

Rinnai

9

DRCi R32 Wired Controller OIM

The PCB is mounted in the upper part of the wired controller. Be careful not to damage the board with the slot screwdriver.
NOTE
Fasten the back plate of the wired controller
· Fasten the back plate on the wall with the 3 screws (ST3.9*25) and plugs
(Figure 3) provided.

Figure 3.
Fasten the back plate of the wired controller
· Remove plastic knockout from the backing plate (Figure 4). · Create a hole in the wall to access the wall cavity for routing the loom from FCU
to controller.

Rinnai

Remove knockout

Put on a flat surface. Be careful not to distort NOTE the back plate of the wire controller by over tightening the mounting screws.

Figure 4.

10

DRCi R32 Wired Controller OIM

WARNING KEEP BATTERIES OUT OF REACH OF CHILDREN. Swallowing may lead to serious injury in as little as 2 hours or death, due to chemical burns
and potential perforation of the oesophagus. If you suspect your child has swallowed or inserted a button battery immediately call the
24-hour Poisons Information Centre on 13 11 26 for fast, expert advice. Examine devices and make sure the battery compartment is correctly secured, e.g.
that the screws or other mechanical fasteners are tight. DO NOT use if compartment is not secure. Dispose of used button batteries immediately and safely. Flat batteries can still be dangerous and may be a choking hazard. Inform others about the risk associated with button batteries and how to keep their children safe. Remove the batteries if the remote is not going to be use for prolonged periods. This will help prevent damage from leaking
batteries. If leakage has occurred and corrosion is evident the remote will need to be replaced. Leaking chemicals are toxic and MUST NOT be touched or ingested. NEVER mix old and new batteries. DO NOT immerse the remote control in any liquid, this will damage the remote control, rendering it inoperable and voiding
its warranty.

Battery Installation (CR2032)
· Slide the battery into the holder as shown with the
positive side facing up (Figure 5).
· Put the battery into the installation site and make sure
the positive side of the battery is in accordance with the positive side of installation site.
· On the first power up set the time of day. If the system
is exposed to a power outage the battery will maintain the time of day. If the displayed time is not correct once power is restored replace the battery.

Figure 5.

Rinnai

11

DRCi R32 Wired Controller OIM

Thermostat Connection to Indoor Unit

Loom Knockout

Figure 6. Model A

Indoor Unit PCB

Setting up two Controllers

Up to two controllers may be connected to the HA and HB terminals on the indoor unit as detailed below. From factory, all controllers are supplied with SW1 dip switch setting 1′ OFF and dip switch setting2′ OFF. When configuring a second controller to the DRCi system, two dip switches on the rear of the second controller (SW1 location) must change to the ON position as shown below. Dip switch settings for the primary or master controller must remain unchanged. Refer to Figure 7.

Controller 1 (Master) SW1

Controller 2 (SUB) SW1

ON 12
ON 12

Figure 7.

If two controllers are installed the secondary `SUB’ controller is not capable of the following functions:

l Setting Time and Date l Weekly Schedule

l Timer On / Off

Rinnai

12

DRCi R32 Wired Controller OIM

Wi-Fi control may be setup on one of the controllers only. There is no polarity between HA and HB (Figure 8).

Maximum 40m

Earth the shield
Maximum 40m

Figure 8.
DO NOT allow water to enter the wired control. Use the trap and putty to seal the wires. Connecting wires must be fixed reliably NOTE and cannot be pulled.
For some units, one wired controller can support multiple units (maximum of 16 units). For configuration of multiple indoor units loom connection is polarity sensitive and HA must connect to HA on all indoor units, the same applies to HB. In group control, there will be no error displayed on the wired controller (Figure 9).

Rinnai

13

DRCi R32 Wired Controller OIM

Total length 40m maximum
Figure 9.
Indoor Unit Connect the terminals on the wired controller (HA ,HB), and the terminals of the indoor unit (HA ,HB). There is no polarity between HA and HB (Figure 10).
Indoor Unit
HA HB
Wired Controller

Rinnai

Figure 10.

14

DRCi R32 Wired Controller OIM

Reattach backing plate of the wired controller To reconnect the fascia to the backing plate, anchor the top lugs first as shown below then swing the fascia down and press lightly to engage the bottom tabs, be careful not pinch the loom during this process (Figure 11).
Figure 11. All the illustrations in this manual are for explanation purposes only. Your wired controller may be slightly different. The actual NOTE shape shall prevail.

Rinnai

15

DRCi R32 Wired Controller OIM

4. SPECIFICATIONS

Models
Input Voltage Ambient Temperature Ambient Humidity

CNTRLDRCIPW CNTRLDRCIPB 12V~24V
0~43°C
RH40%~RH90%

Wiring Specifications

Controller loom shall be 2-Core (0.5 mm.sq) shielded cable up to 40m long. Rinnai accessory CNTRLLOOM2W18M is 18m long NOTE and may be used for this purpose.

Rinnai

16

DRCi R32 Wired Controller OIM

5. FEATURES
Feature and Functions of the Wired Controller
· TFT Display. · Malfunction Code Display:
shows the error code which is ideal for service.
· 4-way wire layout design. No
raised section at back-end so more convenient to fit the wires and install the device.
· Room Temperature Display. · Weekly Timer.

Function:

· · Mode: Choose Auto-Cool-Dry-Heat-Fan Auto Restart

· · Fan speed: Auto/Low/Med/High Speed

Automatic Airflow Test (DRCi)

· Swing (1:1 & Multi ­ Hi-Wall)

· Dual Control

· Timer ON/OFF

· Group Control

· Temp Setting

(1:1 – DRCi / Cassette)

· Weekly Timer

· Child Lock

· Follow Me

· LCD Display

· Turbo

· Clock

· 24-hour System

· 12-hour System

Rinnai

17

DRCi R32 Wired Controller OIM

6. TFT DISPLAY

MODE display Displays the current mode,including:
Function display

Time

Status Bar

08: 1 5 AM
26°C .5 26.5°C

FAN SPEED display Displays selected fan speed: LOW MED HIGH
TURBO
AUTO

Child lock Temperature Mode Warning Function Self clean display
1:1 ­ DRCi / Cassette / Hi-Wall

Navigation Bar Wireless control feature display Room temperature display
Follow me feature display
ECO feature display 1:1 – DRCi / Hi-Wall / Cassette
Filter Cleaning Remind 1:1 & Multi ­ Cassette / Hi-Wall SLEEP feature display

Choose Timer
Set up
Timer settings
Delay off display
Vertical Louver Swing 1:1 & Multi ­ Hi-Wall Horizontal Louver Swing 1:1 & Multi ­ Hi-Wall

Rinnai

18

DRCi R32 Wired Controller OIM

7. CONTROLLER BUTTONS

1 2
Rinnai

3 4

5
1 Menu 2 Return 3 ON/OFF 4 Enter 5 Left / Right, Up / Down

19

DRCi R32 Wired Controller OIM

8. OPERATION
Introduction to Button Setting Start the remote control
1. Wired controller connected to power. 2. Press the ” ” to start the device. 3. Enter the main page display.

08: 1 5 AM
26°C .5
26.5°C

08: 1 5 AM, Sun, Nov. 1 9
O

Power-on status main page display

Shutdown status main page display

Rinnai

20

DRCi R32 Wired Controller OIM

Standby State
1. Occurs after no button operation for 30 seconds. 2. After entering the standby state, the controller exits all setting states and
restores the main page display.

08: 1 5 AM, Sun, Nov. 1 9

26°C

26.5°C

.0 66%

Screen Off
1. Occurs after no button operation for 60 seconds (including 30 seconds of standby).
2. TFT screen off. Press any key to exit the screen-off state. The home page display interface will be restored.

Rinnai

21

DRCi R32 Wired Controller OIM

8-Degree Heating Function (1:1 – Hi-Wall / DRCi / Cassette [Exc: Multi]) In cold climates this feature assists with maintaining the home or room at 8°C. ON/OFF Press this button to change the on/off state of the wired controller. Up/Down Press the ” ” or ” ” to adjust the parameters, or adjust the cursor selection items up or down in the setting state. Left/Right Press the ” ” or ” ” to select the setting item Left/Right, or enter or return to the previous menu during menu setting. Return Press the ” ” to re turn to the main page display, or return to the previous menu during menu setting. Enter Press the ” ” to confirm the change of the currently selected setting item, or enter the next level menu when the menu is set. Menu Press the ” ” to set the status of the menu.

Rinnai

22

DRCi R32 Wired Controller OIM

Mode Setting 1. In the non-menu setting state, press ” ” or ” ” to select the mode setting.
08: 1 5 AM Auto Cool Dry Heat

2. Press ” ” or ” ” to select mode, and then press ” ” to change the setting mode.
3. The most selected modes are Auto, Cool, Dry, Heat, Aux Heater, Aux Heat+Heat, Fan.
4. When the Auto or Dry mode is selected, the fan speed is fixed, the fan speed cannot be adjusted, while the set temperature is adjustable.
5. When the Cool or Heat mode is selected, the fan speed and temperature can be adjusted.
6. When the Fan mode is selected, the temperature display will be greyed out, and the temperature cannot be adjusted.
7. When the mode is set to Aux Heater mode, the fan speed becomes Auto wind, which cannot be adjusted. At this time, switch to other modes, and the fan speed no change.

Rinnai

23

DRCi R32 Wired Controller OIM

8. In Aux Heater mode, sleep, 8-degree heating, turbo, and rotation functions cannot be turned on.
9. When the mode is set to Aux Heater + Heat mode, the fan speed is auto wind. At this time, Turbo and Rotation functions cannot be turned on, and the fan speed cannot be adjusted.
10. Aux Heater mode and Aux Heat+Heat mode can be set only when it is detected.
Set Temperature Setting
1. Press the button ” ” or ” ” to set the room temperature. Indoor Setting Temperature Range: 10/16/17/~30°C or 20~28°C (model dependant).

Fan Speed Setting
1. In the non-menu setting state, press ” ” or ” ” to select ” setting function is unavailable under Auto or Dry mode.

“. Fan speed

08: 1 5 AM High Med Low Auto

2. Press ” ” or ” ” to select the fan speed, and then press ” ” to change the fan speed;

Rinnai

24

DRCi R32 Wired Controller OIM

3. Press ” ” or ” ” to select Customised Fan Speed, and then press ” ” to enter stepless speed regulation.
Fan Speed
50%

4. In stepless speed regulation Setting state, press ” Fan speed, the setting range is 1%~100%.
5. Press ” ” to exit stepless speed regulation.

” or ”

” to adjust the

Fan Direction Setting (1:1 & Multi – Hi-Wall / Cassette) 1. In the non-menu setting state, press ” ” or ” ” to select ” “.
08: 1 5 AM Vertical Louver Swing Horizontal Louver Swing

Rinnai

25

DRCi R32 Wired Controller OIM

2. Press ” ” or ” ” to select the fan direction function, press ” ” to enable or disable the function; whether there is a fan direction function is determined by indoor unit.

08: 1 5 AM
26.5°C 58%

26.5°C

66 %

3. When Horizontal Louver Swing is selected, press ” Horizontal Swing function.
4. When Vertical Louver Swing is selected, press ” Vertical Louver Swing function.

” to enable/disable the ” to enable/disable the

• Swing option is available on Rinnai Cassettes and Hi-Wall split systems.

5. When the Four-Way Swing is selected, press ” “, and use ” ” or ” ” to select the fan direction menu.
08: 1 5 AM Unit A Unit B

Rinnai

26

DRCi R32 Wired Controller OIM

6. If indoor unit is TWINS model, you need to select the Unit A or Unit B, then set the basic swing function.

Swing 01 Swing 02 Swing 03 Swing 04

Four-Way Swing

7. When Breezeless is selected, press ” ” to enable/disable the Breezeless function. The Breezeless function can only be set when the setting mode is set to Cool. Turn on the Breezeless function to cancel the Turbo, ECO, GEAR, Horizontal Louver Swing, Wind On, Wind Away Anti-Wind Blowing.
8. When Wind On is selected, press ” ” to enable/disable the Wind On function. The Wind On function can be set only when Auto, Cool, Heat.
9. When Wind Away is selected, press ” ” to enable/disable the Wind Away function. The Wind Away function can only be set when Auto, Cool, and Heat.
10. When Anti-Wind Blowing is selected, press ” ” to enable/disable the AntiWind Blowing function. The function can only be set when the setting mode is set to Cool, Dry and Fan.

Special Function Settings Turbo
1. Press ” “, use ” ” or ” ” to select ” “, press ” ” or ” “, then turn on Turbo.
2. The Turbo wind speed icon on the home page is displayed ” “.

Rinnai

27

DRCi R32 Wired Controller OIM

Follow Me
1. Press ” “, use ” ” or ” ” to select ” “, press ” ” or ” “, then turn on Follow Me.
2. Turn on Follow Me function, and set the room temperature to Indoor unit. 3. Turn on the Follow Me function to cancel the 8-degree heating function.

ECO
(1:1 – Hi-Wall / DRCi / Cassette [Exc: Multi])
1. Press ” “, use ” ” or ” ” or ” ” to select ” “, press ” ” or ” “, then turn on ECO.
2. Under COOL mode, turn on the ECO function to cancel breezeless, turbo, sleep, and gear functions.
3. When the ECO function is switched from off to on, when the set temperature is less than 24°C, the temperature will change to 24°C.
4. When the ECO function is switched from the off state to the on state, the fan speed defaults to auto. By changing the fan speed, it does not exit the ECO function.

Sleep
1. Press ” “, use ” ” or ” ” or ” ” to select ” “, press ” ” or ” “, then turn on Sleep.
2. Under Auto, Cool, turn on the sleep function to cancel Turbo, ECO and 8-degree heating functions.
3. Turn on the sleep function and the fan speed is fixed as auto.

Rinnai

28

DRCi R32 Wired Controller OIM

Special Function Setting

1. When the home page is displayed, press ”
setting.
Menu

” to enter the special menu

Turbo

Follow Me

ECO

Gear

100%

Fresh Air

Turbo

2. Press ” ” or ” ” to select special function setting ” Settings ” ” , Timing settings ” “, system settings ” ” ” to enter the next menu.

” Smart Control “, Press ” ” or

3. In the menu setting state, if the selected item has a next-level menu, you can press ” ” or ” ” to enter the next-level menu. Press ” ” or ” ” to return to the previous menu;

4. Press ” ” or ” ” to adjust options or parameters;

5. Press ” ” to confirm to enable/disable the function.

6. Whether there have special function is determined by indoor unit.

Child Lock

1. Press ” ” to select special function setting ” “.
2. Press ” ” or ” ” to turn on Child Lock. 3. There will be a second confirmation prompt when opening the Child Lock,
select Confirm again to open the Child Lock. 4. When the Child Lock is turned on, the wired controller does not receive the
remote control signal.

Rinnai

29

DRCi R32 Wired Controller OIM

5. When the Child Lock is turned on, you can use the key combination ” ” + ” “. Press and hold for 3 seconds to exit Child Lock. When the Child Lock is not turned on, also use the key combination. Press and hold for 3 seconds to activate the Child Lock.

Menu

C/F Switching

C

The keypad will be locked,press confirm to the

homeOTpAagInes.tTaoll unlock the keypad,press” ” and ” “keys for 3 seconds to turn off

the child lock function.

Cancel

Confirm

Menu C/F Switching
Press the ” ” and ” “keys simultaneously for 3 seconds to turn off the child lock function

Filter Cleaning Reminder
Press ” ” , use ” ” or ” ” to select ” ” , press ” on Filter Cleaning Remind, symbol lights up ” “.

” or ” “, then turn

Self-Clean (1:1 – Hi-Wall / DRCi / Cassette / Slim Ducted [Exc: Multi])
This process assists with cleaning the indoor coil and depending on the appliance it can take up to 90 minutes to complete.
1. Press ” ” , use ” ” or ” ” to select ” ” , press ” ” or ” “, then turn on Self-Clean.
2. When the self-clean is turned on, cancel the fresh air and daily timer functions. Auto with Temperature Range
1. Press ” ” , use ” ” or ” ” to select ” ” , press ” ” or ” “, then turn on Auto with Temp Range.

Rinnai

30

DRCi R32 Wired Controller OIM

2. The temperature difference between the upper and lower limits of the set temperature is greater than or equal to 5°C.
3. The parameters that can be set when the temperature zone control function is turned on are: MaxTemperature, MaxTemperature, (Time of Validity). The set parameters are saved, and it is still valid after power-off and power-on.

Auto with Temp Range

Auto with Temp Range

Max Temperature Max Temperature Term of Validity

30°C 16°C Permanent

Permanent Custom Time

Term of Validity

Permanent
Custom Time Start Time Stop Time

Term of Validity

08:00 20:00

4. The setting of Max Temperature and Min Temperature must satisfy MinTemperature + 5°C Max Temperature;
5. Time of Validity can be set to Permanent or Custom time.

08: 1 5 AM
30.0°C Max
1 6.0°C Min

26.5°C

Daily Timer
1. The daily timer can be set timer on or timer off. 2. The daily timer is treated as an absolute time (the clock on the wired
controller), when the daily timer is up, the wired controller is turned on or off.

Rinnai

31

DRCi R32 Wired Controller OIM

3. The daily timer information will take effect immediately if ” ” or ” ” is pressed.
4. When the scheduled power-on and power-off time are the same, the system will automatically add 10 minutes to identify the power-on and power-off time.

Daily Timer Timer On Timer Off

Daily Timer

09:00 – – :- –

Timer On
08 00 AM

Weekly Timer After the weekly timer function is turned on, you can set the daily timer work status separately.
1. Press ” ” use ” ” or ” “, to select ” “, then open Weekly Timer.

Menu Daily Timer Daily Timer Delay Off

Weekly Timer

On

Weekly Timer

Off

Sun

Mon

Tue

Wed Thu

Fri

Sat

Rinnai

32

DRCi R32 Wired Controller OIM

2. Use ” “, ” “, ” ” or ” ” to select the timer date, and use “ADD” to add the set time, include Timer On, Timer Off, Temp, Mode, Fan Speed.

Weekly Timer

Weekly Timer

Sun Mon Tue Wed Thu

Fri

Sat

Add

Timer On
Timer Off Temp Mode

Weekly Timer

09:00 AM
02:00 PM 26.0°C

Save

Delete

3. After the operation is complete, select “Save”.

Timer On
Timer Off Temp Mode

Weekly Timer

09:00 AM
02:00 PM 26.0°C

Save

Delete

4. After completing the settings, you can quickly copy then use the timer through Copy Timer.

Weekly Timer

Weekly Timer

Sun Mon Tue Wed Thu

Fri

Sat

Copy Timer

09:00 -14:00 09:00 -14:00

66°F 66°F

Mon Tue Wed Thu Fri

Copy Timer

Weekly Timer

Weekly Timer

Sun Mon Tue Wed Thu

Fri

Sat

Copy Timer

09:00 AM -02:00 PM 09:00 AM -02:00 PM

26.0°C 26.0°C

NOTE
Rinnai

The weekly timer function is only valid if it is set for at least one day.

33

DRCi R32 Wired Controller OIM

Delay off 1. Press ” “, use ” ” or ” to select ”
Menu Daily Timer Weekly Timer Delay off

” , and then turn on Delay off.
On Off

2. Press ”

” or ”

” to select the following menu.

Off Now 30 mins Later
1 hour Later 2 hour Later

Delay Off

3. When the Delay off function has been activated, when the user press ” ” again, a reminder of the remaining delay time will pop up, and you can choose to Off Now or Off Later.

Languages

English

Francais

Delay off function is set. It will turn off after 6 9 mins.

DeutschDo you want to turn off now or later?

Italia

Off Later

Off Now

Espana

4. The Delay off setting has a power-down memory function. The user needs to manually exit the Delay off function.

Rinnai

34

DRCi R32 Wired Controller OIM

Remote control reception

This option is applicable to Hi-Wall and Cassette models supplied NOTE with a remote control and are configured to a wired controller.

1. The wired controller has the function of remote control reception. After receiving the valid code of the remote control, the TFT display status will be refreshed according to the data such as the switch of the remote control code, the set temperature, the set mode, the fan speed and the timer switch value. The information is sent to the indoor unit.
2. The wired controller does not receive the digital display remote control code.
3. When the Follow Me’ function is enabled on the wired controller,Follow Me’ signal is received and processed on the remote control as an invalid signal. When Follow Me’ function is turned off on the wired controller, Follow Me’ remote control signal is forwarded to the air conditioner and the wired controller. Do not process the remote control signal of follow me, and do not open follow me function.
4. When the child lock function is turned on, the remote control does not receive remote control signals.

Auto Restore
1. Press ” “, use ” ” or ” ” to select ” “.Press ” ” or ” “, then turn on Auto Restore.
2. When the function of Auto Restore to original setting is changed from off to on, the current setting mode, set temperature and set fan speed status are memorised.

Rinnai

35

DRCi R32 Wired Controller OIM

3. When the user changes the set mode, set temperature and set fan speed to make them different from the state in memory, start the time counting; when the timer expires, restore the set mode, set temperature and set fan speed to the memory. (Only restore the set mode, set temperature, set fan speed, do not change the switch state). When the switch state changes, the original setting function will be restored if it is not cancelled.
4. If the user wants to update the memorised fixed mode, set temperature and set fan speed status, it is necessary to turn off the function and then turn it on again.
5. When the function of Auto Restore to original setting is enabled, if the weekly timer function has been turned on, a pop-up window will remind the user that there is a conflict of functions. It is necessary to confirm that weekly timer function is turned off. If the user chooses to confirm, the weekly timer will be turned off and continue to enter the automatic recovery setting interface, select Cancel Return directly.
6. When the weekly timer function is turned on, if the Auto Restore function has been turned on, a pop-up window will remind the user of the function conflict. It is necessary to confirm that the timer recovery original setting function is turned off. If the user chooses to confirm, the Auto Restore will be turned off and continue to enter the weekly timer setting interface, select Cancel Return directly.

Rinnai

36

DRCi R32 Wired Controller OIM

Wi-Fi Configuration ­ Smart Control Settings
1. ” “, use ” ” or ” ” to select ” “.
2. During the smart control setting, if the wired controller is not connected to the network, Step 1, Step 2, and Step 3 section of the network configuration guide will be displayed in sequence under user operation. When `Step 3′ of the following Smart Control process is displayed, the wired controller will automatically enter the AP network configuration state. If the network configuration is successful, it will prompt the connection completion.

Smart Control ­ Step 1
Smart Control Download the app & activate product

Smart Control ­ Step 2
Smart Control Download the app & activate product

Step1. Please scan the QR code on the manual to download & install the APP for smart phone control.
1/ 3
Smart Control ­ Step 3
Smart Control Download the app & activate product
Step3. Add the device and set up the network configuration with your phone. 3-1. Make sure your phone is connected to WI-FI/ Wireless networks . 3-2. Press the POWER button for 3s on the thermostat
3/3

Step2. Sign up for registration on the app.
2/3
Smart Control ­ Step 4
Smart Control
Done! You can now control the air conditioner though the app.

Rinnai

37

DRCi R32 Wired Controller OIM

3. During smart control setting, if the wired controller is connected to the Internet,
and the network can be reconfigured; after the user reconfirms, the network configuration guide will be displayed.

MSumltairtlaCnognutraogl es

EN

PT The product is currently connected to

the Internet, do you need to reconfigure

DE

the network?

IT

Online download

Reconfigure

MSumltairltaCnognutargoel s

EN

PT

The pCroodnufircmt istocurerrceonntfilygcuorenntheectneedtwtoortkhe? Internet, do you need to recongure the

DE

network?

IT

Cancel

Online download

Recongure

Confirm

Buzzer
1. When the buzzer is set to be valid, while the wired controller has a valid key operation, the buzzer will sound once.
2. When the buzzer is set to be invalid, the buzzer does not sound when there is a button operation on the wired controller.

Language
1. System language settings can be set to English, French, Italian, Portuguese or Spanish.
2. A prompt will pop up again during the setting. After the customer reconfirms, the display of the wire controller will automatically change to the corresponding language.

Rinnai

38

DRCi R32 Wired Controller OIM

Data & Time Setting
1. The lower section of date & time setting can set 12/24 hour system switching, wired controller time setting or wired controller date setting.

24-Hour Time Timer Setting Date Setting

Date & Time Setting
09:00 Nov-17-2021

2. The time setting interface of the wired controller is as follows:
Timer On
08 00 AM

3. The date setting interface of the wired controller is as follows:
Date Setting

NOV 10 2021

°C/°F Switching
Press ” ” and ” ” for 3 seconds will alternate the temperature display between the °C & °F scale.

Rinnai

39

DRCi R32 Wired Controller OIM

9. WIRELESS CONTROL CONNECTION
Safety Precautions
· Read the safety precautions carefully before installing the unit. · Refer to the following important safety issues that must be observed. · Applicable system: iOS, Android. (Recommended: iOS 10.3, Android 6.0)
· APP can not support the latest software version of Android and
iOS system.
· NOTE Due to special circumstances that have occurred, we explicitly claim below: Not all of the Android and iOS systems are compatible with APP. We will not be responsible for any issues as a result of the incompatibility.

Wireless safety strategy
· Wi-Fi only support – WPA-PSK/WPA2-PSK encryption and non encryption.
WPA-PSK/WPA2-PSK encryption is recommended.

· Smart Phone camera needs to be 5 million pixels or above to

ensure QR scan works sufficiently.

· CAUTION

Due to different network conditions, occasionally a response

time-out occurs. Therefore, it may be necessary to repeat

network configuration.

· Due to different network set-ups, sometimes control process

may return time-out. If this occurs, the display between board

and App may not be the same. This is not an issue.

Rinnai

40

DRCi R32 Wired Controller OIM

Rinnai will not be liable for any issues and problems caused by Internet, Wi- Fi Router and Smart Devices. Please contact the NOTE original provider for assistance.
Download and Install APP The APP system is subject to update without prior notice for product function improvement. The actual network configuration process may be slightly different from the manual, the actual process shall prevail. Please check the service website for more information.
The following QR Code is only available for downloading the APP.
CAUTION
Android Phone Users: scan Android QR code or go to Google Play and search “NetHome Plus” APP and download the app. IOS Users: scan iOS QR code or go to APP Store and search “NetHome Plus” APP and download the app. .

Rinnai

Android

iOS

41

DRCi R32 Wired Controller OIM

10. USER REGISTRATION · Please ensure your mobile device is connected to the Wi-Fi router. Make sure
the Wi-Fi router is connected to the internet before completing user registration and network configuration.
· It’s better to log in your email box and activate your registration account by
clicking link in case you forget the password. You can log in with the third party account details.
0

Android

iOS

1. If you do not have an account Click “Select

Account”.

2. Enter your email address and password, then click “Register”.

Rinnai

42

DRCi R32 Wired Controller OIM

· Make sure your devices are powered on. · Keep your mobile phone close enough to your device when
NOTE
you are connecting network to your device.
· Connect your mobile phone to the wireless network at home,
and make sure you know the password of the Wireless Network.
· Check if your router supports 2.4 GHz Wireless Network band
and turn it on. If you are not sure whether the router supports
2.4 GHz band, please contact the router manufacturer.
· The device cannot connect to the Wireless Network that
requires authentication, and it usually appears in public area
such as hotels, restaurants, etc. Please connect to a Wi-Fi that
does not require authentication.
· It is recommended to use a Wireless Network name that only
contains letters and numbers. If your Wireless Network name
contains special characters, please modify it in the router.
· Turn off the WLAN+ (Android) or WLAN Assistant (iOS)
function of your mobile phone when connecting network to
your devices.
· If your device was previously connected to the Wireless
Network and needs to reconnect, please click “+” on app Home page, then add your device again by the device category and
model according to the instructions on app.

Rinnai

43

DRCi R32 Wired Controller OIM

11. NETWORK CONFIGURATION

· You must select your Wi-Fi network for successful registration.
Turn off your `mobile data’. Ignore any other network and CAUTION make sure the Android or iOS device is only connected to the
Wireless network you want to configure.
· Make sure the Android or iOS device connected to your Wi-Fi
is functioning well and can connect back to your original Wi-Fi
network automatically.

How to enter AP distribution network
Press ” “, use ” ” or ” ” to select the Smart Control ” network. AP mode is activated if the icon is flashing.

“, to connect to the

Using Android or iOS device to complete network configuration
· Make sure your mobile device has already been connected to the Wi-Fi network
which you want to use. Ignore other irrelevant Wi-Fi networks as it may influence
your configuration process.

When your Air Conditioner (AC) enters into AP’ mode, the airconditioning remote controller can’t control it. It is necessary to NOTE finish network configuration or power the AC again in order to control it. Alternatively, you need to wait 8 minutes to let the AC quitAP’ mode automatically.

There are two ways to complete the network configuration:

· NOTE

Network configuration by Bluetooth scan

· Network configuration by select appliance type

Rinnai

44

DRCi R32 Wired Controller OIM

Network configuration by Bluetooth scan
Make sure the bluetooth function of your mobile device is switched on and working.
NOTE

1. Open the APP and Press “+ Add Device”.

2. Press “Scan for nearby devices”.

Rinnai

45

DRCi R32 Wired Controller OIM

3. Wait for smart device to complete search, then click to Add Device.

4. Select home Wi-Fi, enter your own Wi-Fi router password and click OK.

Rinnai

46

DRCi R32 Wired Controller OIM

5. Wait for connection to the network.

6. Configuration Success, you can now modify the default name.

Rinnai

47

DRCi R32 Wired Controller OIM

7. You can choose an existing name or customise a new name.

8. Bluetooth network configuration is successful, now you can see
the device in the list.

Rinnai

48

DRCi R32 Wired Controller OIM

Network configuration by selecting appliance type

1. If the bluetooth network configuration has failed, please select the appliance type.

2. Please follow the above steps to enter “AP” mode.

Rinnai

49

DRCi R32 Wired Controller OIM

9:41 Choose Method
Scan QR code on the unit Note: Wait 5-10 seconds while your device is in AP mode before scanning the QR code.
Manual Setup

3. If choosing the network configuration method.

4. If choosing the “Scan the QR code” method.

Steps 3 and 4 are applicable to Android system only. iOS system does not need these two steps.
NOTE

Rinnai

50

DRCi R32 Wired Controller OIM

5. If choosing the “Manual Setup” method (Android). Connect to the wireless network (iOS).

6. Please enter password.

Rinnai

51

DRCi R32 Wired Controller OIM

7. Network configuration is successful. The App is now fully configured for use.

8. Configuration Success, you can see the device on the list. You can now operate your system from anywhere with an internet connection.

Rinnai

52

DRCi R32 Wired Controller OIM

When finishing network configuration, APP will display “success” NOTE on the screen.
Due to changes in the internet settings, the device status may still display “offline”. If this occurs, refresh the device list on the APP and make sure the device status shows “online”. Alternatively, user can turn off the AC power and turn it back on again. The device status will become “online” after few minutes.

Rinnai

53

DRCi R32 Wired Controller OIM

12. HOW TO USE APP
· Please ensure your mobile device is connected to the Wi-Fi router. Make sure
the Wi-Fi router is connected to the internet before using the App to control the air conditioner via internet. Please follow the next steps.

1. Type your account and password 2. Select your appliance. and sign in.

Rinnai

54

DRCi R32 Wired Controller OIM

3. Touch to turn on. The user can control the AC on/off status, operation mode, fan speed, temperature, etc.
Depending on your specific air conditioning system, some NOTE functions may not be controllable.

Rinnai

55

DRCi R32 Wired Controller OIM

Special Functions
Schedule
User can schedule daily to turn air conditioner ON/OFF at any specific time of day during the week. User also can choose circulation to keep the AC under schedule
control every week.

Rinnai

56

DRCi R32 Wired Controller OIM

Sleep
User can customise their own comfortable sleep by setting an overnight target temperature. To access Sleep, system must already be operating in heating or cooling mode.

Rinnai

57

DRCi R32 Wired Controller OIM

CAUTIONS Wireless Network module models: US-SK107, EU-SK107:
FCC ID: 2ADQOMDNA21
IC: 12575A-MDNA21
This device complies with Part 15 of the FCC Rules and it contains licence- exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s).
Operation is subject to the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause undesired operation of the device.
Only operate the device in accordance with the instructions supplied.
Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with FCC radiation exposure limits set forth for an uncontrolled environment. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna shall not be less than 20cm (8 inches) during normal operation.

Rinnai

58

DRCi R32 Wired Controller OIM

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC NOTE Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
· Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
· Consult the dealer or an experienced radio/TV technician for
help.

Rinnai

59

DRCi R32 Wired Controller OIM

13. WARRANTY
TERMS OF WARRANTY ­ AUSTRALIA
Rinnai Australia Pty. Ltd. ABN 74 005 138 769, 100 Atlantic Drive, Keysborough VIC 3173.
NOTICE TO CONSUMERS UNDER AUSTRALIAN CONSUMER LAW
Our goods and services come with guarantees that cannot be excluded under the Australian Consumer Law.
For a major failure with a good, you are entitled to a replacement or refund and compensation for any other reasonable foreseeable loss or damage. If the failure does not amount to a major failure and if the goods fail to be of acceptable quality, you are also entitled to have the goods repaired or replaced.
For a major failure with the service, you are entitled to cancel your service contract with us and obtain a refund for the unused portion, or to compensation for its reduced value. You are also entitled to be compensated for any other reasonably foreseeable loss or damage. If the failure does not amount to a major failure you are entitled to have problems with the service rectified in a reasonable time and, if this is not done, to cancel your contract and obtain a refund for the unused portion of the contract.
The benefits provided by this Warranty are in addition to any other rights and remedies available to a consumer under the Australian Consumer Law and any other law which may apply to the goods and or services.

Rinnai

60

DRCi R32 Wired Controller OIM

WARRANTY: DRCi R32 Wired Controller
This product is warranted for a period of one (1) year from the date of purchase, in accordance with the Terms and Conditions of Warranty detailed below.
IMPORTANT ­ TO BE READ IN CONJUNCTION WITH THE TERMS AND CONDITIONS OF WARRANTY
· The fitness for purpose of the Rinnai DRCi R32 Wired Controller and ensuring
suitable Wi-Fi connectivity is the sole responsibility of the Qualified Installer and or Purchaser.
· The DRCi R32 Wired Controller must be installed by a suitably Qualified Installer
in accordance with local and national wiring codes, otherwise the warranty will be void.
· Always refer to the Installation and Owner’s Manuals to ensure the correct
installation and operation procedures have been followed.
· The DRCi R32 Wired Controller is to be installed indoors only; warranty
excludes damage caused by the elements such as rain, wind, lightning, or harmful environmental conditions.
· For full Terms and Conditions, go to the Rinnai website, www.rinnai.com.au

Rinnai

61

DRCi R32 Wired Controller OIM

NOTES

Rinnai

62

DRCi R32 Wired Controller OIM

NOTES

Rinnai

63

DRCi R32 Wired Controller OIM

CONTACTS

innai Australia Pty Ltd

ABN 74 005 138 769 | AU45204
100 Atlantic Drive, Keysborough, Victoria 3173 P.O. Box 460, Braeside, Victoria 3195 Tel: (03) 9271 6625 Fax: (03) 9271 6622
National Help Line Tel: 1300 555 545 Fax: 1300 555 655 Monday to Friday, 8.00 am to 5.00 pm EST.
Cost of a local call may be higher from a mobile phone. (National calls from public phones in Australia are free.)
For further information visit www.rinnai.com.au or email enquiry@rinnai.com.au
innai has a Service and Spare Parts network with personnel who are fully trained and equipped to give the best service on your innai appliance. If your appliance requires service, please call our National Help Line.
With our policy of continuous improvement, we reserve the right to change, or discontinue at any time, specifications or designs without notice.

B065557

DRCi R32 Wired Controller 120P OIM ­ Issue 2 May 2023

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>