HARLEY-DAVIDSON Saddle Tramp 2014-2022 Lower Fairing Audio Upgrade Kit Installation Guide

: June 15, 2024
: HARLEY-DAVIDSON

HARLEY-DAVIDSON Saddle Tramp 2014-2022 Lower Fairing Audio Upgrade Kit

HARLEY-DAVIDSON Saddle Tramp 2014-2022 Lower Fairing Audio Upgrade Kit
Ins

TOOLS & INSTALLATION ACCESSORIES REQUIRED

Torx® Drivers T-10,T-15, T-20, T-25
Phillips screwdriver
Sockets wrenches, 7/16, 1/2.
3/8 Drill bit
Blue Thread-locker
*Silicone (3MSCLR), gasket tape (IBSPKGTP)
*(4) #14 X 3/4” Hex head screw
*(2) 3/8 wire grommet
Masking tape Part Components
*Optional

Lower Fairing Audio Upgrade Kit

Visit MetraPowerSports.com for more detailed information about the product and up-to date vehicle specific applications.
Note: This Installation will reuse hardware from the existing mounted lower fairing. Note: Not compatible with the Rockford Fosgate OE system.

Attention! We recommend removing the main battery fuse prior to installation. When testing the after-market equipment, ensure that all factory equipment is connected before cycling the key to ignition.

Product Features

Sound-optimized enclosure for improved bass performance
Molded tray fits snugly into lower fairings
OE Fit and finish
Painted a complimentary Matte Black finish

Part Applications

Harley Davidson FLHT, FLHTCU, FLHTCUL, FLHX, FLHXS, FLTRX, FLTRXS, FLTRXSE (w/ lower fairings) 2014-Up (†)
(†) Does not fit Twin-Cooled® models
(†) FLHX models require purchase of lower fairing kit

Part Components

A) Speaker enclosure (L & R)

B) Enclosure tray (L & R)
Part Applications
C) Infinity Kappa Perfect 6.5″ Speakers

D) HM-9722 harness (not Shown)

PREPARATION

Attention! To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding.

Open left side saddle bag lid.
Rotate (2) mounting studs counter clockwise until released, then lift off saddle bag
Remove left side access cover.
For vehicles equipped with security siren: Verify that the Hands-Free Fob is present.
Cycle the key to the ignition position.
Remove main fuse.
(Figure A)

Models Equipped With Fairing Lowers

Open lower fairing glove box door.
Remove 7/16 in. nut securing the lower fairing cap.
(Figure B.1)
Remove fairing cap.
(Figure B.2)
Remove lower fairing clamp screw and 1/2 in. nut. ( Figur e B.3)
Remove (2) 7/16 in. flange nuts securing upper clamp, then remove fairing assembly.
(Figure B.4)

FAIRING DISASSEMBLY

Speaker Pod

From the front, remove the (2) screws , block-off panel then glove box.
(Figure A.1,2,4)
*Attention: Take precautions not to brake of the lock positioning tab.
(Figure A.3)
Disconnect the vent door linkage and separate assembly from fairing.
(Figure B.1 )

Lower Fairings

From the back, remove the (3) screws.
(Figure C.1)

Speaker / Glove Box housing

If equipped, remove the (3) glove box screws.
(Figure A.1)
Remove glove box tray.
(Figure A.2)
Remove the linkage screw.
(Figure B.1)
Separate linkage assembly.
**(Figure B.2, B.3)

**

INSTALLATION

Speaker Pod and Tray

Tip: To ease assembly, first install then remove the (5) screws in the enclosure without the tray.

Optional: To maximize performance apply silicone (3MSCLR) to the tray mating surface.
(Figure A.1)
Assemble the speaker enclosure to the tray.
(Figure B.1)
*Note: If you do not apply silicone, install (2) #14 X 3/4” hex head screw to seal and hold
the tray in place.
(Figure B.3)
Optional: to maximize performance apply gasket tape (IBSPKGTP) to the tray mating
surface.
**(Figure B.5)

**

Speaker Enclosure / Tray

Reattach the screw and the linkage onto the new enclosure front. Tighten the screw to 1.3–2 N·m (12–18 in-lbs).
Position the enclosure assembly and connect the linkage.
(Figure A.1)
Once the linkage is connected, from the rear, re-install (3) coarse thread screws.
Tighten the screws to 1.3–2 N·m (12–18 in-lbs)
**(Figure B.1)

**

Speaker Enclosure / Tray

Optional: To prevent unwanted rattle or vibration; fold a piece of gasket tape over the locating tab from the block-off panel.
(Figure A.1)
Install the block-off panel.
(Figure A.2)
Apply thread locker to the threads of the (2) screws then install the screws and tighten to 7.3–8.4 N·m (65–75 in-lbs).
(Figure A.3)
On the back side of the fairing, measure about 25 mm (1.0 in) over and 9.5 mm (⅜ in) up from the lower fairing cap mating flange.
(Figure B.1)
Mark the location to drill the hole. Cover the drill point with masking tape to prevent cracking or chipping of the paint. Drill a 9.5 mm (⅜ in) hole in the glove box inboard side wall.
(Figure B.2)

*Optional: Insert a rubber grommet to protect the HM-9722 wires.
Install the lower fairing: leave the lower fairing cap off.
Route the speaker wires through the hole in the lower fairing.
Route the wiring harness under the fairing up to the radio and connect to the Kappa Perfect KP5004 amp. Connect the black Front channel Molex connector from the KP5004 (amp #2) to the HM-9722 harness. Make sure the White Molex connections from channels 5 & 6 of the DSP/Interface is plugged into the Front input channels of the amp.
Secure wire harness and verify wiring does not interfere with steering or suspension travel.
Install the lower fairing cap.
Rear Tour-Pak Speakers
Rear Tour-Pak Speakers
Remove the two speaker grilles (B) from the 600X along with the 6.5” speaker and harness.
Separate the metal grille from the speakers mounting ring. Grille are pressure fitted in and can be 000difficult to remove, be careful not the bend or damage grille.
Wire up the supplied speaker harness to the OE speaker wires. Secure with zip-ties. (speaker pod 5 000image)
Place the 6.5” speaker into the mounting ring and place into lower fairing speaker pod
Secure speaker into place
Insert the grille so the Infinity logo is symmetrical on both sides of the bike.

NOTE:

To prevent possible damage to the sound system, verify that the ignition key switch is in the OFF position before installing the main fuse.

See the service manual and install the main fuse.
Test the sound system for proper operation.
See the service manual. Install the outer fairing and windshield.

WARNING:

Be sure that steering is smooth and free without interference
Interference with steering could result in loss of vehicle control and death or serious injury
Be sure that wires, harnesses or lines do not pull tight when handlebars are turned fully to left or right fork stops
Verify that steering is smooth and clear from stop to stop

NOTE:
If objectionable vibration occurs due to high levels of bass response, additional foam may be inserted between block-off panels and fairing lowers.

Kits Fitment

Grand American Touring
Electra Glide [Batwing]
| Electra Glide Standard| FLHT| 2014| 2022
Electra Glide Ultra Classic| FLHTCU| 2014| 2019
Electra Glide Revival| FLH| 2022| 2022
Electra Glide Ultra Classic Low| FLHTCUL| 2015| 2016
Electra Glide Ultra Classic Low Twin Cooled| FLHTCUL TC| 2015| 2016
Electra Glide Ultra Classic Twin Cooled| FLHTCU TC| 2014| 2016
Ultra Limited [Batwing]
| Touring Ultra Limited| FLHTK| 2014| 2022
Touring Ultra Limited Shrine| FLHTK SHRINE| 2014| 2022
CVO Ultra Limited| FLHTKSE| 2014| 2022
Touring Ultra Limited Low| FLHTKL| 2015| 2022
Touring Ultra Limited Anniversary| FLHTK ANV| 2018| 2018
CVO Ultra Limited Anniversary| FLHTKSE ANV| 2018| 2018
Road Glide [Sharknose]
| Touring Road Glide Limited| FLTRK| 2020| 2022
CVO Road Glide| FLTRXSE| 2018| 2022
Touring Road Glide| FLTRX| 2015| 2022
Touring Road Glide Special| FLTRXS| 2015| 2022
Touring Road Glide Ultra| FLTRU| 2016| 2019
CVO Road Glide Ultra| FLTRUSE| 2015| 2016
Street Glide [Batwing]
| Touring Street Glide| FLHX| 2014| 2022
Touring Street Glide Special| FLHXS| 2014| 2022
CVO Street Glide| FLHXSE| 2015| 2022
Touring Street Glide Anniversary| FLHX ANX| 2018| 2018
Touring Street Glide Special Anniversary| FLHXS ANX| 2018| 2018
Touring Street Glide Shrine| FLHX SHRINE| 2014| 2014
2 Speaker kit upgrades| 4 Speaker kit upgrades| 6 Speaker kit upgrades
---|---|---
NOTE: If more than one option is needed a second INFPWSKP5004XAM will be required.| NOTE: If adding a lower fairing pods a second INFPWSKP5004XAM will be required.|
Tour PAK upgrade- If bike has tour Pak only needs Infinity 600X, no harnessing| Saddlebag upgrade| Lower fairing pods-

INFKPNTCKIT = Non-Twin Cooled INFKPTCKIT = Twin Cooled

| Lower fairing pods-

INFKPNTCKIT = Non-Twin Cooled INFKPTCKIT = Twin Cooled

| Lower fairing pods-

INFKPNTCKIT = Non-Twin Cooled INFKPTCKIT = Twin Cooled

Audio Options

Customer Support

Metra Saddle Tramp | HARMAN Infinity

MetraOnline.com | harmanaudio.com
MetraPowerSports.com

Having difficulties? We’re here to help.
Contact our Tech Support line at:
386-257-1187

Or via email at:
techsupport@metra-autosound.com

Tech Support Hours (Eastern Standard Time)
Monday – Friday: 9:00 AM – 7:00 PM
Saturday: 10:00 AM – 5:00 PM
Sunday: 10:00 AM – 4:00 PM

KNOWLEDGE IS POWER Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry. Log onto www.installerinstitute.com or call 800-354-6782 for more information and take steps toward a better tomorrow.

Symbol Metra Recommends MECP certified technicians