JBC HRL-A Articulated Left Hand Rest Instruction Manual

JBC HRL-A Articulated Left Hand Rest

This manual corresponds to the following reference: HRL-A

Packing List

The following items are included:

Articulated Left
Hand Rest Arm ………… 1 unit

Height Adj
Flange …… 1 unit
Ref. 0023991

Manual ………………………. 1 unit
Ref. 0028802

Features

Assembly

Setting up the Articulated Hand Rest

Fit the shaft into the flange bushing (1) and tighten the headless screw at the rear (2). Then assemble first the height adjustment flange (3) and finally the hand rest arm (4) onto the shaft. The hand rest arm position should be like shown in the image. The left hand rest is marked at its bottom side with the letter “L”.

Height Adjustment
According to your work needs the articulated hand rest allows adjustment for different heights through the vertical axis. Slide the arm to the appropriate height (1) and secure it by tightening the knob (2) to guarantee stability.

Work Position Adjustment

• HRL Articulated Left Hand Rest allows adjustment for different positions according to your work needs.
• The articulated arm covers the entire working area.

The correct hand work positon ist shown in the following images:

Accessories

If a second hand rest is needed, HRR Articulated Right Hand Rest is available. HRR also allows adjustment for different positions.In the case of using both left and right arms, assemble both as shown in the illustration according to the letters on the back of the hand rest, to keep the hand supports at the same level. The right hand rest  should be assembled below the left hand rest.

HRL
Articulated Left Hand Rest

HRR
Articulated Right Hand Rest

Compatible JBC Articles

• HRR and HRL can be combined with: RWT Adjustable Rework Arm, RWS Adjustable Rework Arm for PHSE and  RWB Adjustable Rework Arm for PHBE.
• Assemble first the height adjustment flange 1), then the HRR (2) and afterward the HRL (3). Assemble the second height adjustment flange (4) and finally the RWT (5).

4 different sizes for PCB Supports are available

• PHNS Support for PCBs up to 11×7 cm / 4×3”
• PHSS Support for PCBs up to 13×13 cm / 5×5”
• PHBS Support for PCBs up to 36×28 cm / 14×11”
• PHXLS Support for PCBs up to 51×61 cm / 20×24”

Maintenance

• Check periodically that the HRL is clean, especially the sliding parts and the shaft.
• Use a damp cloth when cleaning. Alcohol can only be used to clean the metal parts.
• Replace any defective damaged parts.
• Use original JBC spare parts only.
• Repairs should only be performed by a JBC authorized technical service.Do not leave the HRL over the preheater when it is in operation.

Safety

It is imperative to follow safety guidelines to prevent electric shock, injury, fire or explosions.

• Do not use the equipment for any purpose other than PCB rework. Incorrect use may cause a fire.
• The temperature of accessible surfaces may remain high after the unit is turned off. Handle with care.
• Be careful with the fumes produced when soldering.
• Keep your workplace clean and tidy. Wear appropriate protection glasses and gloves when working to avoid personal harm.
• Do not leave up the arms directly above heat surfaces.
• Utmost care must be taken with liquid tin waste which can cause burns.
• This appliance can be used by children over the age of eight as well as persons with reduced physical, sensory or mental capabilities or lacking experience provided that they have been given adequate supervision or instruction concerning the use of the appliance and understand the hazards involved.
• Children must not play with the appliance.
• Maintenance must not be carried out by children unless supervised.

Specifications

HRL
Articulated Left Hand Rest

Ref. HRL-A

• Arm Lenght: 444,5 mm / 17.5 in
• Total Net Weight: 1.06 kg / 2.34 lb
• Package Dimension / Weight: 280 x 280 x 164 mm / 2.18 g
• (L x W x H) 11.02 x 11.02 x 6.46 in / 4.80 lb

Complies with CE standards
ESD Safe

Warranty

JBC’s 2 year warranty covers this equipment against all manufacturing defects, including the replacement of defective parts and labour. Warranty does not cover product wear or misuse. In order for the warranty to be valid, equipment must
be returned, postage paid, to the dealer where it was purchased. This product should not be thrown in the garbage. In accordance with the European directive 2012/19/EU, electronic equipment at the end of its life must be collected and returned to an authorized recycling facility.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>