HOMCOM 820-195V70 Electric Fireplace Heater User Manual

HOMCOM 820-195V70 Electric Fireplace Heater

Product Information

Product Usage Instructions

1. Do not use two high-power appliances in the same socket.
2. The plug needs to be plugged in fully.
3. Product socket cannot use extension cord.
4. The socket needs to be conformed to BS1363.
5. The maximum withstand current value needs to be greater than 13A (Only for UK market).

IMPORTANT. RETAIN FOR FUTURE REFERENCE READ CAREFULLY

PACKING DETALS

TOTAL 2 BOXES

Installation

The Electric heater is supplied with approximately 1. 7 meters of flexible mains cable (1 mm2).The appliance and surround should be located close to a suitable mains socket and MUST be easily accessible to allow proper connection.
This heater MUST be earthed. If in any doubt consult the manufacturer, its service center or a qualified person.

Note: After inset the heater into the wooden mantel: .

1. Loose 4pc silver screws on the top, 2pc silver screws on the left and 2pc silver screws on the right out a little, and leave 2mm gap.
2. The two keyhole slots of fixing bracket alignment with the two loose silver screws 2. Slide the top fixing bracket rightward and slide the left bottom and right bottom fixing brackets downward to lock the fixing bracket in place
3. Fix the heater to the inside wall of the surround firmly using the 8pcs ST4x12 screws.

Important Safety Instructions

When using this electrical appliance, basic precautions should be followed to reduce the risk of fire, electric shock, and injury to person, including the following:

• This heater must be used on an AC supply only and the voltage marked on the heater must correspond to the supply voltage.

• Do not switch the appliance on until it properly installed as described in this manual.

• The heater must not be located immediately below a socket outlet.

• Keep furniture, curtains and other flammable material at least 1 meter away from the appliance.
  Never closed to curtains and other combustible material, otherwise may cause risk

• Do not leave the appliance unattended during use.

• Do not leave the appliance unattended whilst connected to the mains supply.

• Keep out of reach of children and do not allow them to operate this appliance.

• This appliance is intended for household use and should not be used for industrial purposes.

• From time to time, check the cord for damage. Never use the appliance if the cord or any part of the appliance shows signs of damage.

• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.

• Do not operate this appliance with a damaged plug or cord, after a malfunction or after being dropped or damaged in any way.

• Repairs to electrical appliances should only be performed by a qualified electrician.Improper repairs may place the user at serious risk.

• Do not run the mains cable under carpets, rugs etc.

• Do not allow the mains cable to hang over sharp edges or come into contact with hot surfaces.

• WARNING: In order to avoid overheating, do not cover the heater.

• Never immerse the product in water or any other liquids.

• Do not use this heater in the immediate surroundings of a bath, a shower or a swimming pool.

• Dot use this heater with a programmer, timer or any other device that switches the heater on automatically, since a fire risk exists if the heater is covered or positioned incorrectly.

• Do not use the appliance outdoors.

• Do not use if you have wet hands.

• Never use the appliance on or near hot surfaces.

• Do not operate with a damaged cord.

• Before cleaning the appliance, ensure it is unplugged from the power and that it is completely cooled.

• Do not clean the appliance with abrasive chemicals.

• Never use accessories that are not recommended or supplied by the manufacturer. It could cause danger to the user or damage to the appliance.

• This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance.

• Cleaning and user maintenance shall not be made by children without supervision.

• Do not lift the appliance by the front panel.

• CAUTION: In order to avoid a hazard due to inadvertent resetting of the thermal cutout, this appliance must not be supplied through an external switching device, such as a timer, or connected to a circuit that is regularly switched on and off by the utility.

• WARNING: This heater is not equipped with a device to control the room temperature.

• Do not use this heater in small rooms when they are occupied by persons not capable of leaving the room on their own, unless constant supervision is provided.

• Children of less than 3 years should be kept away unless continuously supervised.

• Children aged from 3 yeani and leas than 8 years shall only switch on/off the appliance provided that it has been placed or installed in its intended normal operating position and they have been given supervision or instruction conceming use of the appliance in a safe way and undel’8tand the hazards Involved. Chlldren aged from 3 yeal’8 and less than 8 yeal’i ,hall not plug In, regulate and clean the appliance or perform uaar maintenance.

• CAUTION: some parts of this product can become very hot and cause bums. Partlcular attention has to be given where children and vulnerable people are present.

• Regarding lhe inatructions tor replacing lamp and installation, than kl to refer to the below paragrapl\l of the manual.

• Regarding lhe lnformallon for lnatallallon, refer to the followlng parts.

• A.Do not use two high-power appliances in the same socket.

• B.The plug needs to be plugged in fully.

• C.Product socket cannot use extension cord.
  The socket need to be conformed to BS1363, The maximum withstand current value needs to be greater than 13A (Only for UK market).

Contents of carton

• Heater.
• Remote conlrol.
• 1 lnatrucUon Manual.

Instruction for Use

The appliance can be operated either by lhe ewltchea located al the fronl right hand tide above tha fire or bv tha auoollad remote control.

1. Cursor
2. Day time
3. Timer
4. Standby
5. Temperature/serial number display
6. Timer off
7. Timer on
8. Time/Temperature display
9. Automatic control of heating
10. Heating position
11. Flame brightness

• Temperature and serial number display: Normally it displays the room temperature; while setting the temperature, the setting temperature is displayed; When setting the timer, serial number is displayed.
• Time/ Temperature display: Normally it displays the current time; while setting the timer, the setting time is displayed. When setting the temperature of the week timer, the setting temperature is displayed.
• Time on and time off: It is displayed while setting the timer, and it is used in combination with serial number setting.
• Flame brightness: It displays the current brightness of the flame, which ranges from one to five positions.

Manual Operation

This is done by operating the switches located at the front of the fire .The standby rocker switch must first be switched on, the fire will beep to indicate that it is powered up.
Press the 0/1 button once to turn the heater and flame effect on. A red indicator light will appear to indicate that the function is ON. Press the 0/1 button for 3 seconds this will operate the flame brightness setting. Hold the button down until the desired flame brightness is obtained and there will be 5 levels flame brightness available.
Press the POWER button once for the low heat setting 1 000W; press twice for the high heat setting 2000W; press three to switch off the heat setting.
Press the BACK LIGHT button to adjust the colors of LED decoration, 7 colors available.

Remote Operation

The standby rocker switch located at the front of the fire must first be switched on; the fire will beep to indicate that it is powered up.
It takes a little time for the receiver to respond to the transmitter. Do not press the buttons more than once within two seconds for the fire to operate normally.

1. Boot steps
2. Connect the power
3. Turn on the power switch
4. Press the control switch or “ON/OFF” key of the remote controller to start up
5. Press the 1000W/2000W button once for the low heat setting 1 000W; press twice for the high heat setting 2000W; press three to switch off the heat setting.
6. Press the DIMMER button to operate the dimmer mode, repeat pressing will raise and lower the brightness.
7. Press the BACK LIGHT button to adjust the colors of LED decoration, 7 colors available.

Automatic heating

Press “IC” button on the remote controller to start or exit the automatic heating.
The heater displays AUTO symbol at automatic heating status. The heater will adjust the heat settings between 1 000W and 2000W automatically according to the room temperature and temperature setting. During a timed starting process, it is possible to start heating ahead of schedule.
NOTE: Maybe the heater will turn the heating on automatically prior to the set time maximum20 minutes.

Setting the day and time

1. Settings are done on the remote controller
2. Press “DATE TIME” button, then press the key to select the day
3. Press “DATE TIME” button again, then press the”+” or”-” to set the hour
4. Press “DATE TIME” button again, then press the”+” or”-” to set the minute
5. Press “OK” button to complete

Temperature setting
The default set temperature is 20 °C, press “+” or “-” on the remote controller to set the temperature, which ranges from 15 to 30°C. And this setting is only for the temperature in the normally mode, not for the temperature in the timer mode.
NOTE: The set temperature must be higher than the room temperature for the heat working.

Timer setting

1. Description of timer setting

2. There are up to 10 items for timer setting

3. Each setting item has its date, power-on time and shutdown time

4. The max. duration of each setting item is 23 hours 50 minutes

5. The setting date for each item can be any day or days of a week

6. The date in each setting item represents the date of power-on time

7. If the shutdown time of the setting falls on the second day, it is unnecessary to set the date – you just set the shutdown time

8. Steps to view the timer setting

9. Press the “TIMER SET” button

10. Press the “+” or”-” to check the power-on time of the timer one by one.

11. For checking the shutdown time, press the” .” button

12. Press the “+” or”-” to continue viewing

13. For deleting the current item of setting, press “C” to delete

14. Steps for timer setting

15. Select the settings of the serial number
    Press the “TIMER SET” button, and the serial number starts blinking Press the “+” or”-” to change the serial number until you get the serial number that you need to set or modify.

16. Select date
    Press” TIMER SET” button once again, and the cursor on the left side of day starts blinking Press the keys to move the cursor to the corresponding day, press the”+” to add the corresponding day, or press “-” to delete the day until you have completed the selection of all dates

17. Set the start time
    Continue to press the” TIMER SET” button, the hour starts blinking Press the”+” or”-” to adjust the hour
    Continue to press the” TIMER SET” button, the minute starts blinking Press the”+” or”-” to adjust minute

18. Set the shutdown time
    Then press the “TIMER SET” button, the display is off, and the hour starts blinking Press the”+” or”-” to adjust the hour.
    Continue to press the” TIMER SET” button, the minute starts blinking Press the”+” or”-” to adjust minute

19. Set temperature
    Then press the” TIMER SET” button, and the temperature set starts blinking. At this moment, the temperature displayed is normally set temperature, which can be adjusted by pressing “+”or”-“

20. Press” TIMER SET” button to continue setting, and press “OK” complete the setting

Timer switch

• “TIMER ON/OFF” is to control the timed opening and closing Restart the machine after power is cut off, the timer setting is kept, but the current date and time must be reset
• NOTE 1: Press the 1 000W button or 2000W button, or IC button to active the heating when timer ON after finish a timing setting. The heater only has flame effect working if you have not selected the desired heating.
• NOTE 2: Repeat the same procedures to set more timing cycles if required after the 01 timing cycle is finished.
• NOTE 3: When the week timer setting is finished, “TIMER ON/OFF” function can be effective.

Safety Cut-Off

• This appliance is fitted with a safety cut-off which will operate if the fire overheats (e.g. Due to blocked air vents). For safety reasons, the fire will NOT automatically reset.
• To reset the appliance, disconnect the appliance from the mains supply for at least 15 minutes.
• Reconnect the supply to the mains and switch on the appliance.

Troubleshooting

Cleaning and Maintenance

Warning-Always disconnect from the mains supply before cleaning heater.
For general cleaning use a soft clean duster – never use harsh abrasive or cleaners.
The glass viewing screen should be cleaned carefully with a soft cloth. DO NOT use proprietary glass cleaners.
This product does not use a standard bulb for its flame effect. The appliance uses an electronically controlled LED system to create the effect, therefor no parts need to be replaced. There are no user-serviceable parts on this appliance. Under no circumstances should the appliance be serviced be anyone other than a qualified electrician.

Disposal

At the end of the product’s serviceable life it should be disposed of thoughtfully and safely in accordance with local authority regulations. The plug should be Removed from the power supply cord and the power cord cut from the heater

Technical Specification

• Supply: 220-240V- 50Hz
• Rated power: 2000W
• Illumination: LED system {no replaceable parts)

Meaning of crossed -out wheeled dustbin:
Do not dispose of electrical appliances as unsorted municipal waste, use separate collection facilities.
Contact you local government for information regarding the collection systems available.
If electrical appliances are disposed of in landfills or dumps, hazardous substances can leak into the groundwater and get into the food chain, damaging your health and well-being.

If you have any questions, please contact our customer care center.
Our contact details are below: e 0044-800-240-4004

enquiries@mhstar.co.uk

IMPORTER ADDRESS:
MH STAR UK LTD Unit 27, Perivale Park, Horsenden lane South Perivale, UB6 7RH MADE IN CHINA

Table for information requirements for electric local space heaters.

Model identifier(s):820-195V70

Item| Symbol| Value| Unit| Item| Unit
Heat output| Type of heat input, for electric storage local space heaters only (select one)
Nominal heat output| ****

pnom

| 2.0| kW| Manual heat charge control with integrated thermostat| N/A
Minimum heat output (indicative)| ****

pmin

| ****

1.0

| kW| Manual heat charge control with room and/or outdoor temperature feedback| ****

N/A

Maximum continuous heat output| ****

p max

| ****

2.0

| ****

kW

| Electronic heat charge control with room and/or outdoor temperature feedback| ****

N/A

Auxiliary electricity consumption| Fan assisted heat output| N/A
At nominal heat output| elm.,| 0.014(fan motor)| kW| Type of heat output/room temperature control (select one)
At minimum heat output| elmin| 0.014(fan motor)| kW| Single stage heat output and no room temperature control| [no]
In standby mode| el88| 0.48| w| Two or more manual stages, no room temperature control| [no]
 |  |  |  | With mechanic thermostat room temperature control| [no]
 |  |  |  | With electronic room temperature control| [no]
 |  |  |  | Electronic room temperature control plus day timer| [no]
 |  |  |  | Electronic room temperature control plus week timer| [yes]
 |  |  |  | Other control options (multiple selections possible)
 |  |  |  | Room temperature control, with presence detection| [no]
 |  |  |  | Room temperature control, with open window detection| [no]
 |  |  |  | With distance control option| [no]
 |  |  |  | With adaptive start control| [yes]
 |  |  |  | With working time limitation| [no]
 |  |  |  | With black bulb sensor| [no]

Contact details:

| IMPORTER ADDRESS: MHSTARUKLTD

Unit 27, Perivale Park, Horsenden lane South Perivale, UB6 7RH MADE IN CHINA

Remark:

For electric local space heaters, the measured seasonal space heating energy efficiency 11s cannot be worse than the declared value at the nominal heat output of the unit.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>