Kaka Glow GM-Mizar Solar Outdoor Lights User Manual

June 16, 2024
Kaka Glow

Kaka Glow GM-Mizar Solar Outdoor Lights

Kaka Glow GM-Mizar Solar Outdoor Lights

INTRODUCTION

Thank you for purchasing the solar PIR motion sensor light. We hope you enjoy our solar lighting solution. To ensure proper operation of this solar light, please read this user manual carefully and keep it for future reference.

PACKAGE LIST

| Solar PIR Motion Sensor Light
---|---
User Manual
Installing Screws Wall Bracket
Plastics Expansion Anchors
Wire Master

PACKAGE LIST

Solar Panel 1.5W
Battery 3, 7V 2200mAh
LED Quantity 333pcs
Rated Power 8w
Net Weight 421g
Waterproof Rate IP65

PRODUCT FEATURES

Easy installation and energy-saving solar technology.
Wide application in gardens, garages and some other places.
Fully automatic operation. Automatically turns off during the day time and automatically lights up when it senses motions at night.
Add-in Wire Master make possible to tum the lights on during day time.

Remarks

This is a solar power product, please make sure to expose the solar panel in sufficient sunshine for effective charging during day tine.
Sufficient sunshine charges the battery for longer illumination time. Install the light in height of 5.9-7.2ft(1.8-2.2m) is recommended.

3 LIGHTING MODES

Mode 1:
When PIR senses a motion, the light turns on at 100% brightness.
The lights tum off in 20 seconds after the object is gone.
Mode 2:
When PIR senses a motion, the light turns on with 100% brightness.
After 20 seconds when the object is gone, lights keep on with 10% brightness
Mode 3:
The light stays on at 30% brightness at night without infrared induction. With the assist of Wire Master make it possible even during day time.

INSTALLATION

  1. Drill three holes on the wall for wall bracket installation.
  2. Fix the plastic expansion anchors into the wall.
  3. Assemble the wall bracket on the wall and twist screws into plastic expansion anchors (Please make sure the bracket fixed tightly).
    Plug the solar motion sensor light into the wall bracket. Flip the switch to the mode you need.

NOTES

  1. The internal light sensor limits the motion sensor off during the daytime. A smart stand by of motion sensor makes extremely low power consumption when the light is in pure darkness.
  2. The product is equipped with a built-in lithium battery, please do not replace it by yourself, put it with household garbage or place it near any heat source. If you would like to dispose this product, please put it to battery recycle center.
  3. A full charge requires up to 8 hours of sunlight. The location of solar panel, weather condition and the seasonal variation will directly affect the charging efficiency to battery. Real working time of the light will be variant condition by condition.
  4. Please note that the Wire Master will stop battery charging when it’s switched to “Work” side. For battery charging request, please switch it to “Charge” side.

3-STEPS INSTALLATION

3-steps Installation

It’s bothering how to tum on the Soler light during the day lime
For example, we put the light in garage but outside is a big sunny clay
3-steps Installation

To tum on the light in day time:

  1. Plug the Wire Master between the light and the wire from solar panel
  2. Press the switch of Wire Master to “Work “side, and choose “Mode” of lights (Please refer to tile “3 LIGHTING MODES” in USER MANUAL), the lights will turn on according to the “Mode” setting.
  3. Note that when switch to ‘Work’ ‘side, battery charging will be stopped.
  4. Press the switch lo “Charge “side, battery charging will be started.

CAUSION!! The Wire Master Is limited for Ka Ka GLOW SSPL-01. Abusive use of the Wire Master may lead lo unknown danger.

Read User Manual Online (PDF format)

Loading......

Download This Manual (PDF format)

Download this manual  >>

Related Manuals