DINAN D760-0070 G2x G4x B46 Cold Air Intake System Instruction Manual

DINAN D760-0070 G2x G4x B46 Cold Air Intake System Instruction Manual

Thank you for being selective enough to choose a DinanPerformance Intake System. The Dinan Engineering Team has spent many hours developing this product to assure that you will receive increased performance, durability and an aesthetic design that you as a customer will be able to enjoy for many years. Ease of installation and maintenance is important to us and has been highly considered throughout the design process

Prior to performing the installation, familiarize yourself with these instructions as it should help you with the process. If you feel that you do not have the required skills or tools, please arrange for a qualified repair facility to perform the installation.

If you have any difficulties during the installation, or if these instructions are not clear to you, please call Dinan’s Technical Support Staff at 800-341-5480.

Again, thank you for choosing Dinan. Enjoy.

PARTS LIST

REMOVAL OF STOCK SYSTEM

STEP 1:

1. Unplug the sensor harness from the airbox
2. Loosen clamp and remove the airbox from the vehicle Ensure that the rubber mounting grommets from the lower airbox remain in proper location on the vehicle
   

STEP 2:
Remove clamp on rubber inlet hose in shown location. *Depending on vehicle, this clamp may need to be cut
Remove the remaining stock hose from the vehicle With a cloth, protect the turbo opening so that no debris falls inside

STEP 3:
Remove the sensor from the airbox The sensor will be re-used. The screws will not

INSTALLATION OF DINAN SYSTEM

STEP 1:
Slide one clamp over the supplied Inlet Hose Fully seat the Inlet Hose against the stock turbo inlet housing Tighten clamp At this time, slide the other clamp onto the top and tighten slightly to hold into place. Final tightening will be completed once the Intake System is installed.

STEP 2:
Using the hardware shown below, mount the inlet tube to the airbox housing (3X)

Screw – Wave Washer – Flat Washer

STEP 3:
Once tightened, the inside of the box shall look like this

STEP 4:
Position the sensor on the inlet tube. This will only fit in one direction Use the remaining (2) M4x10 screws and tighten sensor to inlet tube as shown

STEP 5:
The filter shall have a supplied clamp in the box Slide the filter over the tube and proceed to STEP 6

STEP 6:
Ensure that the filter is in the correct orientation. The DINAN logo shall be upright when looking at the filter cap
Double check proper orientation by placing lid on box to ensure the filter does not interfere Tighten the Clamp

STEP 7:
[Image may not represent your vehicle, but the process is the same] Place the assembled intake into the vehicle. Slide Inlet Tube into Inlet Hose Snap the airbox into the rubber grommets to fully seat system The inlet tube shall protrude far enough into hose so that there is plenty of engagement of the clamp Tighten the Clamp

STEP 8:
Re-attach the sensor and lock

STEP 9:
Using the push rivets (5x), mount the lid to the lower box.
Ensure proper engagement THE INSTALLATION IS NOW COMPLETE. ENJOY!

OPTION 1:
If your vehicle has strut tower braces that need to be re-installed, place supplied spacer in location as shown prior to re-install of brace Repeat on driver side for uniform look If your vehicle does not have strut tower braces, please ignore this part

OR

OPTION 2:
Upgrade your stock brace with the DINAN STRUT TOWER BRACE. (D180-0013)
Your vehicle doesn’t have a brace? Upgrade your engine bay and handling with the DINAN STRUT TOWER BRACE KIT. (D180-0014) ENJOY!

Dinan Engineering
4800 US Hwy 280 West
Opelika, AL 36801
Phone: 800.341.5480

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>