ALPINE iLX-W670 7 Inch Audio Video Receiver User Guide
- June 13, 2024
- Alpine
Table of Contents
iLX-W670 7 Inch Audio Video Receiver
Product Information
The iLX-W670 is a 7-inch audio/video receiver. It is designed
for mobile 12V applications and should only be used in cars with a
12-volt negative ground. The device complies with Industry Canada’s
licence-exempt RSSs and is subject to certain regulations regarding
Bluetooth electromagnetic radiation.
Product Usage Instructions
-
Installation: It is important to install the
product correctly to ensure the driver cannot watch TV/video unless
the vehicle is stopped and the emergency brake is applied.
Incorrect installation may enable the driver to watch TV/video
while driving, which can be dangerous and may cause accidents. -
Watching Video: It is strictly prohibited to
watch video while driving as it can distract the driver from
looking ahead of the vehicle and may lead to accidents. Always
prioritize safe driving and avoid any activities that take your
attention away from driving. -
Operating Functions: Any function that
requires your prolonged attention should only be performed after
coming to a complete stop. Always find a safe location to stop your
vehicle before using these functions. Failure to do so may result
in accidents. -
Volume Control: Keep the volume at a level
where you can still hear outside noises while driving. Excessive
volume levels can obscure important sounds such as emergency
vehicle sirens or road warning signals, which can be dangerous.
Listening at loud volume levels in a car may also cause hearing
damage. -
Display Viewing: Minimize display viewing
while driving to avoid distractions. Viewing the display may divert
the driver’s attention from the road and increase the risk of
accidents. -
Disassembly and Alteration: Do not disassemble
or alter the product as it may result in accidents, fire, or
electric shock. -
Child Safety: Keep small objects such as
screws out of the reach of children. Swallowing them may result in
serious injury. If swallowed, consult a physician immediately. -
Replacing Fuses: When replacing fuses, ensure
you use the correct ampere rating. Failure to do so may result in
fire or electric shock. -
Vent and Radiator Panels: Do not block vents
or radiator panels as it may cause heat to build up inside and
result in fire. -
Proper Connections: Make sure to make the
correct connections as failure to do so may result in fire or
damage to the product.
For more detailed information on all functions, refer to the
Owner’s Manual published on the Alpine USA website. If needed, you can also
obtain a printout of the Owner’s Manual from an ALPINE dealer.
7-INCH AUDIO/VIDEO RECEIVER
iLX-W670
EN
FR
ES
QUICK REFERENCE GUIDE GUIDE DE RÉFÉRENCE RAPIDE GUÍA DE REFERENCIA RÁPIDA
Please register your product at www.alpine-usa.com/registration to protect
your purchase. Enregistrez-vous sur www.alpine-usa.com/registration pour
protéger votre achat. Registre su producto en la dirección www.alpine-
usa.com/registration para proteger su compra.
About the Rules of Bluetooth Electromagnetic Radiation Regulation
USA/Canada
FCC/IC CAUTION This device complies with Industry Canada’s licence-exempt
RSSs. Operation is subject to the following two conditions: (1) This device
may not cause interference; and (2) This device must accept any interference,
including interference that may cause
undesired operation of the device. Changes or modifications not expressly
approved by the party responsible for compliance could void the user’s
authority to operate the equipment. This equipment complies with FCC/IC
radiation exposure limits set forth for an uncontrolled environment and meets
the FCC radio frequency (RF) Exposure Guidelines and RSS-102 of the IC radio
frequency (RF) Exposure rules. This equipment has very low levels of RF energy
that it deemed to comply without maximum permissive exposure evaluation (MPE).
But it is desirable that it should be installed and operated keeping the
radiator at least 20 cm or more away from person’s body.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux
appareils radio exempts de licence. L’exploitation est autorisée aux deux
conditions suivantes : (1) l’appareil ne doit pas produire de brouillage; (2)
l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique
subi, même
si le brouillage est susceptible d’en compromettre le fonctionnement. Cet
équipement est conforme aux limites d’exposition aux rayonnements énoncées
pour un environnement non contrôlé et respecte les règles les radioélectriques
(RF) de la FCC lignes directrices d’exposition et d’exposition aux fréquences
radioélectriques (RF) CNR-102 de l’IC. Cet équipement émet une énergie RF très
faible qui est considérée conforme sans évaluation de l’exposition maximale
autorisée (MPE). Cependant, il est souhaitable qu’il devrait être installé et
utilisé en gardant une distance de 20 cm ou plus entre le radiateur et le
corps humain.
Contents
WARNING …………………………………………………………………………………………………………………………………………….2 CAUTION
…………………………………………………………………………………………………………………………………………….. 3 Getting Started
…………………………………………………………………………………………………………………………………..4 Apple CarPlay Operation
(Optional)………………………………………………………………………………………………..6 Android AutoTM
(Optional)…………………………………………………………………………………………………………………6 Radio Operation
…………………………………………………………………………………………………………………………………7 USB Flash drive Operation
(Optional)……………………………………………………………………………………………..7 SiriusXM® Satellite Radio
Operation (Optional) ……………………………………………………………………………. 8 iPod mode on iPhone
(Optional)……………………………………………………………………………………………………..9 Hands-Free Phone Control
……………………………………………………………………………………………………………..10 Camera Operation (Optional)
…………………………………………………………………………………………………………11 Installation
…………………………………………………………………………………………………………………………………………12 Connections
………………………………………………………………………………………………………………………………………14 Specifications
……………………………………………………………………………………………………………………………………16
IMPORTANT
Please record the serial number of your unit in the space provided below and
keep it as a permanent record.
SERIAL NUMBER: INSTALLATION DATE: INSTALLATION TECHNICIAN: PLACE OF PURCHASE:
For details on all functions, refer to the Owner’s Manual published on our
website at http:// www.alpine-usa.com. If required, an ALPINE dealer will
readily provide you with a print out of the Owner’s Manual published on the
website.
1-EN
WARNING
WARNING
This symbol means important instructions. Failure to heed them can result in
serious injury or death.
INSTALL THE PRODUCT CORRECTLY SO THAT THE DRIVER CANNOT WATCH TV/VIDEO UNLESS
THE VEHICLE IS STOPPED AND THE EMERGENCY BRAKE IS APPLIED. It is dangerous for
the driver to watch TV/Video while driving a vehicle. Installing this product
incorrectly enables the driver to watch TV/Video while driving. This may cause
a distraction, preventing the driver from looking ahead, thus causing an
accident. The driver or other people could be severely injured.
DO NOT WATCH VIDEO WHILE DRIVING. Watching the video may distract the driver
from looking ahead of the vehicle and cause an accident.
DO NOT OPERATE ANY FUNCTION THAT TAKES YOUR ATTENTION AWAY FROM SAFELY DRIVING
YOUR VEHICLE. Any function that requires your prolonged attention should only
be performed after coming to a complete stop. Always stop the vehicle in a
safe location before performing these functions. Failure to do so may result
in an accident.
KEEP THE VOLUME AT A LEVEL WHERE YOU CAN STILL HEAR OUTSIDE NOISES WHILE
DRIVING. Excessive volume levels that obscure sounds such as emergency vehicle
sirens or road warning signals (train crossings, etc.) can be dangerous and
may result in an accident. LISTENING AT LOUD VOLUME LEVELS IN A CAR MAY ALSO
CAUSE HEARING DAMAGE.
MINIMIZE DISPLAY VIEWING WHILE DRIVING. Viewing the display may distract the
driver from looking ahead of the vehicle and cause an accident.
DO NOT DISASSEMBLE OR ALTER. Doing so may result in an accident, fire or
electric shock.
USE ONLY IN CARS WITH A 12 VOLT NEGATIVE GROUND. (Check with your dealer if
you are not sure.) Failure to do so may result in fire, etc.
KEEP SMALL OBJECTS SUCH AS SCREWS OUT OF THE REACH OF CHILDREN. Swallowing
them may result in serious injury. If swallowed, consult a physician
immediately.
USE THE CORRECT AMPERE RATING WHEN REPLACING FUSES. Failure to do so may
result in fire or electric shock.
DO NOT BLOCK VENTS OR RADIATOR PANELS. Doing so may cause heat to build up
inside and may result in fire.
USE THIS PRODUCT FOR MOBILE 12V APPLICATIONS. Use for other than its designed
application may result in fire, electric shock or other injury.
MAKE THE CORRECT CONNECTIONS. Failure to make the proper connections may
result in fire or product damage.
BEFORE WIRING, DISCONNECT THE CABLE FROM THE NEGATIVE BATTERY TERMINAL.
Failure to do so may result in electric shock or injury due to electrical
shorts.
DO NOT ALLOW CABLES TO BECOME ENTANGLED IN SURROUNDING OBJECTS. Arrange wiring
and cables in compliance with the manual to prevent obstructions when driving.
Cables or wiring that obstruct or hang up on places such as the steering
wheel, gear lever, brake pedals, etc. can be extremely hazardous.
DO NOT SPLICE INTO ELECTRICAL CABLES. Never cut away cable insulation to
supply power to other equipment. Doing so will exceed the current carrying
capacity of the wire and result in fire or electric shock.
DO NOT DAMAGE PIPE OR WIRING WHEN DRILLING HOLES. When drilling holes in the
chassis for installation, take precautions so as not to contact, damage or
obstruct pipes, fuel lines, tanks or electrical wiring. Failure to take such
precautions may result in fire.
DO NOT USE BOLTS OR NUTS IN THE BRAKE OR STEERING SYSTEMS TO MAKE GROUND
CONNECTIONS. Bolts or nuts used for the brake or steering systems (or any
other safety-related system), or tanks should NEVER be used for installations
or ground connections. Using such parts could disable control of the vehicle
and cause fire etc.
DO NOT INSTALL IN LOCATIONS WHICH MIGHT HINDER VEHICLE OPERATION, SUCH AS THE
STEERING WHEEL OR GEARSHIFT. Doing so may obstruct forward vision or hamper
movement etc. and results in serious accident.
2-EN
CAUTION
This symbol means important instructions. Failure to heed them can result in
injury or material property damage.
HALT USE IMMEDIATELY IF A PROBLEM APPEARS. Failure to do so may cause personal
injury or damage to the product. Return it to your authorized Alpine dealer or
the nearest Alpine Service Center for repairing. HAVE THE WIRING AND
INSTALLATION DONE BY EXPERTS. The wiring and installation of this unit
requires special technical skill and experience. To ensure safety, always
contact the dealer where you purchased this product to have the work done. USE
SPECIFIED ACCESSORY PARTS AND INSTALL THEM SECURELY. Be sure to use only the
specified accessory parts. Use of other than designated parts may damage this
unit internally or may not securely install the unit in place. This may cause
parts to become loose resulting in hazards or product failure. ARRANGE THE
WIRING SO IT IS NOT CRIMPED OR PINCHED BY A SHARP METAL EDGE. Route the cables
and wiring away from moving parts (like the seat rails) or sharp or pointed
edges. This will prevent crimping and damage to the wiring. If wiring passes
through a hole in metal, use a rubber grommet to prevent the wire’s insulation
from being cut by the metal edge of the hole. DO NOT INSTALL IN LOCATIONS WITH
HIGH MOISTURE OR DUST. Avoid installing the unit in locations with high
incidence of moisture or dust. Moisture or dust that penetrates into this unit
may result in product failure.
3-EN
Getting Started
Owner’s manual
Location of Controls, Turning Power On or Off
Controls Position
The screen design used in the Quick Reference Guide may differ from the actual
screen.
/ (DOWN/UP) button Touch to adjust the volume. Touch and hold this button for
at least 1.7 second to adjust the volume to maximum or minimum.
(MUTE) button Touch to activate/deactivate the mute mode. Touch and hold this
button for at least 1.7 second to display on/off.
(HOME)/(Power Off) button Activates the HOME screen. Touch and hold this
button for at least 1.7 second to turn the power off.
(Phone) button Activates the Phone screen.
button
When phone is connected to CarPlay, touch this button to activate Siri. When
phone is connected to Android Auto, touch this button to activate VR. When
Siri is activated, the function of Siri is available When VR is activated, the
VR setting is ON and the function of VR is available. When the CarPlay/Android
Audio is disconnected, the operation in this button is invalidate. When
CarPlay/Android Audio is disconnected, touch and long hold to enter into the
Device Searching List to activate the new device searching.
(Reset) button
Reset & Restart.
4-EN
Turning Power On or Off
1 Turn the ignition key to the ACC or ON position.
The system is turned on.
2 Touch and hold the (HOME) button for at least 1.7 seconds to turn the power
off.
· When the system is used for the first time, the language selection menu is
displayed. Select the desired language, and then touch [OK].
About the HOME Screen
Select a widget on the HOME screen to perform various settings and operations
of the function.
1 Touch the (HOME) button.
The HOME screen is displayed. HOME screen example
Radio Apple CarPlay Android Auto USB iPod SiriusXM Bluetooth Audio Phone AUX Camera
Displays the Radio main screen.
You can use Apple CarPlay. · If compatible iPhone is not connected to usb,
this widget is not available.
You can use Android Auto. · If compatible Android phone is not connected to
usb, this widget is not available.
You can play back music files, video files and photo files stored in a USB
flash drive. · If a USB flash drive is not connected, this widget is not
available.
Displays the iPod main screen. · If an iPhone is not connected, this widget is
not available.
Displays the SiriusXM main screen. · If a SiriusXM Tuner (Optional) is not
connected, this widget is not available.
Displays the Bluetooth audio main screen.
Displays the Phone main screen.
Displays the AUX main screen. · If there is no input signal on AUX, it will be
a black screen.
Displays the Camera main screen. · If there is no input signal on Camera, it
will be a black screen.
5-EN
Owner’s manual
Apple CarPlay Operation (Optional)
Apple CarPlay (Optional)
Apple CarPlay is a smarter, safer way to use your iPhone in the car. Apple
CarPlay takes the things you want to do with your iPhone while driving and
puts them right on this unit. You can get directions, make calls, send and
receive messages, and listen to music, all in a way that allows you to stay
focused on the road. Just plug in your iPhone to this unit and go.
1 Touch the (HOME) button.
The HOME screen is displayed.
2 Touch [Apple CarPlay].
The Apple CarPlay screen is displayed.
· Refer to “Apple CarPlay” in the Owner’s Manual for information on how to
operate Apple CarPlay.
Android AutoTM (Optional)
Owner’s manual
Android AutoTM (Optional)
Android Auto is designed to make it easier to use apps from your phone while
you’re on the road. Navigate with Google Maps, listen to Playlists or Podcasts
from your favorite apps, send messages via voice, and more. Download the
Android Auto App from the Google Play Store before continuing.
1 Touch the (HOME) button.
The HOME screen is displayed.
2 Touch [Android Auto].
The Android Auto screen is displayed.
· Refer to “Android Auto” in the Owner’s Manual for information on how to
operate Android Auto.
6-EN
Radio Operation
Owner’s manual
Radio
Band button Switches a band.
Band button Switches a band.
Touch [ ] [ ] to select the station seek up or seek down respectively
Touch [ ] [ ] to change the radio frequency up or down respectively · Operate
in manual mode
Preset button Displays the preset stations with a short touch. Touch for at
least 1.5. second to memorise the current station as a preset station.
Plays each preset station for about 10 seconds
Scan and memorises active stations automatically
Switch Local mode/Manual mode/DX mode
· The patterns of some keys in the Quick Reference Guide may differ from the actual screen.
Owner’s manual
USB Flash drive Operation (Optional)
USB Flash drive Operation (Optional)
You can play back music files (WAVE.WMA.AAC.MP3.OGG.FLAC.APE), video files
(AVI, MPEG 1/2, MPEG4, WMV, Flash, QuickTime, ASF, Matroska Video, TS Stream,
3GP) and photo files (JPG, JPEG, PNG, BMP) stored in a USB flash drive on the
internal player of this system.
USB Audio main screen example
Artwork display
Information display
Elapsed time/Total time for playing
Finds the beginning of the current file/Finds a previous file within 1 second
after playback starts/Fast-reverses when touched for at least 2 second
Finds the beginning of the next file/Fast-forwards when touched for at least 2
seconds
Displays the USB List screen
Shuffle mode
[ ] repeat_off, [ ] repeat_folder, [ ] repeat_one, [ ] repeat_all
Pause and Play
· The patterns of some keys in the Quick Reference Guide may differ from the
actual screen.
7-EN
Owner’s manual
SiriusXM Satellite Radio Operation (Optional)
SiriusXM® Satellite Radio Operation (Optional)
When an optional SiriusXM Tuner is connected to this unit, the following
operations may be performed.
SiriusXM main screen example
Band button Switches a band.
Information display channel name, Artist Basic, Song Basic, Cat name
Tune Select the specified channel manually
Preset buttons Displays the preset channels with a short touch. Touch for at
least 1.5 second to memorize the current channel as a preset channel. Select
the channel number
Changes to the previous channel
Displays the SiriusXM setup screen
Changes to the next channel
· The patterns of some keys in the Quick Reference Guide may differ from the
actual screen.
Displays the SiriusXM List screen
All channel: Displays all channel
Category: Select channel category
Tune: Select the specified channel manually
8-EN
Owner’s manual
iPod mode on iPhone (Optional)
iPod mode on iPhone (Optional)
Before using this function, plug in your iPhone using a Lightning-USB cable
(supplied with iPhone) to the unit.
The following devices have been tested and shown to work with this unit.
Correct function of earlier versions cannot be guaranteed.
iPhone 14 Pro Max, iPhone 14 Pro, iPhone 14 Plus, iPhone 14, iPhone SE (3rd
generation), iPhone 13 Pro Max, iPhone 13 Pro, iPhone 13, iPhone 13 mini,
iPhone 12 Pro Max, iPhone 12 Pro, iPhone 12, iPhone 12 mini, iPhone SE (2nd
generation), iPhone 11 Pro Max, iPhone 11 Pro, iPhone 11, iPhone XS Max,
iPhone XS, iPhone XR, iPhone X, iPhone 8 Plus, iPhone 8, iPhone 7 Plus, iPhone
7, iPhone SE, iPhone 6s Plus, iPhone 6s, iPhone 6 Plus, iPhone 6
iPod main screen example
Artwork display
Elapsed time/Total time for playing Repeat mode Finds the beginning of the
current file/Finds a previous file within 1 second after playback starts/Fast-
reverses when touched for at least 2 second
Finds the beginning of the next file/Fast-forwards when touched for at least 2
seconds
Searching for a Music File
For example: Searching by Artist name
1 Touch [ (Search)] during playback. 2 Touch [Artists].
Information display Podcasts mode.
Displays the Music Files screen Shuffle mode [ ] repeat_off, [ ] repeat_one, [
] repeat_all Pause and Play
3 Touch the desired artist’s name.
4 Touch the desired album’s name. 5 Touch the desired song’s name.
The selected song is played back.
9-EN
Owner’s manual
Hands-Free Phone Control
Bluetooth Setup, Bluetooth Operation
The unit can connect with up to two hands-free phones.
How to connect to a Bluetooth
6
compatible device (Pairing)
The device registration is complete.
To display the Setup HOME screen: 1. Bring your vehicle to a complete stop at
a safe location.
Engage the parking brake. 2. Release the parking brake. (For safety, release
the
parking brake while depressing the foot brake pedal). 3. Engage the parking
brake again. · For automatic transmission vehicles, place the
transmission lever in the Park position.
1 Touch the (HOME) button.
The HOME screen is displayed.
2 Touch [Bluetooth Audio].
· You can register up to 5 Bluetooth compatible mobile phones.
· The Bluetooth registration process differs depending on the device version
and SSP (Simple Secure Pairing). If a 4 or 6 character Numeric Comparison
appears on this system, enter the Numeric Comparison on the Bluetooth device.
· If a 6 character Passkey appears on this system, make sure the same passkey
is displayed on the Bluetooth device, and follow the screen.
Answering a Call
3 Touch [ ].
1 An incoming call triggers the ringtone and
an incoming call display.
4
Touch [ (Search)] to search for a new device.
2
Touch [ ] (Call).
The call starts.
5 Touch the device you want to connect from the list.
Hanging up the Telephone
1 Touch [ ] (End Call).
The call finishes.
10-EN
Calling
Entering a Phone Number to Make a Call
1 Touch [Keypad].
The number input screen (Keypad) appears.
2 Touch the name of the contact or number
you want to call. The phone call is started.
Calling from the Contacts list (Phone Book)
Touch [ ] to delete an entered number.
2 Enter the phone number you wish to call.
· You can enter up to 20 digits.
3 Touch [ ] (Call).
The phone call is started.
Making a phone call from the Recent Events list
1 Touch [ ] to change to the Recent Events
list screen.
1 Touch [ ] to change to the Contacts list
screen.
2 Touch the name of the contact or number
you want to call.
3 Touch the phone number.
The Phone Operation screen is displayed.
4 Touch the number you want to call.
The phone call is started.
Camera Operation (Optional)
Owner’s manual
Camera Operation (Optional)
Displaying the Camera Image from the Menu screen
1 Touch the (HOME) button.
The HOME screen is displayed.
2 Touch [Camera].
Touch the screen while the camera image is being displayed, and touch [ ] to
return to the main source screen or previous screen.
11-EN
Installation
Note on installation · Install at an angle between horizontal and 30°.
Note that installing at an angle outside of this range will result in a loss
of performance and possible damage.
Owner’s manual
Installation
Microphone
Cable clamp (sold separately)
0 – 30°
· Do not block the unit’s heat sink, which would prevent air circulation. If
blocked, heat will accumulate inside the unit and may cause a fire.
Heat sink
Installing the Unit
1 Mount the original mounting bracket to
the unit using the supplied screws.
Original Mounting Bracket
Screws (M5 × 8) (included)
Rear of the Unit
Mounting the Microphone
For safe use, make sure of the following: · Location is stable and firm. ·
Driver’s view and operations are not obstructed. · Microphone is located where
the driver’s voice can
be easily picked up (on the sun visor, etc.).
When you speak into the microphone, you should not have to change your driving
posture. This may cause a distraction, taking your attention away from safely
driving your vehicle. Carefully consider direction and distance while mounting
the microphone. Confirm that the driver’s voice can be easily picked up at the
selected location.
Ground Lead*
The original mounting bracket is not included with the product.
Chassis
2 Connect all other leads of the unit
according to details described in the “Connections” (page 14).
3 Mounting the unit in a car.
To securely connect the ground lead, use an already installed screw on a metal
part of the vehicle (marked ( )) or a clean, bare metal spot on the vehicle’s
chassis.
· Fix the cables carefully. Do not damage them by tucking them into movable
parts, such as a seat rail, or by locating them against sharp or pointed
edges.
12-EN
Connection Diagram of SPST Switch (sold separately)
(If the ACC power supply is not available)
iLX-W670
ACC (Red)
BATTERY (Yellow)
SPST SW (Optional)
FUSE (5A) (Optional)
FUSE (20A) (Optional)
Battery
· If your vehicle has no ACC power supply, add an SPST (Single-Pole, Single-
Throw) switch (sold separately) and fuse (sold separately).
· The diagram and the fuse amperage shown above are in the case when iLX-W670
is used individually. · If the switched power (ignition) lead of the iLX-W670
is connected directly to the positive (+) post of the vehicle’s battery,
the iLX-W670 draws some current (several hundred milliamperes) even when its
switch is placed in the OFF position, and the battery may be discharged.
13-EN
Connections
Owner’s manual
Connections
14-EN
Radio Antenna Receptacle
GPS Antenna Receptacle
Power Antenna Lead (Blue) Connect this lead to the +B terminal of your power
antenna, if applicable. · This lead should be used only for controlling the
vehicle’s power antenna. Do not use this lead to turn on an amplifier or a
signal processor, etc.
Remote Turn-On Lead (Blue/White) Connect this lead to the remote turn-on lead
of your amplifier or signal processor.
Parking Brake Lead (Yellow/Blue) Connect this lead to the power supply side of
parking brake switch to transmit the parking brake status signals to the unit.
Reverse Lead (Violet/White)
Right Rear (+) Speaker Output Lead (Violet)
Right Rear () Speaker Output Lead (Violet/Black)
Right Front (+) Speaker Output Lead (Gray)
Right Front () Speaker Output Lead (Gray/Black)
Left Front (+) Speaker Output Lead (White)
Left Front () Speaker Output Lead (White/Black)
Left Rear (+) Speaker Output Lead (Green)
Left Rear () Speaker Output Lead (Green/Black)
Switched Power Lead (Ignition) (Red) Connect this lead to an open terminal on
the vehicle’s fuse box or another unused power source that provides (+) 12V
only when the ignition is turned on or in the accessory position.
Fuse Holder (15A)
Battery Lead (Yellow) Connect this lead to the positive (+) post of the
vehicle’s battery.
Ground Lead (Black) Connect this lead to a good chassis ground on the vehicle.
Make sure the connection is made to bare metal and is securely fastened using
the sheet metal screw provided.
SPEED SENSOR (Green/White)
LIGHTING LINK (Brown)
SW1 (Black/Brown) Steering Wheel Control
SW2 (Black/Blue) Steering Wheel Control SWG (Black/White) Steering Wheel GND
REAR CAMERA Input RCA Connector (Black) Use when connecting a camera with RCA
Output Connector. Rear Output RCA Connectors Can be used as Rear Output RCA
Connectors. RED is right and WHITE is left. Front Output RCA Connectors Can be
used as Front Output RCA Connectors. RED is right and WHITE is left. Subwoofer
RCA Connectors AUX INPUT (Black) Audio and video input. MIC Input Connector To
microphone (included) SiriusXM Tuner Input Connector To SiriusXM Tuner (sold
separately). · For more information on how to install the SiriusXM
Connect Vehicle tuner, consult the installation guide included with the tuner.
USB Connector To USB flash drive, iPhone or Android smartphone. Power Supply
Connector CAMERA/SWC PRE OUT/AUX
15-EN
Specifications
Owner’s manual
Specifications
MONITOR SECTION
Screen Size
6.75″
LCD Type
Normally white, Transmissive
Operation System
a-Si TFT active matrix
Number of Picture Elements 1152000 pcs.
(800 × 480 × 3(RGB))
Effective Number of Picture Elements
99% or more
Illumination System
LED
FM TUNER SECTION
Tuning Range Mono Usable Sensitivity 50 dB Quieting Sensitivity
87.7 107.9 MHz <9 dBu (75 ohms) <5 dBu (75 ohms)
Signal-to-Noise Ratio Stereo Separation
65 dB 35 dB
AM TUNER SECTION
Tuning Range Usable Sensitivity
530 1,710 kHz 34 dBu
USB SECTION
USB requirements Max. Power Consumption USB Class
File System Number of Channels Frequency Response*1 Total Harmonic Distortion
Dynamic Range Signal-to-Noise Ratio Channel Separation
USB 2.0 1,500 mA (CDP Support) USB (Play From Device)/ USB (Mass Storage Class) FAT16/32, NTFS 2-Channels (Stereo) 17 20,000 Hz (±1 dB) 0.05% (at 1 kHz) 90 dB (at 1 kHz) 85 dB 75 dB (at 1 kHz)
1 Frequency response may differ depending on the encoder software/bit rate.
Bluetooth SECTION
Bluetooth Specification Output Power Profile
Bluetooth V5.0 <+4dBm Ave. (Power class 2) HFP (Hands-Free Profile) PBAP (Phone Book Access Profile) A2DP (Advanced Audio Distribution Profile) AVRCP (Audio/Video Remote Control Profile)
GENERAL
Power Requirement Operating temperature Power Output
14.4 V DC (10.815.1 V allowable) -4°F to +140°F (-20°C to + 60°C) 16 W RMS × 4*2
2 Primary amplifier ratings per CEA-2006 Standard · Power output: measured at 4 Ohms and 1% THD+N · S/N: 80 dBA (reference: 1 W into 4 Ohms)
Weight Audio output level
Preout (Front, Rear): Preout (Subwoofer):
0.9 kg
4V/10k ohms (max.) 4V/10k ohms (max.)
CHASSIS SIZE
Width Height Depth
178 mm 100 mm 68mm
· Due to continuous product improvement, specifications
and design are subject to change without notice. · The LCD panel is manufactured using an extremely high
precision manufacturing technology. Its effective pixel
ratio is over 99.99%. This means that there is a
possibility that 0.01% of the pixels could be either always
ON or OFF.
· Windows Media and the Windows logo are trademarks, or registered trademarks
of Microsoft Corporation in the United States and/or other countries.
· Apple, iPhone, iPod, and Siri are trademarks of Apple Inc., registered in
the U.S. and other countries. Apple CarPlay is a trademark of Apple Inc.
· Use of the Made for Apple and Works with Apple badges means that an
accessory has been designed to connect specifically to the Apple product(s)
identified in the Made for Apple badge and to work specifically with the
technology identified in the Works with Apple badge, and has been certified by
the developer to meet Apple performance standards. Apple is not responsible
for the operation of this device or its compliance with safety and regulatory
standards.
· Please note that the use of this accessory with an Apple product may affect
wireless performance.
· Use of the Apple CarPlay logo means that a vehicle user interface meets
Apple performance standards. Apple is not responsible for the operation of
this vehicle or its compliance with safety and regulatory standards. Please
note that the use of this product with iPhone may affect wireless performance.
16-EN
· SiriusXM and all related marks and logos are trademarks of Sirius XM Radio
Inc. All rights reserved.
· Google, Android, Android Auto, Google Play and other marks are trademarks of
Google LLC.
· The Bluetooth® word mark and logos are registered trademarks owned by the
Bluetooth SIG, Inc. and any use of such marks by Alpine Electronics, Inc. is
under license.
· MPEG Layer-3 audio coding technology licensed from Fraunhofer IIS and
Thomson. Supply of this product only conveys a license for private, non-
commercial use and does not convey a license nor imply any right to use this
product in any commercial (i.e. revenue-generation) real time broadcasting
(terrestrial, satellite, cable and/or any other media), broadcasting/streaming
via internet, intranets and/ or other networks or in other electronic content
distribution systems, such as pay-audio or audio-ondemand applications. An
independent license for such use is required. For details, please visit
http://www.mp3licensing.com
GARANTIE LIMITÉE
Fidèle à son engagement de ne fournir que des produits de qualité, ALPINE
ÉLECTRONIQUE DE L’AMÉRIQUE, INC. (« Alpine ») est heureuse de vous offrir
cette garantie. Nous vous suggérons de le lire attentivement et en entier. Si
vous avez la moindre question, veuillez contacter l’un de nos concessionnaires
ou appeler directement Alpine aux numéros listés ci-dessous.
PRODUITS COUVERTS PAR LA GARANTIE
Cette garantie couvre les produits audio de voiture et les accessoires
connexes (« le produit »). Elle ne couvre les produits que dans le pays où ils
ont été achetés.
DURÉE DE LA GARANTIE
Cette garantie est en vigueur pendant un an à partir de la date du premier
achat du client.
PERSONNES PROTÉGÉES PAR LA GARANTIE
Seul l’acheteur original du produit, s’il résisde aux États-Unis, à Porto Rico
ou au Canada, peut se prévaloir de la garantie.
CE QUI EST COUVERT
Cette garantie couvre tous les défauts de matériaux et de fabrication (pièces
et main d’oeuvre) du produit.
CE QUI N’EST PAS COUVERT
Cette garantie ne couvre pas ce qui suit: Les dommages survenus durant le
transport des produits renvoyés à Alpine pour être réparés (les réclamations
doivent être adressées au transporteur); Les dégâts provoqués par un accident
ou une mauvaise utilisation, y compris des bobines acoustiques grillées suite
à une surexcitation des enceintes (augmentation du niveau de l’amplificateur
jusqu’à atteindre un effet de distorsion ou d’écrêtage), une défaillance
mécanique des enceintes (perforations, déchirures ou fentes), panneaux LCD
fissurés ou endommagés, disques durs endommagés ou ayant subi une chute. Tout
dégât provoqué par négligence, usage inapproprié, mauvaise utilisation ou par
le non-respect des instructions indiquées dans le manuel de l’utilisateur. Les
dommages dus à la force majeure, notamment aux tremblements de terre, au feu,
aux inondations, aux tempêtes ou aux autres cataclysmes naturels; Les frais ou
les dépenses relatifs à l’enlèvement ou à la réinstallation du produit; Les
services rendus par une personne, physique ou morale non autorisée; Les
produits dont le numéro de série a été effacé, modifié ou retiré; Les produits
qui ont été adaptés ou modifiés sans le consentement d’Alpine; Les produits
qui ne sont pas distribués par Alpine aux Etats-Unis, à Porto Rico ou au
Canada; Les produits qui n’ont pas été achetés par l’entremise d’un
concessionnaire Alpine autorisé;
COMMENT SE PRÉVALOIR DE LA GARANTIE
Il vous faut remettre le produit nécessitant des réparations à un centre de
service autorisé Alpine ou à Alpine même et en assumer les frais de transport.
Alpine a le choix entre réparer le produit ou le remplacer par un produit neuf
ou révisé, le tout sans frais pour vous. Si les réparations sont couvertes par
la garantie et si le produit a été envoyé à un centre de service Alpine ou à
Alpine, le paiement des frais de réexpédition du produit incombe Alpine.
Vous devez donner une description détaillée des problèmes qui sont à l’origine
de votre demande de réparation. Vous devez joindre la preuve de votre achat du
produit. Vous devez emballer soigneusement le produit pour éviter tout dommage
durant son transport. Pour éviter la perte de l’envoi, il est conseillé de
choisir un transporteur qui propose un service de suivi des envois.
LIMITATION DES GARANTIES TACITES
LA DURÉE DE TOUTES LES GARANTIES TACITES, Y COMPRIS LA GARANTIE D’ADAPTATION À
L’UTILISATION ET LA GARANTIE DE QUALITÉ LOYALE ET MARCHANDE, EST LIMITÉE À
CELLE DE LA GARANTIE EXPRESSE DÉTERMINÉE CI-DESSUS. PERSONNE N’EST AUTORISÉ À
ENGAGER AUTREMENT LA RESPONSABILITÉ D’ALPINE EN VERTU DE LA VENTE D’UN
PRODUIT.
EXCLUSIONS DE LA GARANTIE
ALPINE STIPULE EXPRESSÉMENT QU’ELLE N’EST PAS RESPONSABLE DES DOMMAGES-
INTÉRÊTS ET DOMMAGES INDIRECTS PROVOQUÉS PAR LE PRODUIT. LES DOMMAGES-INTÉRÊTS
SONT LES FRAIS DE TRANSPORT DU PRODUIT VERS UN CENTRE DE SERVICE ALPINE, LA
PERTE DE TEMPS DE L’ACHETEUR ORIGINAL, LA PERTE D’UTILISATION DU PRODUIT, LES
BILLETS D’AUTOBUS, LA LOCATION DE VOITURES ET TOUS LES AUTRES FRAIS LIÉS À LA
GARDE DU PRODUIT. LES DOMMAGES INDIRECTS SONT LES FRAIS DE RÉPARATION OU DE
REMPLACEMENT D’AUTRES BIENS ENDOMMAGÉS SUITE AU MAUVAIS FONCTIONNEMENT DU
PRODUIT. LES RECOURS PRÉVUS PAR LES PRÉSENTES EXCLUENT ET REMPLACENT TOUTE
AUTRE FORME DE RECOURS.
LIEN ENTRE LA GARANTIE ET LA LOI
La garantie vous donne des droits spécifiques, mais vous pouvez aussi jouir
d’autres droits, qui varient d’un état ou d’une province à l’autre. En outre,
certains états et certaines provinces interdisent de limiter la durée des
garanties tacites ou d’exclure les dommages accessoires ou indirects. Dans ce
cas, les limites et les exclusions de la garantie peuvent ne pas s’appliquer à
vous.
CLAUSE APPLICABLE AU CANADA SEULEMENT
Pour que la garantie soit valable, il faut qu’un centre d’installation
autorisé ait installé le système audio pour l’auto dans votre véhicule et
qu’il ait ensuite apposé son cachet sur la garantie.
NUMÉROS D’APPEL DU SERVICE À LA CLIENTÈLE
Si vous avez besoin de nos services, veuillez appeler Alpine aux numéros ci-
dessous pour le centre de service autorisé Alpine le plus proche.
AUDIO DE VOITURE 1-800-ALPINE-1 (1-800-257-4631)
NAVIGATION
1-888-NAV-HELP (1-888-628-4357)
Ou visitez notre site Web à l’adresse http://www.alpine-usa.com
ALPINE ÉLECTRONIQUE DE L’AMÉRIQUE, INC., 1500 Atlantic Blvd, Auburn Hills, Michigan 48326, U.S.A. N’envoyez aucun produit à ces adresses. Appelez notre numéro gratuit ou visitez notre site Web si vous recherchez un centre de service.
LIMITED WARRANTY
ALPINE ELECTRONICS OF AMERICA, INC. (“Alpine”), is dedicated to quality
craftsmanship and are pleased to offer this Warranty. We suggest that you read
it thoroughly. Should you have any questions, please contact your Dealer or
contact Alpine at one of the telephone numbers listed below.
PRODUCTS COVERED:
This Warranty covers Car Audio Products and Related Accessories (“the
product”). Products purchased in the Canada are covered only in the Canada.
Products purchased in the U.S.A. are covered only in the U.S.A.
LENGTH OF WARRANTY:
This Warranty is in effect for one year from the date of the first consumer
purchase.
WHO IS COVERED:
This Warranty only covers the original purchaser of the product, who must
reside in the United States, Puerto Rico or Canada.
WHAT IS COVERED:
This Warranty covers defects in materials or workmanship (parts and labor) in
the product.
WHAT IS NOT COVERED:
This Warranty does not cover the following: Damage occurring during shipment
of the product to Alpine for repair (claims must be presented to the carrier).
Damage caused by accident or abuse, including burned voice coils caused by
over-driving the speaker (amplifier level is turned up and driven into
distortion or clipping). Speaker mechanical failure (e.g. punctures, tears or
rips). Cracked or damaged LCD panels. Dropped or damaged hard drives. Damage
caused by negligence, misuse, improper operation or failure to follow
instructions contained in the Owner’s manual. Damage caused by act of God,
including without limitation, earthquake, fire, flood, storms or other acts of
nature. Any cost or expense related to the removal or reinstallation of the
product. Service performed by an unauthorized person, company or association.
Any product which has the serial number defaced, altered or removed. Any
product which has been adjusted, altered or modified without Alpine’s consent.
Any product not distributed by Alpine within the United States, Puerto Rico or
Canada. Any product not purchased from an Authorized Alpine Dealer.
HOW TO OBTAIN WARRANTY SERVICE:
You are responsible for delivery of the product to an Authorized Alpine
Service Center or Alpine for repair and for payment of any initial shipping
charges. Alpine will, at its option, repair or replace the product with a new
or reconditioned product without charge. If the repairs are covered by the
warranty, and if the product was shipped to an Authorized Alpine Service
Center or Alpine, Alpine will pay the return shipping charges. You should
provide a detailed description of the problem(s) for which service is
required. You must supply proof of your purchase of the product. You must
package the product securely to avoid damage during shipment. To prevent lost
packages it is recommended to use a carrier that provides a tracking service.
HOW WE LIMIT IMPLIED WARRANTIES:
ANY IMPLIED WARRANTIES INCLUDING FITNESS FOR USE AND MERCHANTABILITY ARE
LIMITED IN DURATION TO THE PERIOD OF THE EXPRESS WARRANTY SET FORTH ABOVE AND
NO PERSON IS AUTHORIZED TO ASSUME FOR ALPINE ANY OTHER LIABILITY IN CONNECTION
WITH THE SALE OF THE PRODUCT.
HOW WE EXCLUDE CERTAIN DAMAGES:
ALPINE EXPRESSLY DISCLAIMS LIABILITY FOR INCIDENTAL AND CONSEQUENTIAL DAMAGES
CAUSED BY THE PRODUCT. THE TERM “INCIDENTAL DAMAGES” REFERS TO EXPENSES OF
TRANSPORTING THE PRODUCT TO THE ALPINE SERVICE CENTER, LOSS OF THE ORIGINAL
PURCHASER’S TIME, LOSS OF THE USE OF THE PRODUCT, BUS FARES, CAR RENTALS OR
OTHERS COSTS RELATING TO THE CARE AND CUSTODY OF THE PRODUCT. THE TERM
“CONSEQUENTIAL DAMAGES” REFERS TO THE COST OF REPAIRING OR REPLACING OTHER
PROPERTY WHICH IS DAMAGED WHEN THIS PRODUCT DOES NOT WORK PROPERLY. THE
REMEDIES PROVIDED UNDER THIS WARRANTY ARE EXCLUSIVE AND IN LIEU OF ALL OTHERS.
HOW STATE/PROVINCIAL LAW RELATES TO THE WARRANTY:
This Warranty gives you specific legal rights, and you may also have other
rights which vary from state to state and province to province. In addition,
some states/provinces do not allow limitations on how long an implied warranty
lasts, and some do not allow the exclusion or limitation of incidental or
consequential damages. Accordingly, limitations as to these matters contained
herein may not apply to you.
IN CANADA ONLY:
This Warranty is not valid unless your Alpine car audio product has been
installed in your vehicle by an Authorized Installation Center, and this
warranty stamped upon installation by the installation center.
HOW TO CONTACT CUSTOMER SERVICE:
Should the product require service, please call the following number for your
nearest Authorized Alpine Service Center.
CAR AUDIO NAVIGATION
1-800-ALPINE-1 (1-800-257-4631) 1-888 -NAV-HELP (1-888-628-4357)
Or visit our website at; http://www.alpine-usa.com
ALPINE ELECTRONICS OF AMERICA, INC., 1500 Atlantic Blvd, Auburn Hills, Michigan 48326, U.S.A. Do not send products to this address. Call the toll free telephone number or visit the website to locate a service center.
1-7, Yukigaya-Otsukamachi, Ota-ku, Tokyo 145-0067, JAPAN Phone: 03-5499-4531
1500 Atlantic Blvd, Auburn Hills, Michigan 48326, U.S.A. Phone 1-800-ALPINE-1
(1-800-257-4631)
161-165 Princes Highway, Hallam Victoria 3803, Australia
Phone 03-8787-1200
Ohmstraße 4 85716 Unterschleißheim, Germany
Phone: 089-32 42 640
Alpine House Fletchamstead Highway, Coventry CV4 9TW, U.K. www.alpine.co.uk
184 allée des Erables CS 52016 Villepinte 95 945 Roissy CDG cedex
FRANCE Phone : + 33(0)1 48 63 89 89
Viale Cristoforo Colombo, 8 20090 Trezzano sul Naviglio MI, Italy
Phone +39 02 484781
Portal de Gamarra 36, Pabellón, 32 01013 Vitoria (Alava)-APDO 133, Spain
Phone 945-283588
Take a moment to protect your purchase by registering your product now at www
.alpine-usa. com/registration. You will also be updated on product
information, special promotions, Alpine news.
Prenez le temps de protéger votre achat en enregistrant votre produit sur www
.alpine-usa.com/ registration. Vous recevrez en outre des mises à jours sur
des informations de produits, des offres promotionnelles et des nouvelles
concernant Alpine.
Le recomendamos que proteja su adquisición registrando su producto lo antes
posible en la dirección www.alpine-usa.com/registration. Asimismo, recibirá
información sobre productos, promociones especiales y noticias de Alpine.
Designed by ALPINE Japan Printed in China
7-INCH AUDIO/VIDEO RECEIVER
EN
iLX-W670 FR
ES
· OWNER’S MANUAL Please read before using this equipment.
· MODE D’EMPLOI Veuillez lire avant d’utiliser cet appareil.
· MANUAL DE OPERACIÓN Léalo antes de utilizar este equipo.
Thank you for purchasing this Alpine product. Please take a moment to protect
your purchase by registering your product now at the following address: www
.alpine-usa.com/registration. You will be informed of product and software
updates (if applicable), special promotions, news about Alpine.
Merci d’avoir acheté ce produit Alpine. Nous vous invitons à consacrer un
moment à la protection de votre achat en enregistrant votre produit dès
maintenant à l’adresse suivante : www.alpine-usa.com/registration. Vous serez
tenu informé des mises à jour des produits et des logiciels (le cas échéant),
des promotions spéciales et de l’actualité d’Alpine.
Gracias por adquirir este producto Alpine. Con solo unos pocos pasos podrá
proteger su producto, registrándolo a través de la siguiente dirección: www
.alpine-usa.com/registration. Recibirá información sobre nuevos productos y
software, promociones especiales y novedades sobre Alpine.
ALPS ALPINE NORTH AMERICA, INC. 1500 Atlantic Blvd,
Auburn Hills, Michigan 48326, U.S.A. Phone 1-800-ALPINE-1
(1-800-257-4631)
Designed by ALPINE Japan
Contents
Operating Instructions
PRECAUTIONS
IMPORTANT INFORMATION………………………..5
WARNING
Points to Observe for Safe Usage………………………..5 WARNING ………………………………………………… 5
CAUTION …………………………………………………. 6 NOTICE ……………………………………………………. 7
Getting Started
Location of Controls ………………………………………….9 Turning Power On or
Off…………………………………..9 Turning the System On ……………………………………..9 Adjusting the
Volume………………………………………..9 Lowering Volume Quickly …………………………………9 Touch Screen
Operation…………………………………..10 About the HOME Screen …………………………………10 About the
Indicator Display …………………………….11
Radio
Radio Basic Operation Listening to the Radio ……………………………………..12 Presetting
Stations Manually ……………………………12 Presetting Stations Automatically …………………….12
Mode switching Settings ………………………………….12
Apple CarPlay (Optional)
Access to Apple CarPlay…………………………………..13
Android AutoTM (Optional)
What is Android Auto ……………………………………..13 Activate Android Auto
…………………………………….13
USB Flash drive (Optional)
Playback…………………………………………………………..15 Fast-forwarding/Fast-reversing
(USB Audio/Video)………………………………………15 Repeat Play (USB Audio/Video) ………………………15
Shuffle Play (USB Audio/Video) ………………………15 Searching for a Desired
Song/Video/Photo………15 Slide Show (USB Photo)…………………………………..15 About USB List
………………………………………………..15
iPod mode on iPhone (Optional)
Playback…………………………………………………………..16 Searching for a Music File………………………………..17
Repeat Play………………………………………………………17 Shuffle Play………………………………………………………17
SiriusXM® Satellite Radio Operation (Optional)
Receiving Channels with the SiriusXM Tuner ….18 Tuning Channels by Category
………………………….18 Checking the Sirius XM Radio ID Number ……..19 Storing Channel
Presets …………………………………..19 Tuning Channels Using Presets………………………..19 SiriusXM
List …………………………………………………..19 Selecting The Channel Directly………………………..19
Parental Lock Function ……………………………………19
Bluetooth® Operation
Setup Before Using…………………………………………..20 About Bluetooth …………………………………………..20
About the Hands-free Phone ………………………..20 Before Using Bluetooth…………………………………20
Hands-free Phone Control
Answering a Call ……………………………………………..21 Hanging up the Telephone……………………………….21
Calling……………………………………………………………..21
Making a phone call using the Phone Menu …21 Siri
…………………………………………………………………..22 Phone Operation Screen ………………………………….23
Adjusting the Speech Volume……………………….23 Changing the Voice Output
………………………….23 DTMF (Touch-Tone) Function …………………….23
2-EN
Phone Book Function………………………………………23 Synchronizing the Phone Book …………………….23
Bluetooth® Audio Playback…………………………………………………………..24 Repeat
Play………………………………………………………24 Shuffle Play………………………………………………………24
AUX Operation (Optional)
AUX Operation ……………………………………………….24
Camera Operation (Optional)
Camera Operation …………………………………………..25 Displaying the Camera Image from the
Menu screen ……………………………….25 Displaying the rear view video while the car is in
reverse…………………………..25
About the Rear Camera Guide …………………………25
Sound Boost and Lighting link (Optional)
Lighting Link Setting Operation ………………………26 Lighting Link settings
Colors………………………..27
Setup
Setup Operation ………………………………………………28
System Setup Language Setup………………………………………………..29 Time Adjust
Setup……………………………………………29 SiriusXM Setup …………………………………………….29 Parental Control
………………………………………………29 Clear Locked All………………………………………………30 Changing the Lock
Passcode ……………………………30 Version …………………………………………………………….30 Product
Information………………………………………..30 Updating the firmware version……………………..30
Software License………………………………………………31 Connection Status ……………………………………………31
Steering Wheel Control……………………………………31 Reset ……………………………………………………………….. 31
Screen/Lighting Setup Dimmer …………………………………………………………..32 Screen
Color…………………………………………………….32 Key Color ………………………………………………………..32
Sound Setup
Setting the Fader/Balance……………………………..33 Adjusting the
Bass/Middle/Treble…………………33 Adjusting the Graphic Equalizer
Curve (EQ) ……………………………………………….33 Setting an Equalizer ……………………………………..34
Setting the Subwoofer …………………………………..35 Adjusting the Crossover Settings
(X-Over) …..35 Adjusting the Time Correction (TCR) ………….35 Setting the Speaker
Level………………………………36 Setting Defeat……………………………………………….36 About the Crossover
………………………………………..36 About Time Correction……………………………………37 Example 1. Listening
Position:
Front Left Seat …………………………………………..37 Example 2. Listening Position: All Seats
……….37
Volume Setup
Volume Setup…………………………………………………..38
Bluetooth Setup
Device List……………………………………………………….38 Pairing the Bluetooth Device ………………………..38
Fast pairing the Bluetooth Device …………………38 Deleting a Bluetooth Device from
the list……..38 Searching for a Bluetooth Device ………………….38 Displaying
Bluetooth Information ………………..39 Auto Connection ………………………………………….39
Downloading the Phonebook……………………….39
Rear Camera Setup
Parking Guide Adjust Setup……………………………..39 Video Setup……………………………………………………..40
Lighting Link ON/OFF
Information
About the Supported Formats ………………………….42 About Audio Format…………………………………….42
About Video Format …………………………………….42 About Photo Format …………………………………….43
In Case of Difficulty …………………………………………44 If this Message Appears
……………………………………45 Specifications …………………………………………………..47
3-EN
Installation and Connections
WARNING ………………………………………………. 48 CAUTION ……………………………………………….. 48
Precautions……………………………………………. 48 Accessory List ………………………………………………….49
Installation ………………………………………………………49
Caution concerning the installation location……………………………………………………..49
Mounting the Microphone……………………………49 Installation example using the Original
Mounting Bracket ……………………………………..49 Connections ……………………………………………………. 50
If an ACC power supply is not available………..52 System
Example……………………………………………….53
OEM Steering Wheel Control Rentention …….54
LIMITED WARRANTY
4-EN
Operating Instructions
PRECAUTIONS
IMPORTANT INFORMATION
FCC COMPLIANCE STATEMENT This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide more reasonable protection against
harmful interference in a residential installation, and are more stringent
than “outdoor” requirements.
Operation is subjected to the following two conditions: (1) This device may
not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired
operation.
This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, you are encouraged to try to
correct the interference by one of the following measures: · Reorient or
relocate the receiving antenna. · Increase the separation between the
equipment and the receiver. · Connect the equipment into an outlet on a
circuit different from
that to which the receiver is connected. · Consult an experienced radio/TV
technician.
WARNING
Points to Observe for Safe Usage
· Read this manual carefully before using this system components. They contain
instructions on how to use this product in a safe and effective manner. Alpine
cannot be responsible for problems resulting from failure to observe the
instructions in this manual.
· This manual uses various pictorial displays to show you how to use this
product safely and to alert you to potential dangers resulting from improper
connections and operation. Following are the meanings of these pictorial
displays. It is important to fully understand the meanings of these pictorial
displays in order to use this manual and the system properly.
· This product may be used with software applications. Please follow all usage
instructions and warnings when using this product at all times. Do not use
this product or any software application in a manner which will hinder safe
operation of your vehicle.
WARNING
· Operation of the system while driving is dangerous. Users should stop
vehicle before operating the software.
· Road conditions and regulations take precedence over information contained
on the map display: observe actual traffic restrictions and circumstances
while driving.
· This software is designed for use exclusively in the unit. It cannot and may
not be used in conjunction with other hardware.
WARNING
This symbol means important instructions. Failure to heed them can result in
serious injury or death.
INSTALL THE PRODUCT CORRECTLY SO THAT THE DRIVER CANNOT WATCH TV/VIDEO UNLESS
THE VEHICLE IS STOPPED AND THE PARKING BRAKE IS APPLIED. It is dangerous for
the driver to watch TV/Video while driving a vehicle. Installing this product
incorrectly enables the driver to watch TV/Video while driving. This may cause
a distraction, preventing the driver from looking ahead, thus causing an
accident. The driver or other people could be severely injured.
DO NOT WATCH VIDEO WHILE DRIVING. Watching the video may distract the driver
from looking ahead of the vehicle and cause an accident
DO NOT OPERATE ANY FUNCTION THAT TAKES YOUR ATTENTION AWAY FROM SAFELY DRIVING
YOUR VEHICLE. Any function that requires your prolonged attention should only
be performed after coming to a complete stop. Always stop the vehicle in a
safe location before performing these functions. Failure to do so may result
in an accident.
KEEP THE VOLUME AT A LEVEL WHERE YOU CAN STILL HEAR OUTSIDE NOISES WHILE
DRIVING. Excessive volume levels that obscure sounds such as emergency vehicle
sirens or road warning signals (train crossings, etc.) can be dangerous and
may result in an accident. LISTENING AT LOUD VOLUME LEVELS IN A CAR MAY ALSO
CAUSE HEARING DAMAGE.
MINIMIZE DISPLAY VIEWING WHILE DRIVING. Viewing the display may distract the
driver from looking ahead of the vehicle and cause an accident.
DO NOT DISASSEMBLE OR ALTER. Doing so may result in an accident, fire or
electric shock.
USE ONLY IN CARS WITH A 12 VOLT NEGATIVE GROUND. (Check with your dealer if
you are not sure.) Failure to do so may result in fire, etc.
5-EN
KEEP SMALL OBJECTS SUCH AS SCREWS OUT OF THE REACH OF CHILDREN. Swallowing
them may result in serious injury. If swallowed, consult a physician
immediately.
USE THE CORRECT AMPERE RATING WHEN REPLACING FUSES. Failure to do so may
result in fire or electric shock.
DO NOT BLOCK VENTS OR RADIATOR PANELS. Doing so may cause heat to build up
inside and may result in fire.
USE THIS PRODUCT FOR MOBILE 12V APPLICATIONS. Use for other than its designed
application may result in fire, electric shock or other injury.
MAKE THE CORRECT CONNECTIONS. Failure to make the proper connections may
result in fire or product damage.
BEFORE WIRING, DISCONNECT THE CABLE FROM THE NEGATIVE BATTERY TERMINAL.
Failure to do so may result in electric shock or injury due to electrical
shorts.
DO NOT ALLOW CABLES TO BECOME ENTANGLED IN SURROUNDING OBJECTS. Arrange wiring
and cables in compliance with the manual to prevent obstructions when driving.
Cables or wiring that obstruct or hang up on places such as the steering
wheel, gear lever, brake pedals, etc. can be extremely hazardous.
DO NOT SPLICE INTO ELECTRICAL CABLES. Never cut away cable insulation to
supply power to other equipment. Doing so will exceed the current carrying
capacity of the wire and result in fire or electric shock.
DO NOT DAMAGE PIPE OR WIRING WHEN DRILLING HOLES. When drilling holes in the
chassis for installation, take precautions so as not to contact, damage or
obstruct pipes, fuel lines, tanks or electrical wiring. Failure to take such
precautions may result in fire.
DO NOT USE BOLTS OR NUTS IN THE BRAKE OR STEERING SYSTEMS TO MAKE GROUND
CONNECTIONS. Bolts or nuts used for the brake or steering systems (or any
other safety-related system), or tanks should NEVER be used for installations
or ground connections. Using such parts could disable control of the vehicle
and cause fire etc.
DO NOT INSTALL IN LOCATIONS WHICH MIGHT HINDER VEHICLE OPERATION, SUCH AS THE
STEERING WHEEL OR GEARSHIFT. Doing so may obstruct forward vision or hamper
movement etc. and results in serious accident.
CAUTION
This symbol means important instructions. Failure to heed them can result in
injury or material property damage.
HALT USE IMMEDIATELY IF A PROBLEM APPEARS. Failure to do so may cause personal
injury or damage to the product. Return it to your authorized Alpine dealer or
the nearest Alpine Service Center for repairing.
HAVE THE WIRING AND INSTALLATION DONE BY EXPERTS. The wiring and installation
of this unit requires special technical skill and experience. To ensure
safety, always contact the dealer where you purchased this product to have the
work done.
USE SPECIFIED ACCESSORY PARTS AND INSTALL THEM SECURELY. Be sure to use only
the specified accessory parts. Use of other than designated parts may damage
this unit internally or may not securely install the unit in place. This may
cause parts to become loose resulting in hazards or product failure.
ARRANGE THE WIRING SO IT IS NOT CRIMPED OR PINCHED BY A SHARP METAL EDGE.
Route the cables and wiring away from moving parts (like the seat rails) or
sharp or pointed edges. This will prevent crimping and damage to the wiring.
If wiring passes through a hole in metal, use a rubber grommet to prevent the
wire’s insulation from being cut by the metal edge of the hole.
DO NOT INSTALL IN LOCATIONS WITH HIGH MOISTURE OR DUST. Avoid installing the
unit in locations with high incidence of moisture or dust. Moisture or dust
that penetrates into this unit may result in product failure.
6-EN
NOTICE
Product Cleaning Use a soft dry cloth for periodic cleaning of the product.
For more severe stains, please dampen the cloth with water only. Anything else
has the chance of dissolving the paint or damaging the plastic.
Temperature Be sure the temperature inside the vehicle is between +45°C
(+113°F) and 0°C (+32°F) before turning your unit on.
Maintenance If you have problems, do not attempt to repair the unit yourself.
Return it to your Alpine dealer or the nearest Alpine Service Station for
servicing.
Protecting the USB connector · Only an Phone or USB flash drive can be
connected to the USB
connector on this unit. Correct performance using other USB products cannot be
guaranteed. · If the USB connector is used, be sure to use only the supplied
connector cable with the unit. A USB hub is not supported. · Depending on the
connected USB flash drive, the unit may not function or some functions may not
be performed. · The audio file format that can be played on the unit is MP3/
WMA/WAVE/AAC/FLAC/Ogg/APE. · Artist/song name, etc., can be displayed.
Certain, special characters may not be correctly displayed.
CAUTION
Alpine accepts no responsibility for lost data, etc., even if data, etc., is
lost while using this product.
On Handling USB Flash drive · This unit can control a memory storage device
that supports
the USB Mass Storage Class (MSC) protocol. Playable audio file formats are
MP3, WMA, AAC,WAVE,APE,OGG and FLAC. · USB Flash drive function is not
guaranteed. Use a USB flash drive according to the terms of agreement. Read
the USB flash drive Owner’s Manual thoroughly. · Avoid usage or storage in the
following locations:
Anywhere in the car exposed to direct sunlight or high temperatures. Anywhere
the possibility of high humidity or corrosive substances are present. · Fix
the USB flash drive in a location where driver operation will not be hindered.
· USB Flash drive may not function correctly at high or low temperature. · Use
only certified USB flash drive. Note that even certified USB flash drive, may
not function correctly depending on its type or state. · Depending on the
settings of the USB flash drive type, memory state or encoding software, the
unit may not play back or display properly. · USB Flash drive may take time to
start playback. If there is a particular file other than audio in the USB
flash drive, it may take considerable time before the file is played back or
searched. · The unit can play back”mp2″, “mpa””mp3″”m4a”, “wma”, “m4a”,
“flac”/”fla”,”wav””ogg””ape”file extensions. · Do not add the above extensions
to a file other than audio data. This non-audio data will not be recognized.
The resulting playback may contain noise that can damage speakers and/or
amplifiers. · It is recommended to back up important data on a personal
computer. · Do not remove the USB device while playback is in progress. Change
SOURCE to something other than USB, then remove the USB device to prevent
possible damage to its memory.
7-EN
· Windows Media and the Windows logo are trademarks, or registered trademarks
of Microsoft Corporation in the United States and/or other countries.
· Apple, iPhone, iPod, iPod nano, iPod touch, iPad, Lightning and Siri are
trademarks of Apple Inc., registered in the U.S. and other countries. Apple
CarPlay is a trademark of Apple Inc.
· Use of the Made for Apple and Works with Apple badges means that an
accessory has been designed to connect specifically to the Apple product(s)
identified in the Made for Apple badge and to work specifically with the
technology identified in the Works with Apple badge, and has been certified by
the developer to meet Apple performance standards. Apple is not responsible
for the operation of this device or its compliance with safety and regulatory
standards.
· Please note that the use of this accessory with an Apple product may affect
wireless performance.
· Use of the Apple CarPlay logo means that a vehicle user interface meets
Apple performance standards. Apple is not responsible for the operation of
this vehicle or its compliance with safety and regulatory standards. Please
note that the use of this product with iPhone may affect wireless performance.
· SiriusXM and all related marks and logos are trademarks of Sirius XM Radio
Inc. All rights reserved.
· Google, Android, Google Play and Android Auto are trademarks of Google
LLC.To use Android Auto on your car display, you’ll need an Android Auto
compatible vehicle or aftermarket stereo, an Android phone running Android 6.0
or higher, and the Android Auto app.
· The Bluetooth® word mark and logos are registered trademarks owned by the
Bluetooth SIG, Inc. and any use of such marks by Alpine Electronics, Inc. is
under license.
· MPEG Layer-3 audio coding technology licensed from Fraunhofer IIS and
Thomson. Supply of this product only conveys a license for private, non-
commercial use and does not convey a license nor imply any right to use this
product in any commercial (i.e. revenue-generation) real time broadcasting
(terrestrial, satellite, cable and/or any other media), broadcasting/streaming
via internet, intranets and/or other networks or in other electronic content
distribution systems, such as pay-audio or audio-on-demand applications. An
independent license for such use is required. For details, please visit
http://www.mp3licensing.com
8-EN
Getting Started
Location of Controls
When system is powered off ,Short/long touch any button to turn the power on.
Turning Power On or Off
Some of this unit’s functions cannot be performed while the vehicle is in
motion. Be sure to stop your vehicle in a safe location and apply the parking
brake, before attempting these operations.
1 Turn the ignition key to the ACC or ON position.
The system turns on. · When turned on, the system displays the last screen
that was
displayed before the ignition key was turned off. For example, if the unit is
in radio mode when ignition is turned off, it will remain in radio mode when
ignition is turned back on.
2 Touch and hold the (HOME)/(Power Off) button for
at least 1.7 second to turn the power off.
· When the system is used for the first time, the language selection menu is
displayed. Select the desired language, and then touch [OK].
· The unit can be turned on by touching the [ ] (HOME) button, [ ] button [ ]
button [ ] button or [ ] (Phone) button.
· The unit is a precision device. Careful handling of the unit should provide
you with years of trouble-free operation.
A / (DOWN/UP) button Touch to adjust the volume. Touch and hold this button for at least 1.7 second to adjust the volume to maximum or minimum
B (MUTE) button · Touch to activate/deactivate the mute mode. · Touch and hold this button for at least 1.7 second to display on/off
C
(HOME)/(Power Off) button
Activates the HOME screen.
Touch and hold this button for at least 1.7 second to turn the
power off.
D (Phone) button Activates the Phone screen.
E button · When phone is connected to CarPlay, touch this button to activate Siri · When phone is connected to Android Auto ,touch this button to activate VR · When Siri is activated, the function of Siri is available · When VR is activated, the VR setting is ON and the function of VR is available · When the CarPlay/Android Audio is disconnected ,the operation in this button is invalidate · When CarPlay/Android Audio is disconnected, touch and long hold to enter into the Device Searching List to activate the new device searching
E (Reset) button Reset& Restart.
About the button descriptions used in this Owner’s Manual The buttons found on the face of the unit are expressed in bold (e.g. (HOME)). The buttons found on the touch-screen display are shown in bold within brackets, [ ] (e.g. [ ]).
Turning the System On
When the system is used for the first time, the language selection menu is
displayed. Select a language, and then touch [OK].
· Some of this unit’s functions cannot be performed while the vehicle is in
motion. Be sure to stop your vehicle in a safe location and apply the parking
brake before attempting these operations.
Adjusting the Volume
Adjust the volume by touching / Volume decreases increases continuously by
touching and holding
/ Volume: 0 – 35
Lowering Volume Quickly
Audio Mute function instantly lowers the volume level to 0.
1 Touch the (MUTE) button to activate the MUTE mode.
The audio level will be 0.
2 Touching the (MUTE) button again will bring the
audio back to its previous level.
9-EN
Touch Screen Operation
You can operate the system by using the touch panel on the screen. · Be sure
to touch the onscreen button lightly with the pad of your finger
to avoid scratching the display. Touch a button or list item on the screen
lightly.
About the HOME Screen
In the HOME screen, you can select the audio source and perform various setups
or operations on the unit. Touch the (HOME) button. The HOME screen is
displayed.
HOME screen example (Page1)
Radio Apple CarPlay Android Auto USB
iPod
SiriusXM
Bluetooth Audio Phone AUX Camera
Displays the Radio main screen (page 12).
You can use Apple CarPlay (page 13).
You can use Android Auto (page 13).
You can play back music files, video files and photo files stored in a USB
flash drive (page 14). · If a USB flash drive is not connected, this
widget is not available.
Displays the iPod main screen (page 16) · If an iPhone is not connected, this
widget is
not available.
Displays the SiriusXM main screen (page 18). · If a SiriusXM Tuner (Optional)
is not
connected, this widget is not available.
Displays the Bluetooth Audio main screen (page 23).
Displays the Phone main screen (page 23).
Displays the AUX main screen (page 24).
Displays the Camera main screen (page 25).
HOME screen example (Page2)
10-EN
About the Indicator Display
The Indicator Bar at the top of the screen displays various types of
information, like the current time.
A Sound Boost. You can turn theSound Boost (page 26).
B Lights up when connected to a Bluetooth compatible device. · Sets ash when
Bluetooth disconnected
C Indicates the battery level of the connected Bluetooth device.
Battery Level
Level 3
Level 2
Level 1 No Battery
Icon
This may not be displayed depending on the connected Bluetooth device. D Indicates the signal strength level of the connected Bluetooth compatible device. Displayed when Bluetooth setting is ON.
0
1
2
3
4
5
E Indicates the current time. You can switch between the 12 hour display and
24 hour display options (page 29).
F Setup Click to enter the Settings
G Display SiriusXM signal level
0
1
2
3
H Indicates the volume on/off status.
11-EN
Radio
Radio Basic Operation
Radio main screen example
Listening to the Radio
1 Touch the (HOME) button and select radio mode.
The display shows the radio mode screen.
2 Select the desired band from [FM1] / [FM2] / [FM3] /
[AM1]/[AM2].
3 Touch [ ], [
frequency.
] [ ], [ ] to adjust the radio
Presetting Stations Manually
A Band button Switches a band.
B Preset button Displays the preset stations with a short touch. Touch for at
least 1.5. second to memorise the current station as a preset station.
C Plays each preset station for about 10 seconds. D Scan and memorises active
stations automatically E Touch [ ] [ ] to select the station seek up or seek
down respectively Touch [ ] [ ] to change the radio frequency up or down
respectively. Operate in manual mode F Switch Local mode/Manual mode/DX mode
Seek up [ ] Seek up: From the current station ,seek forward according to the
specified step unit , After selecting a active station, then play If no active
station, will keep searching
Seek down [ ] Seek down: From the current station ,seek down according to the
specified step unit , After selecting a active station, then play If no active
station, will keep searching
1 Tune in a desired radio station you wish to store in the
preset memory by manual or automatic seek tuning.
2 Touch and hold the Preset number you want to store for
at least 1.5 second. The selected station is stored.
3 Repeat the procedure to store up to 5 other stations
onto the same band. To use this procedure for other bands, simply select the
desired band and repeat the procedure.
A total of 30 stations can be stored in the preset memory (6 stations for each
band; FM1, FM2, FM3, orAM1,AM2).
· If a preset memory has already been set in the same preset number, it will
be cleared and the new station will be memorized.
Presetting Stations Automatically
From the start Frequency ,scan upon the step unit (+1) and store the validated
station ,After one cycle, store the station from low frequency to high
frequency
Touch [ A.MEMO] go to Scan for stations and store valid stations
· If a valid station is scanned, it is not required to play, the screen
display “scanning” during the scanning process and will automatically switch
to the first stored station on FM1
12-EN
Mode switching Settings
Setting item: Manual/DX(Initial setting)/Local
Setting contents: Manual mode:manually scanning station
DX mode: When select the DX mode and start to search ,it will be performed
until the next or previous valid station, if no valid station is searched, the
search continues
Local mode: When select the local mode and start to search ,it will be
performed until the next or previous valid station, if no valid station is
searched, the search continues
· :By default, Dx mode is used. The Local mode stop sensitivity is increased
by 30db over Dx under AM and FM
Apple CarPlay (Optional)
Android AutoTM (Optional)
Apple CarPlay is a smarter, safer way to use your iPhone in the car. Apple
CarPlay takes the things you want to do with your iPhone while driving and
puts them right on the unit. You can get directions, make calls, send and
receive messages, and listen to music, all in a way that allows you to stay
focused on the road. Just plug in your iPhone to the unit and go.
· Before using this function, plug in your iPhone using Lightning to USB Cable
(Supplied with iPhone) to the unit.
· Some functions may not be available while driving. · About iPhone models
usable with this unit, see “iPod mode on iPhone
(Optional)” (page 16). Only an iPhone 6 or later compatible with Apple CarPlay
function.
Access to Apple CarPlay
1 Touch the (HOME) button.
The HOME screen is displayed.
2 Touch [Apple CarPlay].
The Apple CarPlay screen is displayed. Touch the desired App icon on the unit,
or use Siri function by touching the button.
· When a used iPhone 6 or later is reconnected, touch the pop-up
message-“Apple CarPlay connected.” within 5 seconds to access to Apple CarPlay
screen.
· The App must be Apple CarPlay compatible in order to appear in the Home
screen.
What is Android Auto
Android Auto is designed to make it easier to use apps from your phone while
you’re on the road. Navigate with Google Maps, listen to Playlists or Podcasts
from your favorite apps, and more.
Activate Android Auto
Download the Android Auto App from the Google Play Store before continuing.
Just plug in your smartphone to the unit’s USB connector, then follow the
prompt to pair your smartphone with the unit.
· The connected smartphone with Android Auto will disconnect other phone’s
Bluetooth connection and pair to the unit.
1 Touch the (HOME) button.
The HOME screen is displayed.
2 Touch [Android Auto].
The Android Auto screen is displayed.
· You can make a call, use voice recognition function and Android Auto’s
compatible navigation app, etc,.
· Only Google approved apps with necessary driver-safety measures in place can
be used.
13-EN
USB Flash drive (Optional)
USB Photo mode screen
You can play back music files (WAVE.WMA.AAC.MP3.OGG.FLAC. APE), video files (AVI,MPEG 1/2,MPEG4,WMV,Flash,QuickTime,ASF, Matroska Video,TS Stream,3GP) and photo files (JPG,JPEG,PNG,BMP) stored in a USB flash drive on the internal player of this system.
WARNING It is dangerous for the driver to watch video while driving the
vehicle. The driver may be distracted from looking ahead and an accident could
occur.
Install the unit correctly so that the driver cannot watch a video unless the
car is stopped and the parking brake is applied.
If the unit is not installed correctly, the driver will be able to watch a
video while driving and may be distracted from looking ahead and cause an
accident. The driver or other people could be severely injured.
USB Audio mode screen
A Artwork display B Information display C Elapsed time/Total time for playing
D Displays the USB List screen E Shuffle mode F [ ] repeat_off, [ ]
repeat_folder, [ ] repeat_one,
[ ] repeat_all, G Finds the beginning of next chapter//Fast-forwards when
touched for at least 2 second H Pause and Play I Finds the beginning of the
current file/Finds a previous file
within 1 second after playback starts/Fast-reverses when touched for at least
2 second J Video information display K Video Setup display L Photo information
display M Rotate mode
· For your safety, video is not displayed and only audio can be heard while
driving.
USB Video mode screen
14-EN
Playback
1 Touch the (HOME) button and select USB mode.
The display shows the USB mode screen.
2 Touch [ ] (Search). 3 Select the desired mode.
: USB Audio mode : USB Video mode : USB Photo mode
4 Touch [ ] or [ ] to select the desired track(file).
Returning to the beginning of the previous track (file): Touch [ ].
Fast reverse the current track : Touch and hold 2s [ ].
Advancing to the beginning of the next track (file) : Touch [ ].
Fast forward the current track : Touch and hold 2s [ ].
3 To pause playback, touch [ ] .
Touching [ ] again will resume playback.
· The playback time may not be correctly displayed when a VBR (Variable Bit
Rate) recorded file is played back.
· If there is tag information, artist name/album name/track name is displayed.
· If there is no label information, no name is displayed. · ID3 tag/WMA tag
If an MP3/WMA/AAC/FLAC/WAVE/Ogg/APE file contains ID3 tag/ WMA tag
information, the ID3 tag/WMA tag information is displayed. (e.g., song name,
artist name, and album name)
Fast-forwarding/Fast-reversing (USB Audio/ Video)
During playback, touch and hold [ ] (Fast-reverse) or touch and hold [ ]
(Fast-forward). Touch and hold for more than 2 second to fast-forward/fast-
reverse.
· Fast-reverse Speed: touch [ ] to change the speed, x4 x10 x32 off
· Fast-forward Speed: touch [ ] to change the speed, x4 x10 x32 off
Repeat Play (USB Audio/Video)
1 Touch [ ].
· The [ ] button displays the currently selected mode.
2 Select your desired Repeat mode.
ALL : All files are repeatedly played back. One : Only the file currently
playing is repeatedly played back. Folder : Only files in a folder are
repeatedly played back. OFF : Repeat mode is Off.
Shuffle Play (USB Audio/Video)
1 Touch [
· The [
]. ] button displays the currently selected mode.
2 Shuffle mode is only valid in [ ] [ ] [ ].
3 When in [ ] touch [ ], automatically switch [ ].
Searching for a Desired Song/Video/Photo
1 Touch [ ] (Search). 2 Select the desired mode.
: USB Audio mode : USB Video mode : USB Photo mode
3 Touch [ ] or [ ] to select the folder. 4 Touch your desired File name.
When you select a Folder name, repeat the same procedure to select another
Folder name or File name.
Slide Show (USB Photo)
The Slide Show shows photos that change every 5 seconds. To pause playback,
touch [ ] Touching [ ] again will resume playback.
About USB List
You can select the desired mode · Each page displays up to 5 files . if you
want to view more than 5 files,
swipe down or touch alphabet to search
About order Display and sort according to the head character Display in the
order of 1 -> 2 -> 3 below. 0: Folder :When there are folders ,the folders are
displayed ahead of
the files 1: Number ( represented by “#” on the Right Search Bar ) 2: English
Alphabet 3: Shorting order of Unicode
Right Search Bar (order of list ) 1: Number ( represented by “#” on the Right
Search Bar ) 2: English Alphabet · Search only the files with numeric or
English alphabetic headers
15-EN
iPod mode on iPhone
(Optional)
Before using this function, plug in your iPhone using a Lightning-USB cable
(supplied with iPhone) to the unit,
· This unit does not support video playback from iPhone which connected to
this unit via USB Connector.
· Internet or telephone function, etc., of the iPhone is not controllable from
the unit, but these functions can be controlled using the iPhone itself.
About iPhone models usable with this unit · The following devices have been
tested and shown to work
with this unit. Correct function of earlier versions cannot be guaranteed.
iPhone 14 Pro Max, iPhone 14 Pro, iPhone 14 Plus, iPhone 14, iPhone SE (3rd
generation), iPhone 13 Pro Max, iPhone 13 Pro, iPhone 13, iPhone 13 mini,
iPhone 12 Pro Max, iPhone 12 Pro, iPhone 12, iPhone 12 mini, iPhone SE (2nd
generation), iPhone 11 Pro Max, iPhone 11 Pro, iPhone 11, iPhone XS Max,
iPhone XS, iPhone XR, iPhone X, iPhone 8 Plus, iPhone 8, iPhone 7 Plus, iPhone
7, iPhone SE, iPhone 6s Plus, iPhone 6s, iPhone 6 Plus, iPhone 6
iPod main screen example
Playback
1 Touch the (HOME) button and select iPod mode.
The display shows the iPod mode screen.
2 Touch [ ] or [ ] or to select the desired track (file).
Returning to the beginning of the previous track (file): Touch [ ].
Fast reverse the current track : Touch and hold 2s [ ].
Advancing to the beginning of the next track (file) : Touch [ ].
Fast forward the current track : Touch and hold 2s [ ].
3 To pause playback, touch [ ].
Touching [ ] again will resume playback.
· If a song is playing on the iPhone before it is connected to the unit, it
will continue playing when it is connected.
· An episode may have several chapters. The chapter can be changed by touching
[ ] or [ ].
· If the artist, album or song name, created in iTunes, has too many
characters, songs may not be played back when connected to the unit.
Therefore, a maximum of 255 characters is recommended. The maximum number of
characters for the unit is 255.
· Some characters may not be correctly displayed.
A Artwork display B Information display* C Elapsed time/Total time for playing
Repeat mode D Displays the iPod List screen E Shuffle mode F [ ]repeat_off, [
]repeat_one, [ ]repeat_all, G Finds the beginning of next chapter/Fast-
forwards
When touched for at least 2 second H Pause and Play I Finds the beginning of
the current file/Finds a previous
filewithin 1 second after playback starts/Fast-reverses when touched for at
least 2 second
- Podcast mode.
16-EN
Searching for a Music File
Hierarchy 1 Radio Playlists Artists Albums Songs Genres Composers Podcasts Audiobook
Hierarchy 2 — Songs Albums Songs — Artists Albums Episodes —
Hierarchy 3 — — Songs — — Albums Songs — —
Hierarchy 4 — — — — — Songs — — —
For example: Searching by Artist name The following example explains how an Artists search is performed.
Shuffle Play
1 Touch [
· The [
]. ] button displays the currently selected mode.
2 Shuffle mode is only valid in[ ][ ][ ].
3 When in [ ] touch [ ] ,automatically switch[ ].
1 Touch [ ] (Search) during playback. 2 Touch [Artists].
The Artists search screen is displayed.
3 Select the desired artist. 4 Touch the desired album’s name.
All songs of the selected album are displayed
5 Touch the desired song’s name.
The selected song is played back. · If you touch [ ], the category browsing
mode screen is displayed.
Repeat Play
1 Touch [ ].
· The [ ] button displays the currently selected mode.
2 Select your desired Repeat mode.
ALL : All files are repeatedly played back. One : Only the file currently
playing is repeatedly played back. OFF : Repeat mode is Off.
17-EN
SiriusXM® Satellite Radio Operation (Optional)
SiriusXM Tuner operation: When an optional SiriusXM Tuner is connected to this
unit, the following operations may be performed. SiriusXM main screen example
A Band button Switches a band.
B Tune Select the specified channel manually
C Information display channel name, Artist Basic, Song Basic, Cat name
D Preset buttons Displays the preset channels with a short touch. Touch for at
least 1.5 second to memorize the current channel as a preset channel. Select
the channel number
E Displays the SiriusXM setup screen F Displays the SiriusXM List screen
All channel:Displays all channel Category:Select channel category Tune:Select
the specified channel manually G Changes to the next channel H Changes to the
previous channel
Receiving Channels with the SiriusXM Tuner
About SiriusXM Satellite Radio Only SiriusXM brings you more of what you love
to listen to, all in one place. Get over 140 channels, including commercial-
free music plus the best sports, news, talk, comedy and entertainment. Welcome
to the world of satellite radio. A SiriusXM Vehicle Tuner and Subscription are
required. For more information, visit www.siriusxm.com.
In the USA, you can activate online or by calling SiriusXM Listener Care: ·
Visit www.siriusxm.com/activatenow · Call SiriusXM Listener Care at
1-866-635-2349
For Canadian Subscriptions, please contact: · Visit www.siriusxm.ca/activate ·
Call SiriusXM Customer Care at
1-888-539-7474 · The SiriusXM Satellite
Radio controls on this unit are available only
when a SiriusXM Tuner is connected.
1 Touch the (HOME) button and select SiriusXM mode.
The display shows the SiriusXM mode screen.
2 Touch [ ] or [ ] to select the desired channel.
Touching and holding either button will rapidly browse through the channels.
· Refer to the SiriusXM Tuner User Guide for details on how to install the
SiriusXM Tuner.
Tuning Channels by Category
Channels are grouped into categories based on the type of content heard on the
channels.
1 Touch [ ] or [ ] to select the category browsing mode.
The channels within the category of the current channel are listed.
Category browsing mode screen example
2 Select the desired channel.
18-EN
Checking the Sirius XM Radio ID Number
To subscribe to the SiriusXM Satellite Radio service, it is necessary to
locate and identify the Radio ID of your SiriusXM Tuner. You can check the
Radio ID on the bottom surface of the SiriusXM Tuner box. You can also check
it from this unit by performing the following procedure.
1 While receiving SiriusXM Radio, touch [ ] or [ ] to
select channel “0”. The unit displays the Radio ID number.
2 To cancel the Radio ID number display, change the
channel to a channel other than “0”. · The SiriusXM Radio ID does not contain
the letters I, O, S, or F.
Storing Channel Presets
You can store 18 of your favorite SiriusXM channels for easy recall with
Preset buttons.
1 Long press the Preset number you can store the channel.
A maximum of 6 channels can be displayed on a page.
2 Repeat the procedure to store up to 17 other channels.
A total of 18 channels can be stored in the preset memory. · If you store a
new channel into a preset which already has a channel
assigned, the current channel will be cleared and replaced with the new one.
Tuning Channels Using Presets
Touch any one of the Preset numbers you have already stored in the Preset mode
screen. The preset channel is received.
SiriusXM List
1 Touch [ ] .
The list screen appears. List item:All Channels / Category Name/Tune The
Category name for the channel currently being received is displayed. · You can
switch the category by touching [ ] or [ ] on the List screen
after selecting a Search item.
List by ALL Channel
2 Touch [ ].
All Channels will be displayed in a list.
3 Touch the selected channel.
The channel you selected is received.
Searching by Category
2 Touch Category Name.
The channels within the category of the current channel are listed.
3 Touch the selected channel.
The channel you selected is received.
Selecting The Channel Directly
1 Touch [ ]or[ ].
The numeric keypad input screen is displayed.
2 Touch to input the channel number. 3 Touch [OK].
The selected channel is received.
Parental Lock Function
The Parental Control feature allows you to limit access to any SiriusXM
channels, including those with mature content. When enabled, the Parental
Control feature requires you to enter a passcode to tune to the locked
channels. For information on setting the Parental Control passcode, see
“Parental Control” (page 29). When a locked channel is selected, “Channel
[xxx] Locked” is displayed and then the numeric keypad appears for you to
enter the passcode.
Input the 4-digit passcode you set in “Parental Control” (page 29). The
initial number is 0000.
· If you input a wrong passcode, “Incorrect Pass Code entered” is displayed.
· After entering the correct passcode, you can access all locked channels
without entering the passcode again until the unit is powered off and then
back on.
19-EN
Bluetooth® Operation
Setup Before Using
About Bluetooth
Bluetooth is a wireless technology allowing communication between a mobile
device or personal computer over short distances. This enables a hands-free
call or data transmission between Bluetooth compatible devices. Bluetooth
transmission is available in the unlicensed 2.4 GHz spectrum if the distance
between devices is within 10 meters. For details, refer to the Bluetooth
website (http://www.bluetooth.com/).
· Depending on the Bluetooth version, a Bluetooth compatible device may not be
able to communicate with this unit.
· Proper function of this unit with all Bluetooth compatible devices is not
guaranteed. For handling of the Bluetooth compatible device, consult your
Alpine dealer or Alpine website.
· Depending on the surroundings, Bluetooth wireless connection may be
unstable.
· When you place a call, or perform setup operations, be sure to stop your car
in a safe place.
· Depending on the connected Bluetooth compatible device(s), the function may
differ. Also refer to the Owner’s Manual of the connected device(s).
About the Hands-free Phone
Hands-free calls are possible when using a HFP (Hands-Free Profile) compatible
mobile phone with this unit.
· Avoid performing a hands-free call in heavy traffic or on narrow or winding
streets.
· Close the windows while calling to reduce background noise.
· If both calling parties are using hands-free devices, or the call is made in
a noisy location, difficulty hearing the other person’s voice is normal.
· Depending on telephone line conditions or certain mobile devices used,
voices may sound unnatural.
· When using a microphone, speak as directly as you can into the microphone to
obtain the best sound quality.
· Certain mobile phone features are dependent on the capabilities and settings
of your service provider’s network. Additionally, certain features may not be
activated by your service provider, and/or the provider’s network settings may
limit the feature’s functionality. Always contact your service provider about
feature availability and functionality. All features, functionality, and other
product specifications, as well as the information contained in the Owner’s
Manual are based upon the latest available information and are believed to be
accurate at the time of printing. Alpine reserves the right to change or
modify any information or specifications without notice or obligation.
Before Using Bluetooth
Before using the hands-free phone/audio function, the following settings need
to be made.
Register a Bluetooth device in this unit. · See “Bluetooth Setup” (page 38). ·
You can search for this unit using a Bluetooth compatible device, and
then connect that Bluetooth compatible device to this unit. The device name of
this unit is “iLX-W670” and the initial number of the passcode is “0000.” Also
refer to the Owner’s Manual of the connected device(s).
Hands-free Phone Control
Touch [Bluetooth] in the HOME screen to display the Bluetooth menu screen.
Phone menu screen example
[Phone] button
Recent Events list You can display up to 100 items, such as phone numbers of
the most recent incoming calls, missed calls and outgoing calls, and contact
names that are registered in the Phone Book. When 100 items exist in the list,
the oldest item is deleted when a further item is to be added.
Contacts list You can make a phone call from the Phone Book, or edit the Phone
book.
Keypad screen Use to type a phone number.
20-EN
Answering a Call
1 An incoming call triggers the ringtone and an incoming
call display.
Phone Incoming screen example
Calling
Making a phone call using the Phone Menu
Entering a Phone Number to Make a Call
1 Touch [Keypad].
The number input screen (Keypad) appears.
2 Touch [ ] (Call).
The call starts.
A Touch[ ]Display Keypad screen B Touch switch Car speaker[ ]Or Phone speaker[
] C Touch switch mute on/ off D Adjust the volume level · During a call, the
audio for the current mode on the unit is muted.
After calling, playback will resume. · When the caller’s number is transmitted
to the system, if the caller’s
name is stored in the phone book, the name is displayed. If the name is not
stored, the number is displayed. · Touch [Decline] to reject an incoming call.
Hanging up the Telephone
1 Touch [ ] End Call.
The call finishes.
Touch [ ] to delete an entered number.
2 Enter the phone number you wish to call.
· You can enter up to 20 digits.
3 Touch [ ] (Call).
The phone call is started. · To change the Bluetooth device, see “Bluetooth
Setup” (page 38). Making a phone call from the Recent Events list
1 Touch [ ] to change to the Recent Events list screen.
2 Touch the name of the contact or number you want to
call. The phone call is started. Calling from the Contacts list (Phone Book)
1 Touch [ ] to change to the Contacts list screen. 2 Touch the name of the
contact or number you want to
call.
21-EN
3 Touch the phone number.
The Phone Operation screen is displayed.
4 Touch the number you want to call.
The phone call is started
Siri
Establish iPhone Bluetooth connection and wake up Siri from phone , below
interface will pop up and the voice output is from the unit.
22-EN
Phone Operation Screen
Adjusting the Speech Volume
You can adjust Mic. Level (Microphone Level). Level 1: Level 2: Level 3:
Changing the Voice Output
The voice output for calls is switchable between car speakers and the mobile
phone speaker. Touch [ ] or [ ].
DTMF (Touch-Tone) Function
Transmits a DTMF (Touch-Tone) during a call.
1 Touch [ ] (Keypad).
The number input screen (Keypad) appears.
2 Input number.
· You can transmit a Touch-Tone signal during a call.
Phone Book Function
Phone Book screen example
Synchronizing the Phone Book
Touch [ ]. Synchronization of the phone books starts. · You can store up to
1,000 registered name in the phone book. · You can store up to 5 phone numbers
by one person’s name.
Bluetooth® Audio
If a Bluetooth compatible mobile phone, portable player, etc. is connected by
wireless, you can play back a song (operation is controllable from the unit).
· Operation may vary, depending on the Bluetooth compatible device
Bluetooth Audio main screen example
A Default image display B Information display C Elapsed time/Total time for
playing D Search device E Shuffle mode F [ ]repeat_off,[ ]repeat_folder,[i
[ ]repeat_all G Finds the beginning of next chapter H Pause and Play I Finds
the previous file
]repeat_one,
· Song title/Artist title/Album title/Elapsed time do not display for AVRCP
Ver. 1.0.
· To play back audio, a mobile phone or a portable player conforming to A2DP
(Advanced Audio Distribution Profile) or AVRCP (Audio/Video Remote Control
Profile) is required. Not all functions work with all devices.
· During a call, sound on the Bluetooth audio source is paused.
Compatible AVRCP versions: 1.0, 1.3, 1.4, 1.5, 1.6.2
· Available functions may differ depending on the AVRCP version.
A Use to narrow down your search for names, etc. B You can synchronize the
system’s phone book with the
mobile phone’s phone book.
23-EN
Playback
1 Touch the (HOME) button and select Bluetooth
Audio mode. The display shows the Bluetooth Audio mode screen.
2 Touch [ ] or [ ] to select the desired track (file).
Returns the beginning of the previous file: Touch [ ].
Advance to the beginning of the next file: Touch [ ].
3 To pause playback, touch [ ].
Repeat Play
Available for AVRCP Ver. 1.0, 1.3, 1.4, 1.5, 1.6.2.
1 Touch [ ].
· [ ] displays the currently selected mode.
2 Select your desired Repeat mode.
The selected Repeat mode changes the button. ALL : Once all of the songs have
finished playing, play back is
repeated, starting with the first song. One : Only the track currently playing
is repeatedly played back. OFF : Repeat mode is Off.
· Operations may differ depending on the connected Bluetooth compatible
device.
AUX Operation (Optional)
AUX Operation
· Through AUX connection, you can display the videos or images output from
other devices
· For safety , video image can not be displayed when vehicle is moving. To
view the video image ,please stop in a safe zone and apply the parking brake.
· A mini AV cable is required to make the connection (sold separately) Further
details are given in <
AUX screen example
1 Touch [ ]. 2 Touch [AUX] Display AUX screen
Shuffle Play
Available for AVRCP Ver. 1.0, 1.3, 1.4, 1.5, 1.6.2.
Touch [ ].
· All songs in the Bluetooth compatible devices are played back in random
sequence. Any one song does not play back again until all songs have been
played back.
· Operations may differ depending on the connected Bluetooth compatible
device.
24-EN
Camera Operation (Optional)
Camera screen example
About the Rear Camera Guide
Indication mark meaning When the car is put into reverse gear, the monitor
switches to the rear view camera image. Guides appear to help visualize the
car’s width and distance from the rear bumper.
Setting item: Display Reverse video
Setting contents: Camera Guide Off (Initial setting) / On
· No impacts on other modes (except video ,video shall be suspended,When
playing the audio,the audio shall continue playing),Switch to this scree,other
modes to run in the background
Camera Operation
Displaying the Camera Image from the Menu screen
1 Touch the (HOME)button.
The HOME screen is displayed
2 Touch [Camera].
· Touch the screen while the camera image is being displayed, and touch [ ] to
return to the main source screen or previous screen.
· You can perform a Guide Adjustment for the rear view image. For details, see
“Rear Camera Setup” (page 39).
Displaying the rear view video while the car is in reverse
1 Shift the gear lever to the reverse (R) position.
The rear view image is displayed while the car remains in reverse.
2 If you shift the gear lever to a position other than
reverse (R), the monitor returns to the previous screen.
· Never depend solely on the camera when backing up. Always turn and look and
only use the camera for additional assistance.
· This function is effective when the reverse wire is properly connected. ·
You can perform a Guide Adjustment for the rear view image. For
details, see “Rear Camera Setup” (page 39).
Car width extension marks (red, yellow and green in order of distance) If
properly calibrated, the marks indicate the car’s width. This helps guide the
car’s path when backing up in a straight line.
The marks represent the distance from the rear of the car (from the rear end
of the bumper). · The marks do not move in synchronization with the steering
wheel. · Set the marks to suit the car’s width.
· Depending on the condition of the car or road surface, the range of vision
may vary.
· The camera has a limited range of vision. Objects at extreme angles to the
camera (e.g. under the bumper or at opposite ends of the bumper) may not be in
the its field-of-vision.
· The rear camera image may have a tint which is different from the actual
surroundings.
· Depending on the car, the guidance may deviate to the right or left. This is
not a malfunction.
25-EN
Sound Boost and Lighting link (Optional)
Lighting Link screen example
A Current screen On/Off B Sub.Woofer On/Off
Linkage with the Settings in sound (page 35) C Adjust Sub.Woofer Level
Linkage with the Settings in sound (page 35) D Sub.Woofer Phase
Linkage with the Settings in sound (page 35) 0° (Initial setting), 180° E
Lighting Link setting can change the LED color of the system model, the
keyColor of this unit, and the background color in tandem. F Displays sound
setup icon touch the icon to sound setup screen G Max Mid Bass On/Off Linkage
with the Settings in sound (page 33) H Max Bass On/Off Linkage with the
Settings in sound (page 33)
· If Lightinglink is OFF in the settings, this icon will not be displayed
(page 40).
Lighting Link Setting Operation
When operating the Lighting color of the system model with Lightinglink, it is
necessary to connect a model that supports Lightinglink. Check the Alpine
website for compatible models.
1 Touch [ ].
2 Touch [ ]Display Sound Boost screen
3 Touch [ ] Display Lighting Link screen
A LED On/Off LED OFF: Premium Direct Color and LED Brightness and LED Lighting
Speed, Other Color is grayed out and cannot be selected. And the Lighting of
the connected system turns off.
B Select Premium Direct Color Blue,Red,Amber,Green,White Each Lighting color
changes in conjunction. Please refer to page 27 for the changed parts and
their colors.
C Adjust LED Brightness Adjusts the brightness level of the LEDs on
Lightinglinkenabled models -3 – +3 Initial: 0
D Adjust LED Light Blinking Speed E Select Other Color
Select Premium Direct Color or Dynamic mode
LED Brightness Adjusts the brightness level of the LEDs on Lightinglink-
enabled models
Setting item: LED Brightness
Setting contents: -3~+3,0(Initial setting)
LED Lighting Speed Adjusts the level of LED Light Blinking Speed for
Lightinglink compatible models
Setting item: LED Lighting Speed
Setting contents: -5~+5,0(Initial setting)
Other Color
· Please connect the Lighting Link compatible model with the lighting level and speed setting values set to 0.
26-EN
Lighting Link settings Colors
· Lighting Link has 8 modes.
Lighting Link Setting Colors
Red
Lighting Link
& Sound boost background,
Red
Sub.W Ring Color
Key Color*
Red
Background
Red
Screen Color*
Premium Direct color select
Blue
Green
Amber
White
Other colors
7 colors
Dynamic Mode
LED OFF
Blue
Green
Amber
White Rainbow1 Rainbow2
–
Blue
Green
Amber
White
White
White
select
Blue
Green
Amber
White
White
White
User
- key Color and Background Screen Color is linked when Lighting Link is ON. Please see page 32. If you select a color with the Lighting Link function, it will all change to the selected color pattern regardless of
the current color settings for each. BackgroundScreen color and keyColor can be changed individually after setting Lighting Link (page 32).
· Lighting Link System model is option.
27-EN
Setup
Setup Operation
To display the Setup Menu screen: Your vehicle must be parked with the
ignition key in the ACC or ON position. To do this, follow the procedures
below.
1 Bring your vehicle to a complete stop at a safe location. Engage the parking
brake.
2 Release the parking brake. (For safety, release the parking brake while
depressing the foot brake pedal).
3 Engage the parking brake again.
· For automatic transmission vehicles, place the transmission lever in the
Park position.
· “Sound Setup” (page 33) can be set even not engaging the parking brake.
Now, the locking system for the Setup operation has been released. Engaging
the parking brake can reactivate the Setup Menu, as long as the car’s ignition
has not been turned off. It is not necessary to repeat the above procedure (1
through 3).
Each time the ignition is turned OFF, perform the above procedure.
1 Touch the (HOME) button.
The HOME screen is displayed.
[Setup] button
3 Touch the required setting list, then touch the setting
item.
Setting items: System: See “System Setup” (page 28). Screen/Lighting: See
“Screen//Lighting Setup” (page 32). Sound: See “Sound Setup” (page 33).
Volume: See “Volume Setup” (page 38). Bluetooth: See “Bluetooth Setup” (page
38). Rear Camera: See “Rear Camera Setup” (page 39). Lighting Link ON/OFF: See
“Lighting Link” (page 40).
System Setup
[System] is selected on the Setup menu screen.
Setting item: System
Setting contents: Beep, Language, Time Adjust,SiriusXM, Product Information,
Software License, Connection Status, Steering Wheel Control, Reset
2 Touch [Setup]button.
The Setup main screen is displayed.
Beep Setup You can change the volume of the sound heard when a button is
touched.
Setting item: Beep
Setting contents: Off , On (Initial setting)
- Touch [
] or [
] to show further hierarchies.
Scroll Bar
28-EN
Language Setup
[Language] is selected on the System Setup Menu screen. The Setup menu,
feedback information, etc. for this unit can be changed to appear in the
selected language.
Setting item: Language
Setting contents: English (US),French,Spanish,Portuguese
· The currently selected language is displayed.
SiriusXM Setup
Time Adjust Setup
[Time Adjust] is selected on the System Setup Menu screen.
Change Passcode
Setting item: Change Passcode
Setting contents: Edit the passcode.
1 Enter the current passcode and then touch [OK]. 2 Enter the new passcode and
then touch [OK]. 3 Enter the confirm passcode and then touch [OK].
Time Format
Setting item: Time Format
Setting items: 12h, 24h(Initial setting)
Time Zone
Setting item: Time Zone
Setting contents UTC-12.00h~UTC+14.00
Daylight saving Time ON/OFF
Setting item: Daylight saving Time
Setting contents Off (Initial setting), On
Parental Control
You can lock out channels with passcode protection. Channels that are locked
cannot be accessed without entering the passcode. You can unlock a channel or
change the passcode using this menu option.
Setting item: Parental Lock On/Off
1 Touch [Parental Control].
A passcode input screen is displayed.
2 Touch the numeric keypad to input a 4-digit passcode
The initial default 4-digit passcode is set to 0000.
After entering the digit, it is displayed as ” “. Touch [Clear] to delete all
entered numbers.
3 Touch [OK].
The channels list screen is displayed.
Setting the Lock status of individual channels
4 Touch [ Channels].
· To lock the channel,touch the appropriate channel. · When you touch the
locked channel,the channel is unlocked.
appears and the channel is locked.
29-EN
Clear Locked All
Product Information
Setting item: Clear Locked All
Setting contents: Off (Initial setting) / On
· Touch the switch,enter the current passcode then touch [OK]. · All stations
will be cleared when Off. Locking again will change to ON
automatically
Changing the Lock Passcode
1 Touch [Change Passcode].
The numeric keypad screen is displayed.
2 Use the keypad to enter the current (old) 4-digit
passcode, and then touch [OK]. The initial passcode is set to “0000.” After
entering the digit, it is displayed as . Touch [Clear] to delete all entered
numbers.
3 Use the keypad to enter the new 4-digit passcode, and
then touch [OK].
4 Use the keypad to enter the new 4-digit passcode a
second time to verify it, and then touch [OK]. Remember to keep a note of the
passcode in a safe place in case you forget the code.
Version
Setting item: Version
Setting contents: Model Brand,Model Number,Firmware Ver,HW Version.
Setting item: Model Number, MCU, SOC, Interface FW Version, Interface HW
Version
Updating the firmware version
1 Download the firmware update file into your computer. 2 Inset a USB with
FAT32 format into your computer,copy
the correct upgrade file to the root directory
3 Connect the USB storage device to this product. 4 Touch [setup]>[System
setup]>
[Product Information]>[Update] . The firmware update file information will be
read
5 After readingTouch[Update] Follow the on-screen prompts to update the
firmware. · This product will reset automatically after the firmware update is
completed if the update is successful. · If an error message on the
screen,Repeat the preceding steps
30-EN
Software License
[Software License] Displaying the open source software license.
Steering Wheel Control
Connection Status
GPS Antenna · Display when there is an antenna [OK] · Display without antenna
[NOK] Antenna: Yes Signal:0 Antenna: Yes Signal:1 Antenna: Yes Signal:2
Antenna: Yes Signal:3 Antenna: No Positioning Status · Display [position]:
When there is positioning · Display [Not Available]: When there is no
positioning · Display [Not Connected]: When the serial port of the GPS module
is not available Installation · Install and learn to successfully display
[OK], · No learning success display [NOK] Speed Pulse · Display pulse number
“XXX” in unit time, and display “0” if not obtained.
Some Vehicles may require a 3rd party module to achieve steering wheel control functions (Sold Separately)
Setting item: Steering Wheel Control key learning
Setting contents: Vol. Up/ Vol. Dn, ON HOOK, Seek Up, Seek Dn, MUTE,
Voice Recognition, Source (Mode)
OFF HOOK, Play/pause,
1 Please press and hold key for 2s at the same time don’t
press SWC key within 2s
2 Follow the on-screen prompts to complete the operation
3 Key Learning Success:
When operation finished ,If you want to continue other key learning , please
repeat the operation
· Please perform key learning while parked with e-brake active.
· Keys only support learning 1 time. If you need to change the key please clear all learned keys.
· Touch the clear key to clear all the learned function.
· No time limit for key learning.
Reset
[Reset] is selected on the System Setup Menu screen. You can initialize all
data, to restore the factory settings.
Setting item: Reset
1 Touch [Reset]. 2 After the confirmation message appears, touch [Yes].
The system starts initialization.
· Do not turn on/off the power, change the ignition key position or until
system restart is completed.
31-EN
Screen/Lighting Setup
Screen Color
Setting item: Screen/Lighting
Setting contents: Dimmer,ScreenBrightness(Day),ScreenBrightness(Night), Screen
Color, Key Color
Dimmer
You can set day, night and auto three modes in dimmer
1. The screen backlighting brightness can be set in day/night mode 2. Auto
Mode adjusts the backlighting brightness to the appropriate
day/night brightness setting value based on the current ambient brightness
Setting contents: Day,Night,Auto(Initial setting)
Day: The backlight brightness is adjusted by setting the screen brightness
setting(Day)
Night: The backlight brightness is adjusted by setting the screen brightness
setting(night)
Auto: Automatically adjust the backlight brightness and select the Screen
brightness(Day) or Screen Brightness (Night) setting value as the backlight
brightness value based on the Day/Night lighting threshold
Screen Brightness(Day)
Setting item: Level
Setting contents: 1 to 32
Screen Brightness(Night)
Setting item: Level
Setting contents: 1 to 32
Setting item: Background Picture
Setting contents: You can set blue, red, amber, green, white five colors or
other background pictures, you can also select the background picture to be
set from the USB flash drive
Setting item: Background custom
1 Insert a USB flash drive. 2 Touch [ ] to the Wallpaper screen. 3 Select the
custom picture.
Setting item: Color Link (Key/Screen)
Setting contents: Color link ON (Initial setting)
· You can select ON/OFF whether the button light and background picture
linkage.
Key Color
Setting item: Key Color
Setting contents: blue, red, amber, green, white
· Key color Settings can be set blue, red, amber, green, white five colors ·
When the Color Link is ON, key Color is grayed out and cannot be
selected. · When the Lighting Link function is used, that selection takes
precedence
and all colors are switched (page 27). · You can change the Key Color
individually after selecting the color with
the Lighting Link function.
32-EN
Sound Setup
[Sound] is selected on the Setup menu screen. You can set up items related to
the sound quality.
Fader/Balance (page 33) Bass/Treble (page 33) EQ Setting (page 33) Preset EQ
(page 34)
X-Over (page 35) Speaker Level (page 36) Time Correction (page 35) Sub Woofer
(page 35) Defeat (page 36) * Touch [ ] or [ ] to show further .
Setting the Fader/Balance
Adjusting the Bass/Middle/Treble
Touch [ ] or [ ] for each item to be adjusted. Setting item:
Bass, Middle, Treble Setting contents:
-12 to 12 (Initial setting: 0) · To reset the initial setting (Bass: 0, Middle: 0, Treble: 0), touch [Flat]. · When the Defeat setting is [On], you cannot perform the set up.
Adjusting the Graphic Equalizer Curve (EQ)
Setting item: EQ
· When the Defeat setting is [On], you cannot perform the set up.
1 Adjust the EQ to your preference.
A Back Exit[Fader/Balance]Return [SOUND].
B Close Close the current screen and return to the source screen
C Fader/Balance Image area Touch the desired point within the image area, or
touch [ ], [ ], [ ] or ].
Fader: [15]Front to [15]Rear
Balance: [15]Left to [15]Right
· To reset to the initial setting (Fader: F=R, Balance: L=R), touch [ ].
Adjusting the Band Touch [Band] to select the band to be adjusted. Band1 Band2
··· Band8 Band13 Band1 · You can select a band directly by touching the
screen.
Adjusting the Frequency Touch of “Frequency” to adjust the frequency of the
selected band
33-EN
Adjustable frequency bands: Band1: 50 Hz Band2: 80 Hz Band3: 125 Hz Band4: 200
Hz Band5: 315 Hz Band6: 500 Hz Band7: 800 Hz Band8: 1.25k Hz Band9: 2k Hz
Band10: 3.15k Hz Band11: 5k Hz Band12: 8k Hz Band13: 12.5k Hz
Adjusting the Level
1 Select Band Slide up or down to adjust the level of
selected band.
Setting contents: -12 to 12 (Initial setting: 0)
2 To adjust another band, repeat step 1, and adjust all
bands.
3 To store the adjusted setting value, touch and hold
[Preset 1], [Preset 2], or [Preset 3] for at least 2 seconds.
· Band2, Band7 and Band12 are the same as the Bass and Middle controls. For
details on setting Bass and Treble, see “Adjusting the Bass/ Middle/Treble”
(page 33).
· Settings exceeding the frequency of adjacent bands are not available · While
adjusting the EQ Setting, you should consider the frequency
response of the connected speakers. · When you apply the adjusted Band in the
EQ setting screen,Preset EQ
(page 34) is unselected · Touch [Flat] to initialize all values.
Calling the EQ Setting adjusted value Calling the pre-set EQ Setting adjusted
value.
Touch [Preset 1], [Preset 2], or [Preset 3] on the EQ Setting screen. The
setting stored in the Preset will be recalled.
Setting an Equalizer
6 typical equalizer settings are preset at the factory for a variety of
musical source material. You can also preset an equalizer by customizing.
Setting item: Preset EQ
Setting contents: Flat (Initial setting), Hip Hop/R&B, Rock, Easy Listening,
Pop, Bass Boost Mid Bass Boost
· When the Defeat setting is [On], you cannot perform the set up. · Only one
type can be set . · you can set [preset1/preset2/preset3 ]in the EQ setting
screen. (page
33) · When you set [preset1/preset2/preset3 ]in the EQ setting screen.(page
33). Preset EQ is unselected
34-EN
Setting the Subwoofer
Adjusting the Crossover Settings (X-Over)
Before performing the following procedures, see “About the Crossover” (page
36).
Turning Subwoofer ON/OFF If an optional subwoofer is connected to the unit,
make the following setting.
Setting item: Sub Woofer
Setting contents: Off (Initial setting), On
Adjusting the Subwoofer Level
Setting item: Level
Setting contents: 0 (Initial setting) to 15
· This setting is only available when “Sub Woofer” is set to [On].
Setting the Subwoofer Phase The subwoofer output phase is toggled Subwoofer
Normal (0°) or Subwoofer Reverse (180°).
Setting item: Phase
Setting contents: 0° (Initial setting), 180°
· This setting is only available when “Sub Woofer” is set to [On].
Selecting the Front HPF
Setting item: Front HPF
Setting contents: Off (Initial setting)/ 25 / 32 / 40 / 50 / 63 / 80 / 100 /
125 / 160 / 200 / 250 Hz
Selecting the Rear HPF
Setting contents: Rear HPF
Setting contents: Off (Initial setting)/ 25 / 32 / 40 / 50 / 63 / 80 / 100 /
125 / 160 / 200 / 250 Hz
Selecting the LPF
Setting contents: LPF
Setting contents: Off (Initial setting)/ 25 / 32 / 40 / 50 / 63 / 80 / 100 /
125 / 160 / 200 / 250 Hz
· This setting is only available when “Sub Woofer” is set to [On].
Adjusting the Time Correction (TCR)
Before performing the following procedures, see “About Time Correction” (page
37).
Setting item: TCR
Touch [ ] or [ ] for each speaker to adjust the time . 0.0 msec to 10.0 msec
(0.1 msec/step)
· If the Subwoofer setting is [Off], the Subwoofer setting cannot be edited
(page 35).
35-EN
Setting the Speaker Level
Setting item: Speaker Level
Touch [ ] or [ ] for each speaker to adjust the Speaker. -24dB to 10dB (0.1
dB/step)
Setting Defeat
If Defeat is [On], the EQ and Equalizer setting are turned Off. This disables
any settings made for these functions. Setting item:
Defeat Setting contents:
Off (Initial setting) / On
About the Crossover
Crossover (X-Over): This unit is equipped with an active crossover. The crossover limits the frequencies delivered to the outputs. Each channel is controlled independently. Thus, each speaker pair can be driven by the frequencies for which they have been optimally designed.
The crossover adjusts the HPF (high pass filter) or LPF (low pass filter) of each band.
Adjustments should be made according to the reproduction characteristics of the speakers. Depending on the speakers, a passive network may not be necessary. If you are unsure about this point, please consult your authorized Alpine dealer. 25 Hz, 32Hz, 40Hz, 50Hz, 63Hz, 80Hz
Cut-off frequency
HPF
LPF
Subwoofer (LPF)
25Hz, 32Hz, 40Hz, 50Hz,
—
63Hz, 80Hz 100Hz, 125Hz, 160Hz,
200Hz, 250Hz
25Hz, 32Hz, 40Hz, 50Hz,
Rear speaker
63Hz, 80Hz
(HPF)
100Hz, 125Hz, 160Hz,
—
200Hz, 250 Hz
Front speaker (HPF)
25Hz, 32Hz, 40Hz, 50Hz, 63Hz, 80Hz
100Hz, 125Hz, 160Hz, 200Hz, 250Hzz
—
· HPF (high pass filter): Cuts the lower frequencies and allows the higher
frequencies to pass.
· LPF (low pass filter): Cuts the higher frequencies and allows the lower
frequencies to pass.
· Do not use a tweeter without the HPF on or set to a low frequency, as it may
cause damage to the speaker due to the low frequency content.
· Adjustment should be made according to the recommended crossover frequency
of the connected speakers. Determine the recommended crossover frequency of
the speakers. Adjusting to a frequency range outside that recommended may
cause damage to the speakers. For the recommended crossover frequencies of
Alpine speakers, refer to the respective Owner’s Manual. We are not
responsible for damage or malfunction of speakers caused by using the
crossover outside the recommended value.
36-EN
About Time Correction
The distance between the listener and the speakers in a car vary widely due to
the complex speaker placement. This difference in the distances from the
speakers to the listener creates a shift in the sounds image and frequency
characteristics. This is caused by the time delay between the sound reaching
the listener’s right versus the left ear. To correct this, this unit is able
to delay the audio signal to the speakers closest to the listener. This
effectively creates a perception of increased distance for those speakers. The
listener can be placed at an equal distance between the left and right
speakers for optimum staging. The adjustment will be made for each speaker in
3.4 cm steps.
Example 1. Listening Position: Front Left Seat
Adjust the time correction level of the front left speaker to a high value and
the rear right to zero or a low value.
The sound is not balanced because the distance between the listening position
and the various speakers is different. The difference in distance between the
front left speaker and the rear right speaker is 1.75 m (68-7/8″). Here we
calculate the time correction value for the front left speaker in the diagram
on the above.
Conditions: Farthest Speaker listening position : 2.25 m (88-9/16″) Front
left speaker listening position : 0.5 m (19-11/16″) Calculation: L = 2.25 m
0.5 m = 1.75 m (68-7/8″) Time correction = 1.75 ÷ 343 × 1,000 = 5.1 (ms)
Speed of sound: 343 m/s (765 mph) at 20°C In other words, giving the front
left speaker a time correction value of 5.1 ms makes it seem as if its
distance from the listener is the same as the distance to the farthest
speaker. Time correction eliminates the differences in the time required for
the sound to reach the listening position. The time of the front left speaker
is corrected by 5.1 ms so that its sound reaches the listening position at the
same time as the sound of other speakers.
Example 2. Listening Position: All Seats
Adjust the time correction level of each speaker to almost the same level.
1 Sit in the listening position (driver’s seat, etc.) and
measure the distance (in meters) between your head and the various speakers.
2 Calculate the difference between the distance correction
value to the farthest speaker and the other speakers.
L = (distance to farthest speaker) (distance to other speakers)
These values are the time correction values for the different speakers.
Setting these values to make each sound reach the listening position at the
same time as the sound of other speakers.
Time Correction Value List
Time Difference
(msec) 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2 1.3 1.4 1.5 1.6 1.7
1.8 1.9 2.0 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 3.0 3.1 3.2 3.3 3.4 3.5 3.6
3.7 3.8 3.9 4.0 4.1 4.2 4.3 4.4 4.5 4.6 4.7 4.8 4.9 5.0
Distance (cm)
0.0 3.4 6.8 10.2 13.6 17.0 20.4 23.8 27.2 30.6 34.0 37.4 40.8 44.2 47.6 51.0
54.4 57.8 61.2 64.6 68.0 71.4 74.8 78.2 81.6 85.0 88.4 91.8 95.2 98.6 102.0
105.4 108.8 112.2 115.6 119.0 122.4 125.8 129.2 132.6 136.0 139.4 142.8 146.2
149.6 153.0 156.4 159.8 163.2 166.6 170.0
Distance (inch)
0.0 1.3 2.7 4.0 5.4 6.7 8.0 9.4 10.7 12.1 13.4 14.7 16.1 17.4 18.8 20.1 21.4
22.8 24.1 25.5 26.8 28.1 29.5 30.8 32.2 33.5 34.8 36.2 37.5 38.9 40.2 41.5
42.9 44.2 45.6 46.9 48.2 49.6 50.9 52.3 53.6 54.9 56.3 57.6 59.0 60.3 61.6
63.0 64.3 65.7 67.0
Time Difference
(msec) 5.1 5.2 5.3 5.4 5.5 5.6 5.7 5.8 5.9 6.0 6.1 6.2 6.3 6.4 6.5 6.6 6.7 6.8
6.9 7.0 7.1 7.2 7.3 7.4 7.5 7.6 7.7 7.8 7.9 8.0 8.1 8.2 8.3 8.4 8.5 8.6 8.7
8.8 8.9 9.0 9.1 9.2 9.3 9.4 9.5 9.6 9.7 9.8 9.9
Distance (cm)
173.4 176.8 180.2 183.6 187.0 190.4 193.8 197.2 200.6 204.0 207.4 210.8 214.2
217.6 221.0 224.4 227.8 231.2 234.6 238.0 241.4 244.8 248.2 251.6 255.0 258.4
261.8 265.2 268.6 272.0 275.4 278.8 282.2 285.6 289.0 292.4 295.8 299.2 302.6
306.0 309.4 312.8 316.2 319.6 323.0 326.4 329.8 333.2 336.6
Distance (inch)
68.3 69.7 71.0 72.4 73.7 75.0 76.4 77.7 79.1 80.4 81.7 83.1 84.4 85.8 87.1
88.4 89.8 91.1 92.5 93.8 95.1 96.5 97.8 99.2 100.5 101.8 103.2 104.5 105.9
107.2 108.5 109.9 111.2 112.6 113.9 115.2 116.6 117.9 119.3 120.6 121.9 123.3
124.6 126.0 127.3 128.6 130.0 131.3 132.7
37-EN
Volume Setup
Volume Setup
[Volume] is selected on the Setup menu screen.
Setting item: Main.Ring Vol.Talking.Voice/Navi Guidance.TA
Setting contents: Main :01 to 35(Initial setting: 10) Ring Vol :01 to
35(Initial setting: 18) Ring Vol :01 to 35(Initial setting: 18) Voice/Navi
Guidance :01 to 35(Initial setting: 18) TA :01 to 35(Initial setting: 10)
Bluetooth Setup
[Bluetooth] is selected on the Setup menu screen. Setting item:
Bluetooth Setting contents:
Bluetooth,Devices List, Devices Info,
Bluetooth · You can turn Bluetooth on or off
Device List
[Devices] is selected on the Bluetooth Setup Menu screen. You can register and
set up Bluetooth compatible devices.
Pairing the Bluetooth Device
1 Touch [ ] to enter [Search] screen to search for
Devices.
2 Select a device and follow the on-screen prompts to
connect devices
3 Screen prompts 6 character Numeric passkey to pair
When the device registration is complete, a message appears and the device
returns to [Device List].
· The Bluetooth registration process differs depending on the device version
and SSP (Simple Secure Pairing). If a 4 or 6 character Numeric Comparison
appears on this system, enter the Numeric Comparison on the Bluetooth device.
· If a 6 character Passkey appears on this system, make sure the same passkey
is displayed on the Bluetooth device, and follow the screen.
Fast pairing the Bluetooth Device
Select one of 5 paired Bluetooth compatible devices that you previously
registered.
1 Touch [Connect] on the Bluetooth Setup Menu screen.
Deleting a Bluetooth Device from the list
You can delete the information of a previously connected Bluetooth compatible
device.
1 Touch [ ] on the Bluetooth Setup Menu screen. 2 Touch [Yes].
· Touching [No] will cancel the setting.
Searching for a Bluetooth Device
Setting item: Search
1 Touch [ ] on the device list interface in Bluetooth
Setup. The Bluetooth devices can be searched are displayed in a list.
2 Touch the device you want to connect from the list.
You can register up to 5 Bluetooth compatible mobile phones.
3 When the device registration is complete, a message
appears and the device returns to [Device List].
· Connect to new Bluetooth compatible device when there are 5 paired devices
registered , the system will delete the last paired device automatically
38-EN
Displaying Bluetooth Information
[Info] is selected on the Bluetooth Setup Menu screen. You can display the
Bluetooth device name and device address of this unit.
Rear Camera Setup
[Camera] is selected on the Setup Menu screen. You can set up items related to
the Rear Camera.
Setting item: Rear Camera
Setting contents: Camera,Mute While Backing Up, Parking Guide Adjust,Video
Setup
Auto Connection
When the ACC is turned ON, the Bluetooth Hands-Free device is automatically
connected. After connecting to the Hands-Free device, the Bluetooth Audio
device is also connected automatically.
Downloading the Phonebook
If PBAP is connected, you can download the phonebook from the device. · When
the device is disconnected, the downloaded phonebook is not
shown.
Camera
Setting item: Camera
Setting contents: Off, On (Initial setting),
· The rear camera initial setting is ON , when you turn off the camera , you
cannot open and setup the camera.
Mute While Backing Up
Setting item: Mute While Backing Up
Setting contents: Off (Initial setting), On ,
Parking Guide Adjust Setup
You can adjust the camera guide position.
Setting item: Parking Guide Adjust
Setting contents: Touch the icon you want to move.
1 Touch the icon you want to move. 2 Touch [ ] [ ] [ ] [ ]to move the icon.
Touching [Reset] clears adjustments and returns to the setting before guide
line alteration.
3 Touch [ ]to complete the adjustment and return to the
previous screen.
39-EN
Video Setup
Lighting Link ON/OFF
[Lighting link] is selected on the Setup menu screen.
Adjusting Brightness
Setting item: Brightness
Setting contents: -10 to 10 (Initial setting: 0)
· You can adjust the brightness of USB Video and reverse video between
MIN(-10)and MAX(10)
Adjusting Color of Display
Setting item: Colors
Setting contents: -10 to 10 (Initial setting: 0)
· You can adjust the color of USB Video and reverse video between MIN(-10)and
MAX(10)
Adjusting Display Contrast
Setting item: Contrast
Setting contents: -10 to 10 (Initial setting: 0)
· You can adjust the Contrast of USB Video and reverse video between
MIN(-10)and MAX(10)
Setting item: Lighting Link
Setting contents On: Lighting link icon displayed on sound boost screen
Off: The Lighting link icon on the sound boost screen is not displayed
40-EN
Distance guidance mark
The distance guides represent the ground level distance from the rear bumper.
It is difficult to accurately estimate the distance to objects above ground
level.
In the following example, the distance to A is 0.5 m and the distance to B is
1 m.
<Positions of A, B and C> about 1 m
C B A (about 0.5 m)
Actual distances
Error Error
The distance guidance mark represents the distance to a flat road surface.
Therefore in the case of an upward slope behind the car, the distance guides
are displayed closer to the rear bumper than the actual distance. For example,
if there is an obstacle on the upward slope, it may appear farther away than
its actual position. Also, an error may occur between the guidance and the
actual path of the car on the road surface.
When there is a steep downward slope behind the car (example)
In the screen, according to the distance guidance marks, the truck seems to be
parked about 1 m away (at the position B). In actual fact, however, if you
reversed to position A, you would collide with the truck. In the screen,
positions A, B and C seem to be located in order of proximity. However, in
actual fact, the position A and C are the same distance, and B is farther away
than positions A and C.
· The car width extension mark represents the distance to the road surface.
The distance to an object on the road is not accurately represented by the
guides.
Error between the screen and the actual road surface In the following
conditions, errors are produced between the screen guidance and the actual
road surface. (The illustrations represent a case when the camera is installed
in the standard position.)
When there is a steep upward slope behind the car (example)
Distance guidance marks
41-EN
Information
About the Supported Formats
CAUTION Except for private use, duplicating audio data or distributing,
transferring, or copying it, whether for free or for a fee, without permission
of the copyright holder is strictly prohibited by the Copyright Act and by
international treaty.
About Audio Format
Method for creating WAVE/WMA/AAC/AC3/MPEG/Ogg/FLAC/ APE (USB Flash drive)
files
Audio data is compressed using software with WAVE/WMA/AAC/
AC3/MPEG/Ogg/FLAC/APE (USB Flash drive) codecs. For details on creating
WAVE/WMA/AAC/AC3/MPEG/Ogg/FLAC/APE(USB Flash drive files, refer to the user’s
manual for that software. WAVE/WMA/AAC/AC3/MPEG/Ogg/FLAC/APE (USB Flash drive)
files that are playable on this device have the file extensions.
WAVE:.WAV WMA:.WMA,.asf AAC:.aac AC3:.ac3,.ec3 MPEG:.mp1,mp2,mpa,mp3,.mp4,m4a
Ogg:.ogg FLAC:.flac APE:.ape
WMA is not supported for the following files, Windows Media Audio
Professional, Windows Media Audio 10 std or Windows Media Audio 10 Pro
Lossless.
There are many different versions of the AAC format. Confirm that the software
being used conforms to the acceptable formats listed above. It’s possible that
the format may be unplayable even though the extension is valid. Playback of
AAC files encoded by iTunes is supported.
WAVE (USB Flash drive)
F
References
- Shop SiriusXM
- COMERCIAL TIER
- Alpine | Car Audio, Stereo, Speakers, Subwoofers, and Amps
- Alpine | Car Audio, Stereo, Speakers, Subwoofers, and Amps
- Alpine | Support
- Alpine Terms of Use
- Terms of Use｜Alpine Electronics, Inc.
- SiriusXM is Loading
- SiriusXM: Music, Sports, Talk & Podcasts, Live & On Demand
- Activate Now | SiriusXM
- Weblink Desktop
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>