hama P2223185 Power Strip Instruction Manual
- June 13, 2024
- Hama
Table of Contents
hama P2223185 Power Strip
Operating instruction
Thank you for choosing aHama product. Take your time and read the following instructions and information completely. Please keep these instructions in asafe place for futurereference.
Explanation of warning symbols and notes
Risk of electricshock
This symbol indicates arisk of electric shock from touching product parts
carrying hazardous voltage.
Warning
This symbol is used to indicate safety instructions or to draw your
attention to specifichazards and risks.
Note
This symbol is used to indicate additional information or important notes.
Package contents
- Power strip
- These operating instructions
Safety instructions
- Use the product only for the intended purpose.
- Donot operate the product outside the power limits specified in the technicaldata.
- Protect the product from dirt, moistureand overheating and use it in dry environments only.
- Donot use the product in adamp environment and avoid splashing water.
- Donot continue to operate the product if it is visibly damaged.
- Donot bend or crush the cable.
- Donot drop the product anddonot exposeitto any major shocks.
- Always pulldirectly on the plug when disconnectingthe cable, never on the cable itself.
- Aswith allelectrical products, this device should be kept out of the reach of children.
- Dispose of packaging material immediately in accordance with the locally applicable regulations.
- Donot modify the product in any way.Doing so voids the warranty.
- The product is intended for private, non-commercial use only.
- The product is intended only for use inside buildings.
- Donot use the product in the immediate vicinity of heaters, other heat sources or in direct sunlight.
- Only use the article under moderate climatic conditions.
- Donot use the product in areas in which electronic products arenot permitted.
- Route allcables so that thereisnorisk of tripping.
- Never connect multiple units of this product in series.
- The product must only be operated on asupply network as described on thetype plate.
Risk of electric shock
- Do not open the device or continue to operate it if it becomes damaged.
- Do not use the product if the AC adapter, the adapter cable or the mains cable are damaged.
- Do not attempt to service or repair the product yourself. Leave any and all service work to qualified experts.
Warning
- Only operate the product from a socket that has been approved for the device. The socket must be installed close to the product and must be easily accessible.
- Disconnect the product from the power supply using the On/Off switch – if this is not available, unplug the power cord from the socket.
- If using a multi-socket power strip, make sure that the total power consumption of all connected devices does not exceed the power strip’s maximum throughput rating.
- If you will not be using the product for a prolonged period, disconnect it from mains power.
USB operation
Warning – Connection of devices
- Before connecting a device, check whether it can be adequately supplied with the charger’s current delivery.
- Ensure that the total output of all the connected devices does not exceed 18 W.
- Note the instructions in your device’s operating manual.
Note – Power Delivery
- Plug & GO: no additional software required, simply plug in and start: Thanks to Power Delivery the voltage and power are adjusted automatically.
- Be aware that, for efficient and optimised charging, your terminal device must support the PD (Power Delivery) function.
- If you have a large number of PD-enabled devices with different firmware updates, it may be that the function is not fully supported.
Unless different instructions have been expressly given in the operating instructions for the devices you are charging, proceed as follows:
- Connect your device to a USB charging port using a suitable USB cable.
- Connect the charger to a properly installed and easily accessible mains socket.
- The charging process is displayed on your device.
- Disconnect the device from the charger if you wish to interrupt the charging process or when the device is fully charged.
- Then disconnect the charger from the line connection.
Care and maintenance
Note
Disconnect the device from the mains before cleaning and during prolonged
periods of non-use.
- Only clean this product with a slightly damp, lint-free cloth and do not use aggressive cleaning agents.
- Ensure that no water is able to enter the product.
Warranty disclaimer
Hama GmbH & Co KG assumes no liability and provides no warranty for damage resulting from improper installation/mounting, improper use of the product or from failure to observe the operating instructions and/or safety notes.
Technical data
Mains connection | 250 V~ / 16A |
---|---|
Connected load | max. 3680 W |
Specifications according to Regulation (EU) 2019/1782
Brand name, commercial register
number, address
| Hama, HRA12159,
Dresdner Str. 9,
86653 Monheim, Germany
Model identifier| 00223185 / 00223186
Input voltage| 250 V
Input AC frequency| 50 Hz
Output voltage / output current / power output
| Total: 18,0W USB-A:
4,2V-6,0V/3,0A/12,6W-18,0W
6,0V-9,0V/2,0A/12,0W-18,0W
9,0V-12,0V/1,5A/13,5W-18,0W USB-C (PD):
5,0V/3,0A/15,0W
9,0V/2,0A/18,0W
12,0V/1,5A/18,0W USB-A+ USB-C:
2x 5,0V/1,8A/9,0W
Average efficiency
during operation
| 82,4 %
Efficiency at low
load (10%)
| 80,4 %
Power consumption
at zero load
| 0,10 W
Hama GmbH & Co KG 86652 Monheim/ Germany
Service & Support
- www.hama.com
- +49 9091 502-0
All listed brands are trademarks of the corresponding companies. Errors and omissions excepted, and subject to technical changes. Our general terms of delivery and payment are applied.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>