hama D3 223861 Power Strip Instruction Manual
- June 13, 2024
- Hama
Table of Contents
hama D3 223861 Power Strip Instruction Manual
Operating instruction
Thank you for choosing a Hama product. Take your time and read the following instructions and information completely. Please keep these instructions in a safe place for future reference.
Explanation of warning symbols and notes
Risk of electric shock
This symbol indicates a risk of electric shock from touching product parts
carrying hazardous voltage.
Warning
This symbol is used to indicate safety instructions or to draw your attention
to specific hazards and risks.
Note
This symbol is used to indicate additional information or important notes.
Package contents
- Power strip
- These operating instructions
Safety instructions
- Use the product only for the intended purpose.
- Do not operate the product outside the power limits specified in the technical data.
- Protect the product from dirt, moisture and overheating and use it in dry environments only.
- Do not use the product in a damp environment and avoid splashing water.
- Do not continue to operate the product if it is visibly damaged.
- Do not bend or crush the cable.
- Do not drop the product and do not expose it to any major shocks.
- Always pull directly on the plug when disconnecting the cable, never on the cable itself.
- As with all electrical products, this device should be kept out of the reach of children.
- Dispose of packaging material immediately in accordance with the locally applicable regulations.
- Do not modify the product in any way. Doing so voids the warranty.
- The product is intended for private, noncommercial use only.
- The product is intended only for use inside buildings.
- Do not use the product in the immediate vicinity of heaters, other heat sources or in direct sunlight.
- Only use the article under moderate climatic conditions.
- Do not use the product in areas in which electronic products are not permitted.
- Route all cables so that there is no risk of tripping.
- Never connect multiple units of this product in series.
- The product must only be operated on a supply network as described on the type plate.
Risk of electric shock
- Do not open the device or continue to operate it if it becomes damaged.
- Do not use the product if the AC adapter, the adapter cable or the mains cable are damaged.
- Do not attempt to service or repair the product yourself. Leave any and all service work to qualified experts.
Warning
- Only operate the product from a socket that has been approved for the device. The socket must be installed close to the product and must be easily accessible.
- Disconnect the product from the power supply using the On/Off switch – if this is not available, unplug the power cord from the socket.
- If using a multi-socket power strip, make sure that the total power consumption of all connected devices does not exceed the power strip’s maximum throughput rating.
- If you will not be using the product for a prolonged period, disconnect it from mains power.
USB operation
Warning – Connection of devices
- Before connecting a device, check whether it can be adequately supplied with the charger’s current delivery.
- Ensure that the total output of all the connected devices does not exceed 17 W.
- Note the instructions in your device’s operating manual.
Note – Power Delivery
- Plug & GO: no additional software required, simply plug in and start: Thanks to Power Delivery, the voltage and power are adjusted automatically.
- Be aware that, for efficient and optimised charging, your terminal device must support the PD (Power Delivery) function.
- If you have a large number of PD-enabled devices with different firmware updates, it may be that the function is not fully supported.
Unless different instructions have been expressly given in the operating instructions for the devices you are charging, proceed as follows
- Connect your device to a USB charging port using a suitable USB cable.
- The charging process is displayed on your device.
- Disconnect the device from the charger if you wish to interrupt the charging process or when the device is fully charged.
Troubleshooting
The socket is not live. Check the domestic fuse.
Changing the fuse:
- Prize out the mains plug cover (10) using the cutouts (11) by means of a suitable screwdriver.
- Remove the fuse (12) and replace it with a new one.
- Reattach the mains plug cover (10).
Care and maintenance
Note
Disconnect the device from the mains before cleaning and during prolonged
periods of non-use.
- Only clean this product with a slightly damp, lint-free cloth and do not use aggressive cleaning agents.
- Ensure that no water is able to enter the product.
Warranty disclaimer
Hama GmbH & Co KG assumes no liability and provides no warranty for damage resulting from improper installation/mounting, improper use of the product or from failure to observe the operating instructions and/or safety notes.
Technical data
Mains connection: 250 V ~ / 13 A
Connected load: max. 3250 W
Model identifier: D3223861 / D3223862
Input voltage: 250 V
Input AC frequency: 50Hz
Max. current strength: 13 A
Size: 6.3 x 25.4 mm
Service & Support
+49 9091 502-0
All listed brands are trademarks of the corresponding companies. Errors and omissions excepted, and subject to technical changes. Our general terms of delivery and payment are applied.
- Hama Gulf FZE, LB 19 2505, Jafza View 19, Downtown Jebel Ali, P.O Box:262174, Dubai, UAE.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>