hama SIRIUM2100AMBT Smart Speaker User Manual

“SIRIUM2000AMBT/SIRIUM2100AMBT” Smart Speaker
Smart-Speaker “SIRIUM2000AMBT/SIRIUM2100AMBT”

SIRIUM2100AMBT Smart Speaker

Operating Instructions
00054881
00054886
(SIRIUM2000AMBT)
00054882
00054887
(SIRIUM2100AMBT)

A: Loudspeaker top

B: Loudspeaker front

1. Status LED
2. Status LED update

C: Loudspeaker back

Behaviour of the LED indicator

is starting and searching for a network connection. Wait until the LEDs light up solid and the network connection has been established.
**Network indicator| **| Lights up solid green| The WLAN connection has been established successfully.
**| LED 1-3 flashing slowly red , LED 5 flashing slowly green| There is no connection with the network. Initial setup can be carried out via the Hama Smart Audio App.
**| LED 1-3 flashing quickly red , LED 5 flashing quickly green| There is no connection with the network. WPS mode is active.
**Amazon Alexa voice assistant| **| Alternating quick flashes of

blue and cyan

| Alexa is processing and responding to a voice command. No further voice commands can be given.
**| Lights up solid red| Mute mode is active. All microphones are muted. Alexa does not respond to the activation word.
**| Flashes red| There is no connection with the Amazon server. Alexa is unable to accept voice commands.

**Audio source indicator**

**** (If the volume is muted in this mode, the LED flashes in the relevant colour)

| **| Pulses blue| The loudspeaker is in Bluetooth mode. There is no connection with a mobile device.
**| Flashes blue| The loudspeaker is in Bluetooth pairing mode. The first connection can be established with a mobile device.
**| Lights up solid blue| The loudspeaker is in Bluetooth mode. A connection has been successfully established with a mobile device.
**| Lights up solid purple| The loudspeaker is in optical mode. A device can be connected via the digital input
**| Lights up solid orange| The loudspeaker is in USB mode. An external storage medium can be connected.
**| ****

Lights up solid cyan

| The loudspeaker is in AUX mode. A device can be connected via the analogue input. Audio data can be played back via AUX In.
**Volume indicator| **| Lights up white for 3s| Volume 20%
**| Lights up white for 3s| Volume 40%
**| Lights up white for 3s| Volume 60%
**| Lights up white for 3s| Volume 80%
**| Lights up white for 3s| Volume 100%

Note

• Forreasons of environmental protection and to save valuable rawmaterials, the brightness of the LED is dimmed after 15 minutes of no commands being issued. If acommand is then issued, the brightness of the LED display is restored to its original setting.

00054881/00054886 SIRIUM2000AMBT
Technical Data

Alexa Voice Service

Voice control|
Number of microphones| 3
Microphone array| Far field
Bluetooth

WiFi (standard); (encryption, WPS)| Dual Band 2.4 GHz (b/g/n) & 5 GHz (a/c) MiMo 1×1 WiFi
Bluetooth (standard)| 4.1 Low Energy (BLE)
USB| Playback & update
Digital optical IN|
AUX-IN|
Line-Out|
Other details and speci fi cations

Remote control| Hama SRC-1805 Layout B
Batteries| 2x AAA
Option for wall hanging|
Size (W xHx D)| 27 cm x 14.5 cm x 16.5 cm
Weight| 2.2 kg
Equaliser / DSP

Pro fi les| 2 (Standard and My Equaliser)
Standards & decoders

Max. sound resolution (Hi-res)| 192 kHz / 24 bit
Hi-res audio codecs supported| FLAC, ALAC
Online update| Forced / manual update
Streaming

WiFi stream (DLNA compatible)|
UPnP|
Loudspeaker

2x mid-woofer| 3″ (7.62 cm)
2x tweeter| 20 mm
Ampli fi er class| Class D (TAS5754)

00054882/00054887 SIRIUM2100AMBT
Technical Data

Alexa Voice Service

Voice control|
Number of microphones| 3
Microphone array| Far field
Bluetooth

WiFi (standard); (encryption, WPS )

| Dual Band 2.4 GHz (b/g/n) & 5 GHz (a/c) MiMo 1×1 WiFi
Bluetooth (standard)| 4.1 Low Energy (BLE)
USB| Playback & update
Digital optical IN|
AUX-IN|
Line-Out|
Other details and speci fi cations

Remote control| Hama SRC-1805 Layout B
Batteries| 2x AAA
Option for wall hanging|
Size (W xHx D)| 36.5 cm x 21.5 cm x 17.5 cm
Weight| 5.0 kg
Equaliser / DSP

Pro fi les| 2 (Standard and My Equaliser)
Standards & decoders

Max. sound resolution (Hi-res)| 192 kHz / 24 bit
Hi-res audio codecs supported| FLAC, ALAC
Online update| Forced / manual update
Streaming

WiFi stream (DLNA compatible)|
UPnP|
Loudspeaker

2x mid-woofer| 4″ (10.16 cm)
2x tweeter| 20 mm
1x sub-woofer| 4″ (10.16 cm)
Ampli fi er class| Class D (TAS5754)

Operating Instructions

Thank you for choosing aHama product. Take your time and read the following instructions and information completely.Please keep these instructions in asafe place for futurereference. If you sell the device, please pass these operating instructions on to the new owner.

Explanation of warning symbols and notes

Risk of electric shock
This symbol indicates product parts energized with a dangerous voltage of sufficient magnitude to constitute arisk of electric shock.
Warning
This symbol is used to indicate safety instructions or to draw your attention to specifichazards and risks.
Note
This symbol is used to indicate additional information or important notes.

Package Contents

• “SIRIUM2000AMBT/SIRIUM2100AMBT” Hama Smart Speaker
• AC/DC Adapter
• SRC-1805 Layout BRemote Control
• 2xAAA Batteries
• Quick Reference Guide

Safety Notes

• The product is intended only for use inside buildings.
• The product is intended for private, non-commercial use only.
• Protect the product from dirt, moistureand overheating and us it in dry rooms only. As with all electrical devices, this device should be kept out of the reach of children.
• Do not drop the product and do not expose it to any major shocks.
• Do not operate the product outside the power limits given in the technical data.
• Keep the packaging material out of the reach of children due to the risk of suffocation.
• Dispose of packaging material immediately according to locally applicable regulations.
• Do not modify the device in any way.Doing so voids the warranty.

Risk of electric shock

• Do not open the device or continue to operate it if it becomes damaged.
• Do not use the product if the AC adapter,adapter cable or power cable is damaged.
• Do not attempt to service or repairthe product yourself.
  Leave any and all service work to qualified experts.

Warning -Batteries

• When inserting batteries, note the correct polarity (+ and -markings) and insert the batteries accordingly.
  Failuretodosocould result in the batteries leaking or exploding.

• Do not allow children to change batteries without supervision.

• Do not mix old and new batteries, or batteries of different types or from different manufacturers.

• Remove batteries from products that arenot going to be used for aprolonged period of time.

• Do not short-circuit batteries.

• Do not charge batteries.

• Do not burn batteries.

• Keep batteries out of the reach of children.

• Remove spent batteries from the product and dispose of them without delay.

Before commissioning

Preparing the remote control for use
Open the cover on the battery compartment. This can be found on the back of the remote control and can be opened by sliding in the direction indicated.
The extent of delivery includes two AAA batteries which must be inserted into the battery compartment for the remote control to work. When inserting the batteries, ensurethat they areinserted with the correct polarity.
The relevant polarity (+ /-)ismarked inside the battery compartment.

Getting started

Note
Use only original accessories (or: accessories approved by Hama) to avoid damage to the product.

Warning

• Only operate the product at asocket that has been approved for the device. The socket must be installed close to the product and must be easily accessible.
• Disconnect the product from the power supply using the On/Off switch –ifthis is not available, unplug the power cordfromthe socket.
• When using amulti-socket power strip, make sure that the sum power draw of all the connected devices does not exceed its maximum throughput rating.
• If you will not be using the product for along period of time, disconnect it from mains power.

Switching on

• Connect the mains lead on the loudspeaker to aproperly installed socket.
• The loudspeaker switches on automatically.

Note -switching on for the first time

• When first switched on, the loudspeaker is in “Device setup” mode and the status LEDs (1-5) pulse.
• If setup mode is not active, brieflypress the [SETUP] button (2) on the back of the device with apointed instrument (e.g. apaper clip) to activate WPS mode (flashes rapidly). Alternatively,press and hold the [SETUP] button (2) for around 7seconds to open an AccessPoint (flashes slowly).
• At the next switch-on, all of the status LEDs (1-5) flash orange until the connections made so far have been restored. Depending on the Internet signal strength, this may take up to 20 seconds.

Switching on /off /standby

• Press [POWER] (1) to switch on the loudspeaker.
  Alternatively,press [POWER] (1) on the remote control.

• Press [POWER] (1) again on the device or the remote control to switch the loudspeaker off.(Standby)

Note

• To switch the loudspeaker off completely,disconnect it from the power supply.

Volume adjustment /mute

• Press [VOLUME -/+] to reduce /increase the volume.
• Press on the remote control to mute the loudspeaker.
• Press again to reset the volume to the value it was prior to being muted.

Setting up the loudspeaker

Note

• To be able to use all of the product’s functions, the Amazon Alexa App must also be downloaded and an Amazon account set up. To do this, follow the instructions in the Amazon Alexa App. More information on this can be found at www.amazon.de.

6.1. Downloading the Hama Smart Audio App

****Note
The following operating systems aresupported:

• iOS 8orhigher
• Android 4.4.2 or higher
• Open the iTunes AppStoreorGoogle Play Storeonyour smartphone.
• Use the search term “Hama Smart Audio”.
• Download the App as normal and install it on your smartphone. To do this, follow the instructions on your smartphone.

6.2. Setting up the device for the first time with the Hama Smart Audio App (ALEXA function)

WLAN note (wireless network)

• Ensurethat the router is switched on, is functioning correctly and that thereisaconnection to the Internet /network.

• Activate the WLAN function of your router if it is not already activated.

• Followyour router´s operating instructions as regards the correct functioning of the WLAN connection.

• Ensurethat the loudspeaker is in WLAN pairing mode.
  The status LEDs (1-5) flash.

• If setup mode is not active, brieflypress the [SETUP] button (2) on the back of the device with apointed instrument (e.g. apaper clip) to activate WPS mode (flashes rapidly). Alternatively,press and hold the [SETUP] button (2) for around 7seconds to open an AccessPoint (flashes slowly).

• Ensurethat the Hama Smart Audio App is installed on your smartphone and that all updates have been installed.

• Open the Hama Smart Audio App and touch [Setup].

• Then touch [Add speaker].

• Open your smartphone’s WLAN settings by touching [WLAN settings].

• In your smartphone’s WLAN settings, search for the Hama SIRIUM2000AMBT/SIRIUM2100AMBT loudspeaker.
  Note

• The loudspeaker generates its own WLAN network bearing the name SIRIUMSetup and the first six digits of the MACaddress (e.g. SIRIUMSetup_E69EBB).
  This WLAN does not requireapassword.

• Connect your smartphone with the loudspeaker.

• Now return to the Hama Smart Audio App on your smartphone.

• Select the required WLAN name (SSID) with which you wish to connect the loudspeaker.

• Now also enter your network key if necessary and confirm with [Done].
  Note

• Often the Pre-Shared Keyisprinted on the back of the router /AP.

• When entering the key,take notice of capitalisation.

• Confirm the selected settings by touching [Confirm].

• The loudspeaker now connects to the network.
  After successful connection, “Loudspeaker configured successfully” appears on the smartphone. Note

• With iOS, the App may need to be closed and restarted. Then follow the two steps below.

• The sound bar that has been set up should now appear in the main menu. Press on the loudspeaker icon.

• Touch [Sources]atthe bottom edge of the screen to establish aconnection with your Amazon account.

• Then touch the [Amazon Alexa]button.

• Touch [SIGN IN WITH AMAZON] to open the web browser to enter your access details. Note

• If the Amazon Shopping App has already been installed and set up on your smartphone, the following steps areskipped.

• Using your smartphone’s keypad, enter the access details for your Amazon account and confirm your entries with Login.

• Alternatively,tap [Create new Amazon account] to create anew Amazon account.

• Following successful login, you willreturn to the Hama Smart Audio App.

• Now choose the language to which Alexa is to respond in future.

• Open the Amazon Alexa App and if necessary re-enter your access details. Youshould then find the loudspeaker in your active devices.

• Then adjust your personalised settings (time zone, device name, etc.) in the Amazon Alexa App. Further information on this can be found at www.amazon.com -> Help and Customer Service.
  Note

• Please note that location information for queries (e.g. “What is the weather going to be like”) will only work correctly if the correct location information has been entered into the Alexa App.

• Youcan now use Alexa as described in Section 12.

Initial Bluetooth®connection (pairing)

Youcan pair your devices with the loudspeaker using Bluetooth and use this as aplayback device for audio signals. Playback is controlled directly via the device or the remote control. The volume can also be controlled directly on the loudspeaker.

Note -Bluetooth®

• Check whether your mobile device (smartphone, tablet PC. etc.) is Bluetooth capable.
•  Note that the maximum range for Bluetooth ® is 10 metreswithoutobstaclessuchaswalls,people,etc.
• The connection may be disrupted by other Bluetooth ® devices/connections in the vicinity.
• The loudspeaker can only ever be paired with one device at atime.
• Note that compatibility depends on the supported Bluetooth ® profiles as well as the Bluetooth ® versions being used. (See: Technical data, operating manual of the device being used)
• Ensurethat your Bluetooth-enabled device is switched on and that Bluetooth is activated.
• Activate Bluetooth mode by repeatedly pressing the [SOURCE] button (2) on the loudspeaker.
• Alternatively,press Bluetoothonthe remote control.
• The Bluetooth status LED (4) starts to pulse blue.
• Press and hold the [SOURCE] button (2) for around 2seconds to activate pairing mode. The Bluetooth status LED (4) starts to flash blue and asignal tone sounds.
• Open the Bluetooth settings on your device and wait until the list of found Bluetooth devices shows Hama SIRIUM2000AMBT/SIRIUM2100AMBT.
• If necessary,start searching for Bluetooth devices on your device.
• Select the Hama SIRIUM2000AMBT/SIRIUM2100AMBT loudspeaker in the list of available devices and wait until the loudspeaker is shown as connected in your device’s Bluetooth settings.
• The Bluetooth status LED (4) now lights up solid blue.
• Start and control the audio playback accordingly via the device or remote control.

Note -Bluetooth ® password

Some devices requireapasswordinorder to connect to another Bluetooth ® device.

• If your device requests apasswordtoconnect to the loudspeaker,enter 0000.

7.1 Automatic Bluetooth® connection (after successful pairing)

• Devices that have already been paired with the loudspeaker arestored automatically on the loudspeaker.

Note -connection impaired
After the loudspeaker and device have been paired, aconnection is established automatically.Ifthe Bluetooth ® connection is not established automaticallycheck the following:

• Check the Bluetooth ® settings of your device to see whether SIRIUM2000AMBT/SIRIUM2100AMBT is connected. If not, repeat the steps listed under Bluetooth ® pairing.
• Check that your device and the loudspeaker are less than 10 metres apart. If not, move them closer together.
• Check whether obstacles areimpairing the range.
  If so, move the devices closer together.

7.2 Terminating the Bluetooth® connection

• Change to adifferent mode to terminate the Bluetooth ® connection between the loudspeaker and the device.
• Alternatively,you can terminate the connection manually on your device.

Connection via Auxiliary In /Auxiliary Out

Youcan connect mobile devices (such as smartphones, tablet PCs, MP3 players, etc.) and older analogue sources (CD/DVD player,etc.) to the loudspeaker via the analogue audio input and play their audio signal via the loudspeaker.
Here, you have the option to connect via a3.5 mm audio cable (jack cable).
Further loudspeakers can be connected via the analogue audio output (5), via which the audio signal is also played.

Note

• Switch the loudspeaker off beforeconnecting adevice to it.
• Do not bend or crush the cable.
• Forplayback via the AUX-In socket, connect your device via the AUX-In socket (4) using a3.5 mm audio cable (jack cable) to the loudspeaker and select AUX mode.
• Forplayback via the AUX-Out socket, connect further loudspeakers /anamplifier,for example, via the AUX-Out socket (5) using a3.5 mm audio cable (jack cable) to the loudspeaker and select AUX mode.
• Press [POWER] (1) to switch on the loudspeaker.
• Activate AUX mode by repeatedly pressing the [SOURCE] button (2) on the loudspeaker.
• The status LED (4) lights up cyan when AUX mode has been selected.
• Start and control audio playback accordingly via the connected device.
• Alternatively,press [LINE IN] (14) on the remote control.

Connection via Optical-IN

The loudspeaker’s digitalaudio input allowsyou to connect your device (e.g. TV) and play its audio signal via the loudspeaker.

Note

• Switch the loudspeaker off beforeconnecting adevice to it.
• Beforeconnection, remove the safety caps from both ends of the optical signal cable.
• Do not bend or crush the cable.
• Forplayback via the optical audio connection, connect an optical signal cable to the optical audio input on the loudspeaker and to the optical audio output on your device, and then select Optical mode.
• Press and hold [POWER] (1) for approximately 3seconds to switch on the loudspeaker.
• Activate Optical mode by repeatedly pressing the [SOURCE] button (2) on the loudspeaker.
• The Optical status LED (4) lights up purple when Optical ode is active.
• Alternatively,press [OpticalIN] (12) on theremotecontrol.

Network streaming

The loudspeaker allows audio files stored on aPC, tablet or smartphone to be played.

Note

• Please note that, depending on the source device you areusing, other softwarethat allows streaming may be required.

10.1 Playback from acomputer (streaming)
Youcan manage the loudspeaker via your computer and stream music to it from your computer.
Requirements:

• The loudspeaker and computer must be on the same network.
• The loudspeaker must have been authorised as aplayback device on the computer.

Proceed as follows: Control Panel -> Network and Internet -> Show network computers and devices The loudspeaker should now be listed here.

• Right-click on the icon or designation of the loudspeaker and choose Allow streaming to this device.
• Right-click again on the icon or designation of the loudspeaker and choose Show device website to change the friendly name of the device.
• Anew browser window opens. Youcan make the desired changes here.

Use:

• The loudspeaker can now access the PC’s shared directories and you can send audio data to the device for playback (streaming).
• The music directory of your music library is enabled as standard.
• Create and manage shared folders using Explorer or Windows Media Player.
• Right-click on the desired music file, choose Play To, and then select the loudspeaker’s friendly name.
• The loudspeaker begins to play the music file.

10.2 Playback via the network

To access one of the existing network shared files directly from the loudspeaker,proceed as follows:

• Open the Hama Smart Audio App and select the required loudspeaker.
• This takes you to the playback screen and the associated source selection in the footer.
• Touch [Sources] and then [Network devices /Playback sources].
• All of the shared files which the loudspeaker can access now appear.
• Select the relevant directory and required track. If there aremultiple files in one directory,these areplayed in sequence.

10.3 Playback from atablet /smartphone

To access one of the existing network shared files directly from the loudspeaker,proceed as follows:

• Open the Hama Smart Audio App and select the required loudspeaker.
• This takes you to the playback screen and the associated source selection in the footer.
• Touch [Sources] and then [Local content]. The memory in your smartphone /tablet is automatically searched and tracks found aregrouped by category (Albums, Artists, Country,Folder).
  Select acategory and the required track.

Alexa function (voice control)

• After saying the activation word(“Alexa”) or pressing the [Action]button (4), the status LED lights up blue and asignal tone sounds. Youcan now talktoAlexa.
• While Alexa is answering, the status LED flashes blue.

Note

• If the Amazon Market App has already been installed and set up on your smartphone, some smartphones will take the user data directly from the App.
• To set up anew Amazon account, log out and repeat the steps described in this section.

Note -Alexa Push to Talk /function key

• Brieflypress the [Action] button (4) on the loudspeaker to activate Alexa during audio mode or higher volume. Alternatively,press the [Action] button (3) on the remote control.
• Press the [Microphone Mute] button (3) to switch the microphone off.Ifthe microphones aredeactivated, the status LEDs (1-5) light up solid red. Alternatively, press the [Microphone Mute] button (4) on the remote control
• The loudspeaker will now no longer respond to the activation worduntil the microphones arereactivated.
• Press the [Microphone Mute] button (3) again to reactivate the microphone. Alternatively,press the [Microphone Mute] button (4) on the remote control.
  The status LEDs (1-5) go out.

Equaliser profiles

The equaliser allows you to adjust the sound of the loudspeaker to your preferences by altering the bass intensity.
Youcan choose from apreconfigured profile or create your own custom profile.

• Press [EQ1] (9) on the remote control to call up the pre-configured profile.
  To create acustom profile, proceed as follows:

• Press [EQ2] (11) on the remote control to start the configuration process.

• Change the bass intensity (5/6) on the remote control.
  If playback is already started when you modify these settings, you can hear the changes in the audio immediately.

• Confirm your settings by pressing [EQ2] again.
  Configuration can also be carried out via the App.

Bass control

• Press BASS +/- on the remote control to increase or reduce the loudspeaker’s bass.

Wireless network connection (WLAN)

Depending on the network, thereare anumber of ways to connect to it.
PBC setup

• Press the [SETUP]button (2).
• The status LED flashes quickly green.
• Press the WPS button on your router or current access point. This can often be done using the web interface, as well.
• Consult the operating instructions of your router /AP for details of the exact procedure.
• Once the procedurehas also been initiated on the router /AP, the loudspeaker should connect with the access and the network connection should be available.

Note

• Press the [SETUP]button (2) to abort PBC setup.

Open network

Note

• We recommend against establishing unsecured connections and advise you to always protect your network against unauthorised access.
• If the network you plan to use does not have any security features, simply select the network from the list and confirm it. The radio then connects immediately to the network.

Establishing aconnection with another home network

• Press and hold the [SETUP]button (2) for around 7seconds. The status LED flashes rapidly.
• The loudspeaker can now be connected to another network.

Factory reset

To reset the loudspeaker to the factory default settings (delivery condition), proceed as follows:

• Press and hold the [SETUP] (2) and [Action] (4) buttons for around 6seconds to reset the loudspeaker to the factory default settings.

• Once the loudspeaker has been reset, it restarts.
  Note

• Resetting to the factory default settings can solve some problems and malfunctions.

• However,all settings made previously,such as equaliser presets, favourites and network profiles, arepermanently deleted.

Software update

• We areconstantly developing new softwarefeatures and improvements for our loudspeaker to fixpotential problems, add functionality,etc.
• We recommend that you always install updates to your loudspeaker.
• Update notifications will be provided in the Hama Smart Audio App.
• During the update, the Update status LED (2) lights up solid.

Warning

• Make surethat the radio has astable power supply beforeyou start asoftwareupdate.
• Power supply failureduring asoftwareupdate can cause irreparable damage to the loudspeaker.

Wall mounting

Note

• Ensurethat the mount you have chosen can carry aload of at least 5kg.
• Follow the directions and safety notes included with the mounting bracket.
• With the correct mount, it is possible to attach the loudspeaker to the wall.
• To do this, use the mounting holes (1) on the back of the loudspeaker.

Care and Maintenance

• Only clean this product with aslightly damp, lint-free cloth and do not use aggressive cleaning agents.
• If you do not use the product for along time, turn off the device and disconnect it from the power supply.Storeit in aclean, dry place out of direct sunlight.

Warranty Disclaimer

Hama GmbH &CoKGassumes no liability and provides no warranty for damage resulting from improper installation/ mounting, improper use of the product or from failureto observe the operating instructions and /orsafety notes.

21. Declaration of Conformity
****Hama GmbH &CoKGhereby declares that the radio equipment type [00054881, 00054882, 00054886, 00054887] is in compliance with Directive 2014/53/EU.The full text of the EU declaration of conformity is available at the following internet address: www.hama.com -> 00054881, 00054882, 00054886, 00054887 -> Downloads.

Frequency band(s)| Bluetooth:2.402 GHz -2.480 GHz
WiFi: 2.402 GHz –2.480 GHz
WiFi: 2.412 GHz –2.483 GHz
WiFi: 5.150 GHz –5.350 GHz
WiFi: 5.470 GHz –5.725 GHz
---|---
Maximum radiofrequency
power transmitted| Bluetooth: 4dBm (EIRP)
WiFi: 2.4 GHz /19.5 dBm (EIRP)
WiFi: 5GHz /16.5 dBm (EIRP)

Limitations or requirements in
Belgium, Bulgaria, Czech Republic, Denmark, Germany, Estonia, Ireland, Greece, Spain, France, Croatia, Italy, Cyprus, Latvia, Lithuania, Luxembourg, Hungary,Malta, the Netherlands, Austria, Poland, Portugal, Romania, Slovenia, Slovakia, Finland, Sweden, United Kingdom
Note
If channels 36–64 (channels of frequency 5150 – 5350 MHz) areused, the product may only be used in closed rooms.

Service &Support
www.hama.com
+49 9091 502-115
www.hama.com/nep

The Spotify softwareissubject to thirdparty licenses found here: www.spotify.com/connect/third-party-licenses

The Bluetooth ® wordmark and logos areregisteredtrademarks owned by Bluetooth SIG, Inc. and any use of such marks by Hama GmbH &CoKGisunder license. Other trademarks and trade names arethose of their respective owners.
Alllistedbrands are trademarks of thecorrespondingcompanies.Errorsand omissionsexcepted, andsubjecttotechnicalchanges.Our general termsofdeliveryand payment are applied.

00054881_86/0 0054882_87/12.18

References

• . Spend less. Smile more.
• Amazon.de: Low Prices in Electronics, Books, Sports Equipment & more
• hama.com
• hama.com
• Recycling Information hama.com
• Third Party Licenses | Spotify for Developers

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>