infinity LEARINR567 Series Raccoon P14 4 Professional RGBM Par User Manual

June 13, 2024
Infinity

infinity LEARINR567 Series Raccoon P14 4 Professional RGBM Par

infinity-LEARINR567-Series-Raccoon-P14 4-Professional-RGBM-
Par

Product Information

Product Name Raccoon P14/4
Product Code 200500
Version V1

Product Usage Instructions

Before Using the Product

Important: Read and follow the instructions in this user manual before installing, operating, or servicing this product.
The manufacturer will not accept liability for any resulting damages caused by the non-observance of this manual.
After unpacking, check the contents of the box. If any parts are missing or damaged, contact your Highlite International dealer.

USER MANUAL

ENGLISH

Raccoon P14/4

V1
Product code: 200500

Highlite International B.V. ­ Vestastraat 2 ­ 6468 EX ­ Kerkrade ­ the Netherlands

Raccoon P14/4

Preface

Thank you for purchasing this Infinity product.
The purpose of this user manual is to provide instructions for the correct and safe use of this product.
Keep the user manual for future reference as it is an integral part of the product. The user manual shall be stored at an easily accessible location.
This user manual contains information concerning:
Safety instructions Intended and non-intended use of the device Installation and operation of the device Maintenance procedures Troubleshooting Transport, storage and disposal of the device
Non-observance of the instructions in this user manual may result in serious injuries and damage of property.

©2022 Infinity. All rights reserved.
No part of this document may be copied, published or otherwise reproduced without the prior written consent of Highlite International.
Design and product specifications are subject to change without prior notice.
For the latest version of this document or other language versions, please visit our website www.highlite.com or contact us at service@highlite.com.
Highlite International and its authorized service providers are not liable for any injury, damage, direct or indirect loss, consequential or economic loss or any other loss arising from the use of, or inability to use or reliance on the information contained in this document.

Product code: 200500

Product code: 200500

3

Raccoon P14/4

Introduction

Before Using the Product
Important Read and follow the instructions in this user manual before installing, operating or servicing this product.
The manufacturer will not accept liability for any resulting damages caused by the non-observance of this manual.
After unpacking, check the contents of the box. If any parts are missing or damaged, contact your Highlite International dealer.
Your shipment includes: Infinity Raccoon P14/4 Seetronic Schuko to Power Pro True power cable (1,5 m) Quick-lock bracket User manual

Fig. 01

Intended Use

This device is intended for professional use as an outdoor LED par effect. This device is not suitable for households and for general lighting.

Any other use, not mentioned under intended use, is regarded as non-intended and incorrect use.

Product Lifespan

This device is not designed for permanent operation. Disconnect the device from the electrical power supply when the device is not in operation. This will reduce the wear and will improve the device’s lifespan.

LEDs Lifespan

The light output of the LEDs gradually decreases over time (lumen depreciation). High operating temperatures contribute to this process. You can extend the lifespan of the LEDs by providing adequate ventilation and operating the LEDs at the lowest possible brightness.

Text Conventions

Throughout the user manual the following text conventions are used:

Buttons: References:
0­255: Notes:

All buttons are in bold lettering, for example “Press the UP/DOWN buttons” References to chapters and parts of the device are in bold lettering, for example: “Refer to 2. Safety”, “turn the adjustment handle (05)” Defines a range of values Note: (in bold lettering) is followed by useful information or tips

Product code: 200500

4

Raccoon P14/4

Symbols and Signal Words

Safety notes and warnings are indicated throughout the user manual by safety signs. Always follow the instructions provided in this user manual.

DANGER

Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.

WARNING

Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.

CAUTION

Indicates a potentially hazardous situation, which, if not avoided, may result in minor or moderate injury.

Attention

Indicates important information for the correct operation and use of the product.

Important Read and observe the instructions in this document.

Electrical hazard

Provides important information about the disposal of this product.

Symbols on the Information Label
This product is provided with an information label. The information label is located on the mounting bracket. The information label contains the following symbols:
This device falls under IEC protection class I.

This device shall not be treated as household waste.
Read and follow the instructions in the user manual before installing, operating or servicing the device. This device is rated IP65.

Product code: 200500

5

Raccoon P14/4

Safety

Important Read and follow the instructions in this user manual before installing, operating or servicing this product.
The manufacturer will not accept liability for any resulting damages caused by the non-observance of this manual.
Warnings and Safety Instructions
DANGER Danger for children
For adult use only. The device must be installed beyond the reach of children.
Do not leave various parts of the packaging (plastic bags, polystyrene foam, nails, etc.) within children’s reach. Packaging material is a potential source of danger for children.
DANGER Electric shock caused by dangerous voltage inside
There are areas within the device where dangerous touch voltage (> 120 V DC) may be present.
Do not open the device or remove any covers. Do not operate the device if the covers or the housing are open. Before operation, check if the
housing is firmly closed and all screws are tightly fastened. Disconnect the device from electrical power supply before service and maintenance, and when the
device is not in use.
DANGER Electric shock caused by short-circuit
This device falls under IEC protection class I.
Make sure that the device is electrically connected to ground (earth). Connect the device only to a socket-outlet with ground (earth) connection.
Do not cover the ground (earth) connection. Do not bypass the thermostatic switch or fuses. Do not let the power cable come into contact with other cables. Handle the power cable and all
connections with the mains with caution. Do not modify, bend, mechanically strain, put pressure on, pull or heat up the power cable. Make sure that the power cable is not crimped or damaged. Examine the power cable periodically
for any defects. Do not immerse the device in water or other liquids. Do not install the device in a location where
flooding may occur. Do not use the device during thunderstorms. Disconnect the device from the electrical power supply
immediately. Keep the connectors sealed with the rubber caps when the connectors are not in use. Do not connect the cables from above the connectors, if the device is installed outdoors. Make a
`drip loop’ in the cable so that rain water cannot enter the device.

Product code: 200500

6

Raccoon P14/4
WARNING Risk of epileptic shock
Strobe lighting can trigger seizures in photosensitive epilepsy. Sensitive persons should avoid looking at strobe lights.
Attention Power supply
Before connecting the device to the power supply, make sure that the current, voltage and frequency match the input voltage, current and frequency specified on the information label on the device.
Make sure that the cross-sectional area of the extension cords and power cables is sufficient for the required power consumption of the device.
Attention General safety
Do not connect the device to a dimmer pack. Do not switch the device on and off in short intervals. This decreases the device’s life. Do not shake the device. Avoid brute force when installing or operating the device. Change the lens or the LEDs if they are visibly damaged to such an extent that their effectiveness is
impaired, for example by cracks or deep scratches. Contact your Highlite International dealer for more information, as servicing can be performed only by instructed or skilled persons. If the device is dropped or struck, disconnect the device from the electrical power supply immediately. If the device is exposed to extreme temperature variations (e.g. after transportation), do not switch it on immediately. Let the device reach room temperature before switching it on, otherwise it may be damaged by the formed condensation. If the device fails to work properly, discontinue the use immediately.
Attention For professional use only This device shall be used only for the purposes it is designed for.
This device is intended for professional use as an outdoor LED par effect. Any incorrect use may lead to hazardous situations and result in injuries and material damage.
This device is not suitable for households and for general lighting. This device is not designed for permanent operation. This device does not contain user-serviceable parts. Unauthorized modifications to the device will
render the warranty void. Such modifications may result in injuries and material damage.

Product code: 200500

7

Raccoon P14/4
Attention Before each use, examine the device visually for any defects.
Make sure that:
All screws used for installing the device or parts of the device are tightly fastened and are not corroded.
The safety devices are not damaged. There are no deformations on housings, fixations and installation points. The lens is not cracked or damaged. The power cables are not damaged and do not show any material fatigue.
Attention Do not expose the device to conditions that exceed the rated IP class conditions.
This device is IP65 rated. IP (Ingress Protection) 65 class means that the device is dust-tight and protected against harmful effect of water jets.
Keep the connectors sealed with the rubber caps when the connectors are not in use.
Requirements for the User
This product may be used by ordinary persons. Maintenance may be carried by ordinary persons. Installation and service shall be carried out only by instructed or skilled persons. Contact your Highlite dealer for more information.
Instructed persons have been instructed and trained by a skilled person, or are supervised by a skilled person, for specific tasks and work activities associated with the installation, service and maintenance of this product, so that they can identify risks and take precautions to avoid them.
Skilled persons have training or experience, which enables them to recognize risks and to avoid hazards associated with the installation, service and maintenance of this product.
Ordinary persons are all persons other than instructed persons and skilled persons. Ordinary persons include not only users of the product but also any other persons that may have access to the device or who may be in the vicinity of the device.

Product code: 200500

8

Raccoon P14/4
3. Description of the Device
The Infinity Raccoon P14/4 is an IP65-rated LED par effect. It is equipped with 14 extremely bright LEDs (red, green, blue, mint). It is suitable for rental applications and situations that demand a high light output.
Front View

  1. Mounting bracket 02) 2 x adjustment screws 03) 14 x 15 W RGBM LEDs

Back View

Fig. 02
04) Safety eye 05) IP65-rated Seetronic 5-pin DMX signal
connector IN 06) IP65-rated Seetronic power connector IN 07) Protective vent 08) OLED display + control buttons 09) IP65-rated Seetronic power connector OUT 10) IP65-rated Seetronic 5-pin DMX signal
connector OUT

Product code: 200500

Fig. 03 9

Raccoon P14/4

Product Specifications

Model:

Raccoon P14/4

Electrical: Input voltage: Power consumption:

100­240 V AC, 50/60 Hz 165 W

Physical: Dimensions: Weight:

300 x 260 x 195 mm (L x W x H) 5,5 kg

Optics: Light source: Dimmer: Strobe: Lumen total: CRI: CCT: Refresh rate: Beam angle (circular):

14 x 15 W RGBM LEDs 0­100 % 0­20 Hz 8000 lm 87 2700­8000 K 640­25000 Hz 10°

Operation and control: Control: DMX channels:
Control panel:

Stand-alone (Manual, Built-in effects) DMX-512, RDM Dimmer (1 channel) Pixel (3 channels) Basic (8 channels) XY (8 channels) Raw (8 channels) HSI (10 channels) RGB (12 channels) CMY (12 channels) OLED display and buttons

Connections: Power connections: Data connections: Signal pinouts:

IP65-rated Seetronic Power Pro connectors IN/OUT IP65-rated Seetronic 5-pin DMX connectors IN/OUT Pin 1 (ground), pin 2 (-), pin 3 (+), pin 4 (N/C), pin 5 (N/C)

Construction: Housing: Color: IP rating: Cooling:

Die-cast aluminum Black IP65 Convection

Thermal: Maximum ambient temperature ta: Minimum ambient temperature:

45 °C -5 °C

Minimum distance: Minimum distance from flammable surfaces: Minimum distance to lighted object:

0,5 m 0,5 m

Product code: 200500

10

Raccoon P14/4
Optional Accessories
You can additionally purchase the following accessories:
Product code: 200560 (Accessory Holder for Raccoon Series) Product code: 200251 (Barndoor for 300W Fresnel) Product code: 200561 (Top Hat for Raccoon Series) Product code: 200564 (15° Diffusor for Raccoon Series) Product code: 200565 (20° Diffusor for Raccoon Series) Product code: 200566 (40° Diffusor for Raccoon Series) Product code: 200567 (90° Diffusor for Raccoon Series) Product code: 200568 (15° x 60° Diffusor for Raccoon Series)
Dimensions

Fig. 04

Installation

Safety Instructions for Installation

WARNING Incorrect installation can cause serious injuries and damage of property.

If trussing systems are used, installation must be carried out only by instructed or skilled persons.
Follow all applicable European, national and local safety regulations concerning rigging and trussing.
Personal Protective Equipment
During installation and rigging wear personal protective equipment in compliance with the national and site-specific regulations.
Installation Site Requirements
The device can be used outdoors. The device can be mounted to a truss or other rigging structure in any orientation. The minimum distance between the light output and the illuminated surface must be bigger
than 0,5 m. The maximum ambient temperature ta = 45 °C must never be exceeded.

Product code: 200500

11

Raccoon P14/4
Rigging
The device can be mounted to a truss or other rigging structure in any orientation. Make sure that all loads are within the pre-determined limits of the supporting structure.
CAUTION Restrict the access under the work area during rigging and/or derigging.
To mount the device, follow the steps below: Fasten the quick-lock bracket (Fig. 05). Install the clamp, as shown in Fig. 05. Make sure that the clamp is suitable for attaching of the device to a truss.

Fig. 05
Attach the device to the supporting structure. Make sure that the device cannot move freely. Secure the device with a secondary suspension, for example a safety cable. Make sure that the secondary suspension can hold 10 times the weight of the device. If possible, the secondary suspension should be attached to a supporting structure independent of the primary suspension. Put the safety cable through the safety eye (04), as shown in Fig. 05.

Product code: 200500

12

Raccoon P14/4

Angle Adjustment
You can adjust the angle of the device with the 2 adjustment screws (02).
Turn the 2 adjustment screws (02) counterclockwise to loosen them. 02) Tilt the device to the desired angle (Fig. 06). 03) Turn the 2 adjustment screws (02) clockwise to tighten them. Make sure that the device cannot
move freely after the 2 adjustment screws (02) are tightened.

Fig. 06
Accessory Holder Installation
You need to install the Accessory Holder on the device before you install the other accessories.
The Accessory Holder is not supplied and shall be purchased separately. See 3.4. Optional Accessories on page 11. Contact your Highlite International dealer for more information.
To install the Accessory Holder, follow the steps below:
Put the Accessory Holder on the lens of the Raccoon (Fig. 07). 02) Use a screwdriver to tighten the 4 screws (supplied with the Accessory Holder) to secure the
Accessory Holder in position (Fig. 08).

Product code: 200500

Fig. 07 13

Fig. 08

Raccoon P14/4

Barndoor Installation
The Barndoor is not supplied and shall be purchased separately. See 3.4. Optional Accessories on page 11. Contact your Highlite International dealer for more information.
To install the Barndoor, follow the steps below:
Install the Accessory Holder. See 4.6. Accessory Holder Installation on page 13 for more information. 02) Lift the spring-loaded retainer clip of the Accessory Holder and flip it backwards (Fig. 09). 03) Insert the Barndoor into the Accessory Holder (Fig. 10). 04) Pull the spring-loaded retainer clip of the Accessory Holder downwards (Fig. 11). The Barndoor will be
locked in position. 05) Secure the Barndoor to the overhead structure with a secondary attachment, for example a safety
cable.

Fig. 09

Fig. 10

Fig. 11

Product code: 200500

14

Raccoon P14/4

Top Hat Installation
The Top Hat is not supplied and shall be purchased separately. See 3.4. Optional Accessories on page 11. Contact your Highlite International dealer for more information.
To install the Top Hat, follow the steps below:
Install the Accessory Holder. See 4.6. Accessory Holder Installation on page 13 for more information. 02) Lift the spring-loaded retainer clip of the Accessory Holder and flip it backwards (Fig. 12). 03) Insert the Top Hat into the Accessory Holder (Fig. 13). 04) Pull the spring-loaded retainer clip of the Accessory Holder downwards (Fig. 14). The Top Hat will be
locked in position. 05) Secure the Top Hat to the overhead structure with a secondary attachment, for example a safety
cable.

Fig. 12

Fig. 13

Fig. 14

Product code: 200500

15

Raccoon P14/4
Diffusor Installation
The Diffusor is not supplied and shall be purchased separately. See 3.4. Optional Accessories on page 11. Contact your Highlite International de aler for more information.
To install the Diffusor, follow the steps below:
Install the Accessory Holder. See 4.6. Accessory Holder Installation on page 13 for more information. This step is optional. It is possible to install the Diffusor with or without the Accessory Holder. 02) Put the Diffusor on the lens of the device or on the Accessory Holder (if installed) as shown in Fig. 15. The magnets in the Diffusor will keep it in position. 03) Secure the Diffusor to the overhead structure with the safety cable of the Diffusor.

Connecting to Power Supply

Fig. 15

DANGER Electric shock caused by short-circuit

The device accepts AC mains power at 100­240 V and 50/60 Hz. Do not supply power at any other voltage or frequency to the device.
This device falls under IEC protection class I. Make sure that the device is always electrically connected to the ground (earth).
Before connecting the device to the socket-outlet: Make sure that the power supply matches the input voltage specified on the information label on
the device. Make sure that the socket-outlet has ground (earth) connection.
Connect the device to the socket-outlet with the power plug. Do not connect the device to a dimmer circuit, as this may damage the device.
This device is IP65 rated.
Do not expose the device to conditions that exceed the rated IP class conditions. Keep the connectors sealed with the rubber caps when the connectors are not in use. Do not connect the cables from above the connectors, if the device is installed outdoors. Make a
`drip loop’ in the cable so that rain water cannot enter the device. Make sure that the cable run is not too heavy. A heavy cable run can cause damage to the
connectors. If the connectors are damaged, their ingress protection (IP) can deteriorate.

Product code: 200500

16

Raccoon P14/4
Power Linking of Multiple Devices
This device supports power linking. Power can be relayed to another device via the power OUT connector. Note that the input and the output connectors have different designs: one type cannot be connected to the other.
Power linking of multiple devices must be carried out only by instructed or skilled persons.
WARNING Incorrect power linking may lead to overload of the electrical circuit and result in serious injuries and damage of property.
To prevent overload of the electrical circuit, when power linking multiple devices:
Use cables with sufficient current-carrying capacity. The power cable supplied with the device is not suitable for power linking of multiple devices.
Make sure that the total current draw of the device and all connected devices does not exceed the rated capacity of the power cables and the circuit breaker.
Do not link more devices on one power link than the maximum recommended number. Maximum recommended number of devices: at 100­120 V: 3 devices at 200­240 V: 6 devices
5. Setup
Warnings and Precautions
DANGER Electric shock caused by short-circuit
This device is IP65 rated.
Do not expose the device to conditions that exceed the rated IP class conditions. Keep the connectors sealed with the rubber caps when the connectors are not in use. Do not connect the cables from above the connectors, if the device is installed outdoors. Make a
`drip loop’ in the cable so that rain water cannot enter the device. Make sure that the cable run is not too heavy. A heavy cable run can cause damage to the
connectors. If the connectors are damaged, their ingress protection (IP) can deteriorate.
Attention Connect all data cables before supplying power. Disconnect power supply before connecting or disconnecting data cables.
Stand-alone Setup
When the Raccoon P14/4 is not connected to a controller or to other devices, it functions as a standalone device.
For more information about the control modes, refer to 6.2. Control Modes on page 20.

Product code: 200500

17

Raccoon P14/4

DMX Connection

DMX-512 Protocol
You need a DMX serial data link to run light shows of one or more devices using a DMX-512 controller.
The Raccoon P14/4 has 5-pin DMX signal IN and OUT connectors.
The pin assignment is as follows: 5-pin: pin 1 (ground), pin 2 (-), pin 3 (+), pin 4 (N/C), pin 5 (N/C)
Devices on a serial data link must be daisy-chained in a single line. The number of devices that you can control on one data link is limited by the combined number of the DMX channels of the connected devices and the 512 channels available in one DMX universe.
To comply with the TIA-485 standard, no more than 32 devices should be connected on one data link. In order to connect more than 32 devices on one data link, you must use a DMX optically isolated splitter/booster, otherwise this may result in deterioration of the DMX signal.
Note: Maximum recommended DMX data link distance: 300 m Maximum recommended number of devices on a DMX data link: 32 devices

DMX Cables
Shielded twisted-pair cables with 5-pin XLR connectors must be used for reliable DMX connection. You can purchase DMX cables directly from your Highlite International dealer or make your own cables.
If you use XLR audio cables for DMX data transmission, this may lead to signal degradation and unreliable operation of the DMX network.
When you make your own DMX cables, make sure that you connect the pins and wires correctly as shown in Fig. 16.

Product code: 200500

18

Fig. 16

Raccoon P14/4
DMX Linking
To connect multiple devices on one DMX data link, follow the steps below:
Use a 5-pin DMX cable to connect the DMX OUT connector of the lighting controller to the DMX IN connector of the first device. 02) Connect the first device’s DMX OUT connector to the second device’s DMX IN connector with a 5-pin DMX cable. 03) Repeat step 2 to connect all devices in a daisy-chain as shown in Fig. 17. 04) Connect a DMX terminator (120 resistor) to the DMX OUT connector of the last device on the data link.

Fig. 17
DMX Addressing
In a setup with multiple devices, make sure that you set the DMX starting address of each device correctly. The Raccoon P14/4 has 8 personalities: Dimmer (1 channel), Pixel (3 channels), Basic (8 channels), XY (8 channels), Raw (8 channels), HSI (10 channels), RGB (12 channels), CMY (12 channels).
If you want to connect multiple devices on one data link and use them in 12-channel mode (RGB or CMY), follow the steps below:
Set the starting address of the 1st device on the data link to 1 (001). 02) Set the starting address of the 2nd device on the data link to 13 (013), as 1

  • 12 = 13. 03) Set the starting address of the 3rd device on the data link to 25 (025) as 13 + 12 = 25. 04) Continue assigning the starting addresses of the remaining devices by adding each time 12 to the
    previous number.
    Make sure that you do not have any overlapping channels in order to control each Raccoon P14/4 correctly. If two or more devices are addressed similarly, they will work similarly.

Product code: 200500

19

Raccoon P14/4

Operation

Safety Instructions for Operation
Attention This device must be used only for the purposes it is designed for.
This device is intended for professional use as an outdoor LED par effect. This device is not suitable for households and for general lighting. Any other use, not mentioned under intended use, is regarded as non-intended and incorrect use.
Attention Power supply
Before connecting the device to the power supply, make sure that the current, voltage and frequency match the input voltage, current and frequency specified on the information label on the device.

Control Modes

The Raccoon P14/4 can be operated with a DMX controller and as a stand-alone device. The Raccoon P14/4 supports the following control modes: Stand-alone: Manual, Built-in effects DMX-512, RDM: 1, 3, 8, 8, 8, 10, 12, 12 channels For more information about how to connect the devices, refer to 5. Setup on pages 17­19. To operate the device manually as a stand-alone device, adjust the intensity values for the colors. See 6.6.3.1. Static Colors on page 27 for more information. To run one of the built-in effects, adjust the dimmer intensity, the fade times and the duration of the effects. See 6.6.3.2. Built- in Effects on page 28 for more information. To operate the device with a DMX controller: 01) Set the DMX starting address of the device in the Address menu. See 5.3.4. DMX Addressing on page
19 and 6.6.2. DMX Address on page 26. 02) Select the behavior of the device in case there is no DMX signal in the DMX Lost menu. See 6.6.12.
DMX Failure on page 32. 03) Select the DMX channel mode. See 6.6.1. DMX Channel Mode on page 26 for more information. See
6.7. DMX Channels on page 35 for complete overview of all DMX channels.

Product code: 200500

20

Raccoon P14/4 Control Panel

A) OLED display B) DOWN button C) UP button D) SET button E) MODE button

Fig. 18
Use the MODE button to exit the current submenu and to return to the Main Menu. Use the UP/DOWN buttons to navigate through the menus or to increase/decrease numeric values. Use the SET button to open menus, to confirm choices or to adjust values.
Start-up
Upon start-up, the display shows a splash screen with the Infinity logo and the name of the device.

Immediately afterwards, the display shows the current operation mode, the frequency and the temperature of the LEDs.

Press the MODE button to enter the main menu.
Note:
If no button is pressed after 20 seconds of inactivity, the display will turn off. Press any button to return to the main menu. See 6.6.11.1. Backlight on page 31 for more information.
If the display is locked, you need to enter a password to access the main menu. Press the buttons in the following order: UP, DOWN, UP, DOWN to unlock the display. See 6.6.11.3. Key Lock on page 32 for more information.

Product code: 200500

21

Raccoon P14/4 Menu Overview

Product code: 200500

22

Raccoon P14/4

Product code: 200500

23

Raccoon P14/4

Product code: 200500

24

Raccoon P14/4
Main Menu Options
The main menu has the following options:

DMX Mode:

See 6.6.1. DMX Channel Mode

DMX Address: See 6.6.2. DMX Address

Manual:

See 6.6.3. Manual Mode

Dimmer Curve: See 6.6.4. Dimmer Curve Selection

Dimmer Speed: See 6.6.5. Dimmer Speed

Color Space: See 6.6.6. Color Space Selection

Tungsten:

See 6.6.7. Tungsten Mode

LED Mode:

See 6.6.8. LED Mode

Calibration:

See 6.6.9. Calibration

LED Frequency: See 6.6.10. LED Frequency

Display:

See 6.6.11. Display Settings

DMX Lost:

See 6.6.12. DMX Failure

Information:

See 6.6.13. System Information

Product code: 200500

25

Raccoon P14/4
Send Settings: See 6.6.14. Sending Settings Factory Settings: See 6.6.15. Restoring Factory Settings Press the UP/DOWN buttons to select menus. Press the SET button to open menus.
DMX Channel Mode In this menu you can select the DMX channel mode. 01) Press the UP/DOWN buttons to select the desired DMX channel mode. There are 8 options available:

DIMMER (1-channel mode) PIXEL (3-channel mode) BASIC (8-channel mode) XY (8-channel mode) RGB (12-channel mode) CMY (12-channel mode) HSI (10-channel mode) RAW (8-channel mode) 02) Press the SET button to confirm.
DMX Address In this menu you can set the DMX starting address of the device.

  1. Press the UP/DOWN buttons to select the starting DMX address of the device. The selection range is
    between 1 and 512.
  2. Press the SET button to confirm. Note: The display shows the DMX address range currently used by the device. For example, “4­6” means that the starting address of the device is 004 and that the device is operating in the 3-channel mode (DMX channels: 004, 005 and 006).

Product code: 200500

26

Raccoon P14/4
Manual Mode In this menu you can use the device in Static Color mode or activate one of the 3 built-in effects. 01) Press the UP/DOWN buttons to select one of the 4 options:

STATIC:

See 6.6.3.1. Static Color

EFFECT 1, 2, 3:

See 6.6.3.2. Built-in Effects

  1. Press the SET button to confirm.

Static Colors

In this menu you can set the static colors.

  1. Press the UP/DOWN buttons to select one of the 4 submenus:

DIMMER:

From low to high intensity (0­100 %)

WHITE POINT:

Set the color temperature (2000 K, 2200 K, 2400 K, 2600 K, 2800 K, 3000 K,

3200 K, 3600 K, 4200 K, 5600 K, 6500 K, 8000 K) and the tint (From -100 to

+100 %)

PRESET COLOR:

Use one of the Lee color presets (see 6.7. DMX Channels on page 35 for the

full list of presets)

RAW COLOR:

Set the intensity of the LEDs (Red, Green, Blue, Mint), from low to high

intensity (0­255)

  1. Press the SET button to open submenus.

  2. Press the UP/DOWN buttons to adjust values.

  3. Press the SET button to confirm.

Product code: 200500

27

Raccoon P14/4
Built-in Effects In this menu you can run the built-in effects and adjust their settings. 01) Press the UP/DOWN buttons to select one of the 4 options:

DIMMER: From low to high intensity (0­100 %)

PERIOD:

Built-in effect duration (2­60 seconds)

FADE IN: From fast to slow (0­100 %)

FADE OUT: From fast to slow (0­100 %)

  1. Press the SET button to open submenus.

  2. Press the UP/DOWN buttons to adjust values.

  3. Press the SET button to confirm.

Dimmer Curve Selection

In this menu you can select dimming curves.

  1. Press the UP/DOWN buttons to select one of the following 4 options:

  2. Press the SET button to confirm.

Product code: 200500

28

Raccoon P14/4
Dimmer Speed In this menu you can set the dimmer speed. 01) Press the UP/DOWN buttons to choose one of the 4 options:

AUTO: Fast dimmer with jump detection

SLOW: Slow dimmer

MEDIUM: Medium dimmer

FAST:

Light output will follow DMX dimmer value directly

  1. Press the SET button to confirm.

Color Space Selection

In this menu you can set the color space.

  1. Press the UP/DOWN buttons to choose one of the 4 options:

NATIVE SRGB REC. 2020 PROPHOTO RGB 02) Press the SET button to confirm.
Tungsten Mode
In this menu you can set the tungsten settings.

  1. Press the UP/DOWN buttons to choose one of the 4 options:

OFF 575/750 W 1000 W 2000 W 02) Press the SET button to confirm.

Product code: 200500

29

Raccoon P14/4
LED Mode In this menu you can set the LED performance settings. 01) Press the UP/DOWN buttons to choose one of the 2 options:

HIGH QUALITY HIGH BRIGHTNESS 02) Press the SET button to confirm.
Calibration
In this menu you can set the color calibration.

  1. Press the UP/DOWN buttons to choose one of the 2 options:

OFF:

The device will not calibrate the colors and will operate at full output

ON:

The device will calibrate the colors to ensure that there are not any color differences

among multiple Raccoon devices. The output power will slightly decrease.

  1. Press the SET button to confirm.

LED Frequency

In this menu you can set the LED frequency.

  1. Press the UP/DOWN buttons to choose one of the 6 settings:

640 Hz 1280 Hz 2500 Hz 5 kHz 10 kHz 25 kHz 02) Press the SET button to confirm.

Product code: 200500

30

Raccoon P14/4
Display Settings In this menu you can adjust the display settings of the device. 01) Press the UP/DOWN buttons to select one of the following 3 submenus:
BACKLIGHT: See 6.6.11.1. Backlight DISPLAY FLIP: See 6.6.11.2. Display Flip KEY LOCK: See 6.6.11.3. Key Lock 02) Press the SET button to open submenus.
Backlight In this menu you can adjust the behavior of the display. 01) Press the UP/DOWN buttons to select one of the following 3 options:
AUTO: After 20 seconds of inactivity, the display shows the start screen. Press any button to return to the main menu.
STAY ON: The display remains continuously on. STAY OFF: After 20 seconds of inactivity, the display turns off. Press any button to return to the
main menu. 02) Press the SET button to confirm.
Display Flip In this menu you can rotate the display by 180°. 01) Press the UP/DOWN buttons to select one of the following 2 options:
REGULAR: Regular view TOP DOWN: The display will be rotated by 180° 02) Press the SET button to confirm.

Product code: 200500

31

Raccoon P14/4
Key Lock In this menu you can set the display lock. 01) Press the UP/DOWN buttons to select one of the following 2 options:

LOCKED: The display will be locked. UNLOCKED: The display will be unlocked 02) Press the SET button to confirm.
Note:
If no button is pressed, after 20 seconds of inactivity the display turns off. Wait 10 seconds for the display lock to work. If you press any button too early, the display will remain unlocked, even if LOCKED is selected in the menu.
If the display is locked, you need to enter a password to open the main menu. Press the buttons in the following order: UP, DOWN, UP, DOWN, to unlock the display.
DMX Failure
In this menu you can determine the behavior of the device in case there is no DMX signal.

  1. Press the UP/DOWN buttons to select one of the following 3 options:

BLACKOUT: The device will black out the light output

HOLD:

The device will use the last correctly received DMX signal

MANUAL: The device will use the manually selected values for color. See 6.6.3. Manual Mode

on page 27 for more information

  1. Press the SET button to confirm.

Product code: 200500

32

Raccoon P14/4
System Information In this menu you can view the parameters of the device. 01) Press the UP/DOWN buttons to select one of the following 9 submenus:

OPERATING HOURS: Provides information about the total hours of operation of the device

SOURCE HOURS: Provides information about the total hours of operation of the LEDs

POWER CYCLES: Provides information about how many times the device was powered up

POWER:

Provides real-time status of the power consumption of the device. See

6.6.13.1. Power Consumption Status.

LED TEMPERATURE: Provides information about the temperature of the LEDs

RDM ID:

Shows the unique ID number of the device (29B4:0AA*****)

PRODUCT:

Shows the name of the device

DEVICE LABEL:

Shows the device label of the device

VERSION:

Shows the current firmware version

Press the SET button to open submenus.

Power Consumption Status

To see the real-time status of the power consumption, follow the steps below:

  1. Activate the Manual mode and make sure that the light output is on. See 6.6.3. Manual Mode on page 27 for more information.
  2. Do not press any buttons and wait 20 seconds until the display turns off.
  3. Enter the password (if needed) and open the main menu. See 6.4. Start-up on page 21 for more
    information. The light output should still be on. 04) Open this submenu to view the real-time status of the power consumption.

Note:

If you open this submenu without waiting for the display to turn off first, it is not possible to view the realtime status of the power consumption. If you leave the Manual menu manually, the light output turns off and the display reads “0 W”.

Product code: 200500

33

Raccoon P14/4
Sending Settings In this menu you can use DMX to send your current settings to the other connected Raccoon devices. 01) Press the UP/DOWN buttons to select one of the following 3 options:

ABORT:

Return to the previous screen

WITHOUT DMX ADDR:

Send all the settings (apart from the DMX starting address) to the

other connected Raccoon devices

WITH DMX ADDRESS:

Send all the settings (including the DMX starting address) to the other

connected Raccoon devices

  1. Press the SET button to confirm.

Restore Factory Settings

In this menu you can reset the settings of the device to the default factory settings.

  1. Press the UP/DOWN buttons to select one of the following 2 options:

ABORT:

Return to the previous screen

RESET SETTINGS:

Reset all settings

  1. Press the SET button to confirm.

Product code: 200500

34

Raccoon P14/4

DMX Channels

DMX Channels Overview

Function
Dimmer Coarse Dimmer Fine Strobe Hue Coarse Hue Fine Saturation Intensity X Coarse X Fine Y Coarse Y Fine CCT Tint Red Coarse Red Fine Green Coarse Green Fine Blue Coarse Blue Fine Mint Coarse Mint Fine Cyan Coarse Cyan Fine Magenta Coarse Magenta Fine Yellow Coarse Yellow Fine Color Presets Color Saturation Control

Dimmer 1 CH 1

Pixel 3 CH
1 2 3

Basic 8 CH
1 2 3
4 5
6 7 8

XY 8 CH
1 2 3
4 5 6 7
8

Raw 8 CH

HSI 10 CH
1 2 3 4 5 6 7

RGB 12 CH
1 2 3

CMY 12 CH
1 2 3

1

4

2

5

3

6

4

7

5

8

6

9

7

8

4

5

6

7

8

9

8

10

10

9

11

11

10

12

12

Product code: 200500

35

Raccoon P14/4

Dimmer (1 Channel), Pixel (3 Channels), XY (8 Channels), Raw (8 Channels)

Dimmer 1 CH 1

Pixel 3 CH
1 2 3

XY 8 CH
1 2 3
4 5 6 7
8

Raw 8 CH
1 2 3 4 5 6 7 8

Function Dimmer Coarse Dimmer Fine
Strobe
Red Coarse Red Fine Green Coarse Green Fine Blue Coarse Blue Fine Mint Coarse Mint Fine X Coarse X Fine Y Coarse Y Fine
Control

Value
000­255 000­255 000­005 006­125 126­129 130­249 250­255 000­255 000­255 000­255 000­255 000­255 000­255 000­255 000­255 000­255 000­255 000­255 000­255 000­007 008­015 016­023 024­031 032­039 040­047 048­053 054­059 060­065 066­071 072­079 080­087 088­095 096­103 104­111 112­119 120­127 128­135 136­143 144­151 152­159 160­167 168­175 176­183 184­191 192­199 200­207 208­215 216­223 224­230 231­237 238­243 244­250 251­255

Setting
From low to high intensity (0­100 %) From low to high intensity (0­100 %) Closed (No light output) Strobe, from low to high frequency Open Random strobe, from low to high frequency Open From low to high intensity (0­100 %) From low to high intensity (0­100 %) From low to high intensity (0­100 %) From low to high intensity (0­100 %) From low to high intensity (0­100 %) From low to high intensity (0­100 %) From low to high intensity (0­100 %) From low to high intensity (0­100 %) 0­100 % 0­100 % 0­100 % 0­100 % No function Dimmer curve: Linear Dimmer curve: S-Curve Dimmer curve: Square Law Dimmer curve: Inverse Sq. Law Dimmer speed: Auto Dimmer speed: Slow Dimmer speed: Medium Dimmer speed: Fast Simulation source: Tungsten off Simulation source: Tungsten 575 W Simulation source: Tungsten 750 W Simulation source: Tungsten 1000 W Simulation source: Tungsten 2000 W PWM frequency: 640 Hz PWM frequency: 1280 Hz PWM frequency: 2500 Hz PWM frequency: 5 kHz PWM frequency: 10 kHz PWM frequency: 25 kHz Calibration: disabled Calibration: enabled Reserved Reserved Reserved Graphic display: Auto Off Graphic display: On CCT mode: High CRI CCT mode: High Output Color space: Native Color space: sRGB Color space: Rec. 2020 Color space: ProPhoto RGB Reset all control channel settings

Product code: 200500

36

Raccoon P14/4

Basic (8 Channels), HSI (10 Channels) RGB (12 Channels), CMY (12 Channels)

Basic 8 CH
1 2

HSI 10 CH
1 2

RGB 12 CH
1 2

CMY 12 CH
1 2

Function
Dimmer Coarse Dimmer Fine

3

3

3

3 Shutter/Strobe

4

Hue Coarse

5

Hue Fine

6

Saturation

7

Intensity

4

CCT

5

Tint

4

Red Coarse

5

Red Fine

6

Green Coarse

7

Green Fine

8

Blue Coarse

9

Blue Fine

4 Cyan Coarse

5 Cyan Fine

6 Magenta Coarse

7 Magenta Fine

8 Yellow Coarse

9 Yellow Fine

6

8

10

10 Color Presets

Value Setting

000­255 000­255 000­005 006­125 126­129 130­249
250­255 000­255 000­255 000­255 000­255
000
001­031 032­057 058­078 079­097 098­113 114­128 129­146 147­170 171­189 190­204 205­216 217­227 228­235 236­243 244­249 250­255 000­255 000­255 000­255 000­255 000­255 000­255 000­255 000­255 000­255 000­255 000­255 000­255 000­255 000­007 008­010 011­013 014­016 017­019 020­022 023­025 026­028 029­031 032­034 035­037

From low to high intensity (0­100 %)

From low to high intensity (0­100 %)

Closed (No light output)

Strobe, from low to high frequency

Open

Random strobe, from low to high

frequency

Open

From low to high intensity (0­100 %)

From low to high intensity (0­100 %)

From low to high intensity (0­100 %)

From low to high intensity (0­100 %)

2000 K

2000­2200 K

2200­2400 K

2400­2600 K

2600­2800 K

2800­3000 K

3000­3200 K

3200­3500 K

3500­4000 K

4000­4500 K

4500­5000 K

5000­5500 K

5500­6000 K

6000­6500 K

6500­7000 K

7000­7500 K

7500­8000 K

Tint, from -100 % to 100 %

From low to high intensity (0­100 %)

From low to high intensity (0­100 %)

From low to high intensity (0­100 %)

From low to high intensity (0­100 %)

From low to high intensity (0­100 %)

From low to high intensity (0­100 %)

From low to high intensity (0­100 %)

From low to high intensity (0­100 %)

From low to high intensity (0­100 %)

From low to high intensity (0­100 %)

From low to high intensity (0­100 %)

From low to high intensity (0­100 %)

No function

Medium Bastard Amber

L004

Fire

L019

Bright Red

L026

Lavender

L058

Sky Blue

L068

Just Blue

L079

Lime Green

L088

Dark Yellow Green

L090

Spring Yellow

L100

Yellow

L101

Product code: 200500

37

Raccoon P14/4

Basic HSI 8 CH 10 CH

RGB 12 CH

CMY 12 CH

Function

Product code: 200500

Value Setting

038­040 041­043 044­046 047­049 050­052 053­055 056­058 059­061 062­064 065­067 068­070 071­073 074­076 077­079 080­082 083­085 086­088 089­091 092­094 095­097 098­100 101­103 104­106 107­109 110­112 113­115 116­118 119­121 122­124 125­127 128­130 131­133 134­136 137­139 140­142 143­145 146­148 149­151 152­154 155­157 158­160 161­163 164­166 167­169 170­172 173­175 176­178 179­181 182­184 185­187 188­190 191­193 194­196 197­199 200­255

Light Amber Straw Deep Amber Orange Primary Red Dark Pink Magenta Peacock Blue Medium Blue Green Steel Blue Light Blue Dark Blue Deep Blue Lee Green Fern Green Dark Green Bright Pink Medium Blue Golden Amber Deep Golden Amber Pale Lavender Special Lavender Pale Green Primary Green Bright Blue Apricot Bright Rose Pale Gold Pink Deep Orange Bastard Amber Flame Red Daylight Blue Lilac Tint Deep Lavender Lagoon Blue Chrome Orange Dark Lavender Congo Blue Alice Blue Full CT Blue Half CT Blue Quarter CT Blue Full CT Orange Half CT Orange Quarter CT Orange LEE Minus Green Half Minus Green Three Quarter CT Blue Three Quarter CT Orange Follies Pink Lighter Blue Millennium Gold Vanity Fair Reserved

38

L102 L103 L104 L105 L106 L111 L113 L115 L116 L117 L118 L119 L120 L121 L122 L124 L128 L132 L134 L135 L136 L137 L138 L139 L141 L147 L148 L152 L157 L158 L162 L164 L165 L169 L170 L172 L179 L180 L181 L197 L201 L202 L203 L204 L205 L206 L247 L248 L281 L285 L328 L353 L778 L793

Raccoon P14/4

Basic HSI

8 CH 10 CH

7

9

RGB 12 CH
11

CMY 12 CH
11

Function Color Saturation

8

10

12

12 Control

Value Setting

000­255 000­007 008­015 016­023 024­031 032­039 040­047 048­053 054­059 060­065 066­071 072­079 080­087 088­095 096­103 104­111 112­119 120­127 128­135 136­143 144­151 152­159 160­167 168­175 176­183 184­191 192­199 200­207 208­215 216­223 224­230 231­237 238­243 244­250 251­255

Color filter saturation, from 100 % to 0 % No function Dimmer curve: Linear Dimmer curve: S-Curve Dimmer curve: Square Law Dimmer curve: Inverse Sq. Law Dimmer speed: Auto Dimmer speed: Slow Dimmer speed: Medium Dimmer speed: Fast Simulation source: Tungsten off Simulation source: Tungsten 575 W Simulation source: Tungsten 750 W Simulation source: Tungsten 1000 W Simulation source: Tungsten 2000 W PWM frequency: 640 Hz PWM frequency: 1280 Hz PWM frequency: 2500 Hz PWM frequency: 5 kHz PWM frequency: 10 kHz PWM frequency: 25 kHz Calibration: disabled Calibration: enabled Reserved Reserved Reserved Graphic display: Auto Off Graphic display: On CCT mode: High CRI CCT mode: High Output Color space: Native Color space: sRGB Color space: Rec. 2020 Color space: ProPhoto RGB Reset all control channel settings

Product code: 200500

39

Raccoon P14/4

RDM Information

This device supports RDM. Refer to 6.8.2. Supported RDM PIDs (Parameter IDs) for more information.

RDM Details

Responder: Manufacturer’s ID: Manufacturer Label: Model Description: Model ID: Device Label:

29B4:0AAxxxxx Infinity (Highlite International B.V.) Infinity Raccoon P14/4 170 (0AA hexadecimal) Raccoon P14/4

Note:

An RDM responder ID consists of 3 parts:

1st part ­ 4 digits ­ Manufacturer’s ID 2nd part ­ 3 digits ­ Model ID 3rd part ­ 5 digits ­ Unique ID

The RDM responder IDs of all products of Highlite International start with the same 4 digits. The first 7 digits of the RDM responder ID for each model are the same. The last 5 digits are different for each device.

Supported RDM PIDs (Parameter IDs)

Parameter ID
DISC_UNIQUE_BRANCH DISC_MUTE DISC_UN_MUTE SUPPORTED_PARAMETERS DEVICE_INFO DEVICE_MODEL_DESCRIPTION MANUFACTURER_LABEL DEVICE_LABEL FACTORY_DEFAULTS SOFTWARE_VERSION_LABEL BOOT_SOFTWARE_VERSION_ID BOOT_SOFTWARE_VERSION_LABEL DMX_PERSONALITY DMX_PERSONALITY_DESCRIPTION DMX_START_ADDRESS SENSOR_DEFINITION SENSOR_VALUE DEVICE_HOURS LAMP_HOURS LAMP_STRIKES DEVICE_POWER_CYCLES IDENTIFY_DEVICE RESET_DEVICE

Value

Required

GET

SET

0x0001

0x0002

0x0003

0x0050

0x0060

0x0080

0x0081

0x0082

0x0090

0x00C0

0x00C1

0x00C2

0x00E0

0x00E1

0x00F0

0x0200

0x0201

0x0400

0x0401

0x0402

0x0405

0x1000

0x1001

Product code: 200500

40

Raccoon P14/4

7. Troubleshooting

This troubleshooting guide contains solutions to problems which can be carried out by an ordinary person. The device does not contain user-serviceable parts.

Unauthorized modifications to the device will render the warranty void. Such modifications may result in injuries and material damage.

Refer servicing to instructed or skilled persons. Contact your Highlite International dealer in case the solution is not described in the table.

Problem The device does not function at all The device responds erratically The device does not respond to DMX control
The device responds erratically to DMX control
No light or LEDs cut out intermittently

Probable cause(s) No power to the device
Internal fuse is blown
The factory settings of the device are changed The controller is not connected The signal is reversed. The 3-pin DMX OUT of the controller does not match the DMX IN of the device The controller is defective
Bad data link connection
The data link is not terminated with a 120 termination plug
Incorrect addressing In case of a setup with multiple devices, one of the devices is defective and disturbs data transmission on the link
LEDs are damaged
The power supply settings do not match local AC voltage and frequency

Solution Check if power is switched on and
cables are plugged in Disconnect the device and contact
your Highlite International dealer Reset the device’s parameters to the
default factory settings. See 6.6.15. Restore Factory Settings on page 34 Connect the controller Install a phase-reversing cable between the controller and the device
Try using another controller Examine connections and cables.
Correct poor connections. Repair or replace damaged cables
Insert a termination plug in the DMX OUT connector of the last device on the link
Check address settings and correct, if necessary
To find out the defective device, bypass one device at a time until normal operation is restored
Disconnect the device and contact your Highlite International dealer
Disconnect the device. Check the settings and correct, if necessary

Product code: 200500

41

Raccoon P14/4
8. Maintenance
Safety Instructions for Maintenance
DANGER Electric shock caused by dangerous voltage inside
Disconnect power supply before servicing or cleaning.
Preventive Maintenance
Attention Before each use, examine the device visually for any defects.
Make sure that: All screws used for installing the device or parts of the device are tightly fastened and are not
corroded. The safety devices are not damaged. There are no deformations on housings, fixations and installation points. The lens is not cracked or damaged. The power cables are not damaged and do not show any material fatigue.
Basic Cleaning Instructions The external lens of the device must be cleaned periodically in order to optimize the light output. The cleaning schedule depends on the conditions at the site where the device is installed. When smoke or fog machines are used at the site, the device will need more frequent cleaning. On the other hand, if the device is installed in well-ventilated area, it will need less frequent cleaning. To establish a cleaning schedule, examine the device at regular intervals during the first 100 hours of operation. To clean the device, follow the steps below: 01) Disconnect the device from the electrical power supply. 02) Allow the device to cool down for at least 15 minutes. 03) Remove the dust collected on the external surface with dry compressed air and a soft brush. 04) Clean the lens with a damp cloth. Use a mild detergent solution. 05) Dry the lens carefully with a lint- free cloth. 06) Clean the DMX and other connections with a damp cloth.
Attention
Do not immerse the device in liquid. Do not use alcohol or solvents. Make sure that the connections are fully dry before connecting the device to the power supply and
to other devices.

Product code: 200500

42

Raccoon P14/4
Draining Condensation Water
The Raccoon P14/4 is IP65 rated. The device can resist water jets. If the device is exposed to extreme humid conditions during servicing, condensation may collect inside the device. This can happen also during transportation, if the device is exposed to extreme temperature variations.
If condensation water collects inside the device, follow the steps bellow to remove the condensation water:

  1. Carefully remove the protective vent (07) with a wrench (16 mm).

Let the device operate at full output for 60 minutes. Let the device cool down for 30 minutes. Install the protective vent (07) again. Make sure that you do not overtighten it.

Fig. 19

Corrective Maintenance

The device does not contain user-serviceable parts. Do not open the device and do not modify the device.

Refer repairs and servicing to instructed or skilled persons. Contact your Highlite International dealer for more information.

Product code: 200500

43

Raccoon P14/4
9. Deinstallation, Transportation and Storage
Instructions for Deinstallation
WARNING Incorrect deinstallation can cause serious injuries and damage of property.
Let the device cool down before dismounting. Disconnect power supply before deinstallation. Always observe the national and site-specific regulations during deinstallation and derigging of the
device. Wear personal protective equipment in compliance with the national and site-specific regulations.
Instructions for Transportation
Use the original packaging to transport the device, if possible. Always observe the handling instructions printed on the outer carton box, for example: “Handle with
care”, “This side up”, “Fragile”.
Storage
Clean the device before storing. Follow the cleaning instructions in chapter 8.2.1. Basic Cleaning Instructions on page 42.
Store the device in the original packaging, if possible.
10. Disposal
Correct disposal of this product Waste Electrical and Electronic Equipment This symbol on the product, its packaging or documents indicates that the product shall not be treated as household waste. Dispose of this product by handing it to the respective collection point for recycling of electrical and electronic equipment. This is to avoid environmental damage or personal injury due to uncontrolled waste disposal. For more detailed information about recycling of this product contact the local authorities or the authorized dealer.
11. Approval
Check the respective product page on the website of Highlite International (www.highlite.com) for an available declaration of conformity.

Product code: 200500

44

Raccoon P14/4

Product code: 200500

45

Raccoon P14/4

Product code: 200500

46

©2022 Infinity

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals