The Crest Company BRBTXL TV Wall Mount User Manual
- June 13, 2024
- The Crest Company
Table of Contents
- The Crest Company BRBTXL TV Wall Mount User Manual
- Hardware Kit Contents
- Tools Required
- DRYWALL INSTALLATION (TIMBER SUPPORTS):
- MASONRY INSTALLATION:
- Step 1: Attach Wall Plate to Wall
- A. INSTALLING IN DRYWALL (TIMBER SUPPORTS)
- b. INSTALLING IN MASONRY
- Step 2: Attach Mounting Arms to TV
- Step 3: Hook Arms Over Wall Plate
- 5 YEAR WARRANTY
- Read More About This Manual & Download PDF:
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
The Crest Company BRBTXL TV Wall Mount User Manual
Hardware Kit Contents
Tools Required
DRYWALL INSTALLATION (TIMBER SUPPORTS):
- Adjustable spanner/socket set
- Long Handled Philips head screwdriver
- Power drill
- High speed 5mm drill bit
- Stud finder
- Spirit level and pencil
MASONRY INSTALLATION:
- Adjustable spanner/socket set
- Philips head screwdriver
- Power drill with hammer function
- 10mm Masonry drill bit
- Spirit level and pencil
- Hammer
Step 1: Attach Wall Plate to Wall
A. INSTALLING IN DRYWALL (TIMBER SUPPORTS)
WARNING: If attaching this TV Wall Mount using this method, you MUST centre
the wall plate across 2 wall studs. Wall studs can be 450mm or 600mm apart
depending upon the position of the wall and the geographical state you live
in. The Crest Company will not accept any damages that may occur if only 1
stud is used.
The Crest Company holds no responsibility for incorrectly installed TV Wall
Mounts.
- Locate the centre of two adjacent timber studs using a stud finder(NOTE: You must use the centre of the stud to avoid cracking or splitting the timber during installation).
- Mark a minimum of 4 fixing holes over stud centres using the wall plate as a guide – position 2 at either end of the Wall Ensure plate is level.
- Pre-drill holes to a minimum depth of 55mm using a high speed 5mm drill bit. If installing in hardwood, larger diameter and deeper holes may be required.
- Attach the wall plate (B) using the lag bolts (W-A) through the washers (W-C). Do not over tighten
b. INSTALLING IN MASONRY
WARNING: Ensure you have a minimum of 35mm of actual concrete/brick thickness
in the hole for the anchors. Do not drill into mortar joints. Installer must
verify that the supporting surface will safely support the combined weight of
the TV Wall Mount and TV.
The Crest Company holds no responsibility for incorrectly installed TV Wall
Mounts.
- Mark a minimum of four fixing holes using the Wall Plate as a guide – position 2 at either end of the Wall Ensure plate is level.
- Pre-drill holes to a minimum depth of 60mm using 10mm masonry drill Clean out holes.
- Fully insert concrete anchors (W-B). Tap in with hammer if
- Attach wall plate (B) by inserting the lag bolts (W-A) through the washers (W-C) into each concrete anchor (W-B). Do not over
Step 2: Attach Mounting Arms to TV
The Crest Company endeavours to provide the correct sized bolts required to mount the arms to the back of the TV, however this may not be possible for all TV models. If this is the case please purchase the correct sized bolts from your local hardware.
-
Using a second person for assistance, lay your TV face down on something soft so as not to scratch the TV
Check the back of your TV to find the appropriate mounting pattern. -
Sort through the provided bolts (M-A to M-E) until you find the correct size that easily fits into the back of your TV and fits snugly (the bolt must turn at least 3 full turns, do not tighten). If you feel resistance stop immediately and select a smaller
-
Once you have selected the correct bolt size, use the multi-washer (M-F). If no bolts fit you will need to go to your local hardware supplier to find the correct bolt and washer
-
Gently put your mounting arms on the back of the TV so that the mounting holes are showing through the holes of the mounting arms.
If the back of your TV is curved or recessed you will also need to use a spacer (M-G or M-H) depending upon the amount of space you are trying to clear. If using a spacer you will also need to use longer screws. Remember that the bolt needs toturn at least 3 full turns. -
Using the correct mounting bolt size and length, insert these through the corresponding hole on the washer (M-F) to attach mounting arms to the rear of the TV. To avoid damaging TV, do not over tighten bolts.
The Crest Company is not responsible for any damage caused by screwing the bolt too far into the back of the TV
Step 3: Hook Arms Over Wall Plate
- Using a second person for assistance, carefully lift the TV and hook arms over the top of the wall
- Slowly lower the bottom of the TV until the bottom of the mounting arm locks into the bottom of the wall
- Once your TV is in place close the lock at the bottom of the mounting arms and tighten with a long handled screw This will help ensure that your TV does not fall off your wall plate during use.
- To remove the TV from the wall plate, loosen the screws at the bottom of the mounting arms which will release the mounting Pull the bottom of the TV slightly towards you and then lift the TV from the wall plate.
- Tighten nuts and bolts as
- TV can be tilted forward as desired by loosening the control on the side of the mounting arms. Check your TV Wall Mount is secure and safe to use at regular intervals (at least every three months).
5 YEAR WARRANTY
Olbertz Holdings Pty Ltd ACN 010 003 933 trading as The Crest Company of 165
South Pine Road, Brendale, Queensland, 4500, Ph: 1800 812 261,
www.crest.com.au, warrants that if this Crest
product purchased by you from The Crest Company or a retail outlet is found by
The Crest Company to be defective in workmanship or materials within 5 years
of the date of purchase, The Crest Company will (at its election) either
repair that product, replace the product, supply an equivalent product or pay
the costs of repairing or replacing the product or acquiring an equivalent
product.
This limited warranty will not extend to or cover any expenses associated with
removing, demounting the original product or installing the repaired, replaced
or equivalent product or all or any of its components, you must bear these
expenses. It also does not cover damage or loss resulting from intentional or
unintentional misuse of, tampering with, alterations to or incorrect
installation of this product or use of this product for purposes other than
that for which it is designed or in a manner inconsistent with the product’s
instructions. This limited warranty also does not apply to damage or loss
resulting from fair wear and tear or events beyond The Crest Company control
including but not limited to natural disasters.
In order to claim under this warranty, you must contact The Crest Company and
return to The Crest Company (via our nominated reply paid address) the product
and its components and proof of purchase (including the date and location of
purchase) so that The Crest Company can verify the defect and your purchase.
Our goods come with guarantees that cannot be excluded under the Australian
Consumer Law. You are entitled to a replacement or refund for a major failure
and compensation for any other reasonably foreseeable loss or damage. You are
also entitled to have the goods repaired or replaced if the goods fail to be
of acceptable quality and the failure does not amount to a major failure. The
benefits given by this warranty are in addition to other rights and remedies
which you may have under a law in relation to the goods or services to which
the warranty relates.
Read More About This Manual & Download PDF:
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>