The Crest Company MFP1TL TV Wall Mount Instruction Manual
- June 13, 2024
- The Crest Company
Table of Contents
The Crest Company MFP1TL TV Wall Mount
Product Information
The TV Wall Mount is a lockable, anti-theft heavy-duty tilt wall mount designed to securely hold TV screens. It includes a locking bar for anti-theft purposes, although a padlock is not included. The mount is compatible with TV screens ranging from 37-90 inches (94-228cm) in size. It has a maximum mounting pattern of 600x400mm (WxH) and can support TVs weighing up to 100kg. The mount also offers a tilt range for optimal viewing angles.
Product Usage Instructions
Safety Precautions:
- Installation of this TV Wall Mount is easier with two people.
- Some images in the guide may vary slightly from the actual components supplied.
- Read and understand the instruction manual completely before attempting installation.
- The TV Wall Mount must not be installed solely in plasterboard, fibre cement, and similar surfaces.
- The TV Wall Mount must be installed in sound supporting hardware.
Hardware Kit Contents:
- W-A: 6.3 x 55mm Lag Bolt (Qty: 6)
- W-B: 10 x 6 x 50mm Anchor (Qty: 6)
- W-C: D66x W16asxh1e.r5mm Washer (Qty: 6)
- M-A: M5 x 14mm Bolt (Qty: 4)
- M-B: M6 x 14mm Bolt (Qty: 4)
- M-C: M6 x 30mm Bolt (Qty: 4)
- M-D: M8 x 30mm Bolt (Qty: 4)
- M-E: M8 x 50mm Bolt (Qty: 4)
- M-F: Multi-sized Washer (Qty: 4)
- M-G: Spacer (Qty: 8)
- M-H: Spacer (Qty: 8)
- A: Wall Plate (Qty: 1)
- B: Left Mounting Arm (Qty: 1)
- C: Right Mounting Arm (Qty: 1)
- D: M6 Lock Nut (Qty: 2)
- E: Black D6 Washer (Qty: 2)
- F: Lockable Bar (Qty: 1)
Tools Required:
For drywall installation:
- Stud finder
- High-speed 4.5mm drill bit
For masonry installation:
- Hammer drill
- Masonry drill bit
Drywall Installation (Timber Supports):
Step 1: Attach Wall Plate to Wall
- INSTALLING IN DRYWALL (TIMBER FRAME)
WARNING: If attaching this TV Wall Mount using this method, you MUST center the wall plate across 2 wall studs. Wall studs can be 450mm or 600mm apart depending upon the position of the wall and the geographical state you live in. The Crest Company will not accept any damages that may occur if only 1 stud is used. The Crest Company holds no responsibility for incorrectly installed TV Wall Mounts.
- Locate the center of two adjacent timber studs using a stud finder.
- Mark a minimum of 4 fixing holes over stud centers using the wall plate as a guide – position 2 at either end of the Wall Plate (see Figure 1A). Ensure the plate is level.
- Pre-drill holes to a minimum depth of 50mm using a high-speed 4.5mm drill bit. If installing in hardwood, larger diameter and deeper holes may be required.
- Attach the wall plate (A) using the lag bolts (W-A) through the washers (W-C). Do not over tighten.
INSTALLING IN MASONRY
[Instructions for masonry installation are missing from the provided text
extract.]
MFP1TL TV Wall Mount
-
Lockable
Anti-theft heavy duty Tilt Wall Mount. Includes Locking Bar for anti-theft (padlock required) -
Compatible TV Size
This TV Wall Mount fits 37-90” (94-228cm) TV Screens -
Maximum Mounting Pattern
This TV Wall Mount has a mounting hole pattern up to 600x400mm (WxH) -
Maximum TV Weight
This TV Wall Mount supports TVs weighing up to 100kg -
Tilt Range
This TV Wall Mount can tilt +/- 15 Degrees
SAFETY FIRST
- Installation of this TV Wall Mount will be easier with two people.
- Some images in this guide may vary slightly from the actual components supplied.
- Ensure this instruction manual is completely read and understood before attempting installation.
- This TV Wall Mount MUST NOT be installed solely in plasterboard, fibre cement and similar surfaces.
- This TV Wall Mount MUST be installed in sound supporting structures such as those made of timber, steel or masonry using appropriate fasteners.
- The supporting structure must be capable of sustaining the combined weight of the TV Wall Mount and the display otherwise the structure must be reinforced.
- The fasteners supplied in this hardware pack allow for fixing into timber and masonry only. If installing into a supporting structure made of steel, appropriate fasteners must be used and sourced from an appropriate supplier.
- Use appropriate tools and safety equipment and ensure adequate ventilation during installation.
- If uncertain about any aspect of installation, contact The Crest Company or an installation professional.
- Please retain these instructions for future reference.
Dimension
Hardware Kit Contents
Tools Required
DRYWALL INSTALLATION (TIMBER SUPPORTS)
- Adjustable spanner/socket set
- Philips head screwdriver
- Power drill
- High speed 4.5 mm drill bit
- Stud finder
- Spirit level and pencil
MASONRY INSTALLATION
- Adjustable spanner/socket set
- Philips head screwdriver
- Power drill with hammer function
- 10mm Masonry drill bit
- Spirit level and pencil
- Hammer
Step 1: Attach Wall Plate to Wall
A. INSTALLING IN DRYWALL (TIMBER FRAME)
WARNING: If attaching this TV Wall Mount using this method, you MUST centre
the wall plate across 2 wall studs. Wall studs can be 450mm or 600mm apart
depending upon the position of the wall and the geographical state you live
in. The Crest Company will not accept any damages that may occur if only 1
stud is used.
The Crest Company holds no responsibility for incorrectly installed TV Wall
Mounts.
-
Locate the centre of two adjacent timber studs. Crest recommends the use of a stud finder (not included).
(NOTE: You must use the centre of the stud to avoid cracking or splitting the timber during installation). -
Mark a minimum of 4 fixing holes over stud centres using the wall plate as a guide – position 2 at either end of the Wall Plate (see Figure 1A). Ensure plate is level.
-
Pre-drill holes to a minimum depth of 50mm using a high speed 4.5mm drill bit. If installing in hardwood, larger diameter and deeper holes may be required.
-
Attach the wall plate (A) using the lag bolts (W-A) through the washers (W-C). Do not over tighten.
INSTALLING IN MASONRY
WARNING: Ensure you have a minimum of 35mm of actual concrete/brick
thickness in the hole for the anchors. Do not drill into mortar joints.
Installer must verify that the supporting surface will safely support the
combined weight of the TV Wall Mount and TV.
The Crest Company holds no responsibility for incorrectly installed TV Wall
Mounts.
- Mark a minimum of four fixing holes (preferably 6) using the Wall Plate as a guide – position 2 at either end of the Wall Plate (see Figure 1B). Ensure plate is level.
- Pre-drill holes to a minimum depth of 60mm using 10mm masonry drill bit. Clean out holes.
- Fully insert concrete anchors (W-B). Tap in with hammer if required.
- Attach wall plate (A) by inserting the lag bolts (W-A) through the washers (W-C) into each concrete anchor (W-B). Do not over tighten.
Step 2: Attach Mounting Arms to TV
The Crest Company endeavours to provide the correct sized bolts required to
mount the arms to the back of the TV, however this may not be possible for all
TV models. If this is the case please purchase the correct sized bolts from
your local hardware.
- Using a second person for assistance, lay your TV face down on something soft so as not to scratch the TV screen.
- Check the back of your TV to find the appropriate mounting pattern.
- Sort through the provided bolts (M-A to M-E) until you find the correct size that easily fits into the back of your TV and fits snugly (the bolt must turn at least 3 full turns, do not tighten). If you feel resistance stop immediately and select a smaller bolt. Once you have selected the correct bolt size, use the multi-sized washer (M-F). If no bolts fit you will need to go to your local hardware supplier to find the correct bolt and washer sizes.
- Screw Lock Nuts (D) through Black Washers (E) into Left and Right Mounting Arms (B/C) to lock in the required tilt angle (see figure 2A). It is important to attached the Lock Nuts to the opposite side of each Mount Arm (see figure 2A)
- Gently put your mounting arms (B and C) on the back of the TV so that the mounting holes are showing through the holes of the mounting arms (see Figure 2B). If the back of your TV is curved or recessed you will also need to use spacers (M-G and M-H) depending upon the amount of space you are trying to clear. If using a spacer you will also need to use longer screws. Remember that the bolt needs to turn at least 3 full turns.
- Using the correct mounting bolt size and length, insert these through the corresponding hole on the multi-sized washer (M-F) to attach mounting arms to the rear of the TV (see Figure 2B). To avoid damaging TV, do not over tighten bolts. The Crest Company is not responsible for any damage caused by screwing the bolt too far into the back of the TV.
Step 3: Hook Arms Over Wall Plate
- Using a second person for assistance, carefully lift the TV and hook arms over the top of the wall plate (see Figure 3).
- Slowly lower the bottom of the TV until the bottom of the mounting arm locks on the wall plate. This will help ensure that your TV does not fall off your wall plate during use (see Figure 3).
- Slide lockable bar (F) through the mounting arms and secure with padlock (not included) (See figure 4).
Check your TV Wall Mount is secure and safe to use at regular intervals (at least every three months).
5 YEAR WARRANTY
Olbertz Holdings Pty Ltd ACN 010 003 933 trading as The Crest Company of 165
South Pine Road, Brendale, Queensland, 4500, Ph: 1800 812 261,
www.crest.com.au, warrants that if this Crest
product purchased by you from The Crest Company or a retail outlet is found by
The Crest Company to be defective in workmanship or materials within 5 years
of the date of purchase, The Crest Company will (at its election) either
repair that product, replace the product, supply an equivalent product or pay
the costs of repairing or replacing the product or acquiring an equivalent
product.
This limited warranty will not extend to or cover any expenses associated with
removing, demounting the original product or installing the repaired, replaced
or equivalent product or all or any of its components, you must bear these
expenses. It also does not cover damage or loss resulting from intentional or
unintentional misuse of, tampering with, alterations to or incorrect
installation of this product or use of this product for purposes other than
that for which it is designed or in a manner inconsistent with the product’s
instructions. This limited warranty also does not apply to damage or loss
resulting from fair wear and tear or events beyond The Crest Company control
including but not limited to natural disasters.
In order to claim under this warranty, you must contact The Crest Company and
return to The Crest Company (via our nominated reply paid address) the product
and its components and proof of purchase (including the date and location of
purchase) so that The Crest Company can verify the defect and your purchase.
Our goods come with guarantees that cannot be excluded under the Australian
Consumer Law. You are entitled to a replacement or refund for a major failure
and compensation for any other reasonably foreseeable loss or damage. You are
also entitled to have the goods repaired or replaced if the goods fail to be
of acceptable quality and the failure does not amount to a major failure. The
benefits given by this warranty are in addition to other rights and remedies
which you may have under a law in relation to the goods or services to which
the warranty relates.
- PO Box 5658 Brendale
- QLD Australia 4500
- Customer Support
- 1800 812 261 www.crest.com.au
- AUSTRALIAN OWNED
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>