NINJA Dragon Phantom Z 4K Dual Camera Drone Instruction Manual

NINJA Dragon Phantom Z 4K Dual Camera Drone Instruction Manual

Important safety information

1. The product is not a toy, but the mechanical, electronic, aerodynamics, high-frequency transmission and other professional knowledge into one of the fine Dense equipment, the need for proper assembly and commissioning to avoid accidents. The product holder must use a safe way.Operation control: improper operation, may cause serious personal injury or property damage. We are not responsible for this,Because we can not control the assembly, use, operation process.
2. This product is suitable for people with operating model experience, the age of not less than 14 years of age.
3. The flight site must be a local legal remote control model flight site.
4. Once the product is sold, we will not be responsible for any safety and safety arising from operation and use, control, etc.
5. If any using, operating and measuring problems, please contact with local distributors, for we have assigned those distributors to provide technical support and after sales service.

Safety Precautions:

Remote control model aircraft is a high-risk goods, must be away from the crowd when flying. Atificial assembly or body damage, electronic control.Improper equipment, and operation are not familiar with, are likely to cause damage to the aircraft or personal injury and other unpredictable accidents. please.Pilots must pay attention to safety, and need to understand due to their own negligence caused by accidental responsibility.

1. Away from obstacles and crowds
   The flight of the remote control flight has an uncertain flight speed and state, there is a potential risk. Fly away from the flight.People, high-rise buildings, high-voltage wires, etc., while avoiding wind and rain, thunderstorms and other bad weather flight to ensure that pilots, The surrounding population and the safety of the property.

2. Away from the damp environment
   The interior of the aircraft is made up of many sophisticated electronic components and mechanical parts, s0 it is necessary to prevent the aircraft from wet or Into the body, so as to avoid mechanical, electronic components failure caused by accidents!

3. Safe operation
   Please operate the remote control aircraft according to your own status and flight skills. Fatigue, poor spirit or improper operation will increase. Probability of accidental risk.

4. Keep away from high-speed rotating parts
   When the propeller in the high-speed flight, the pilot, the surrounding crowd and objects away from the0 rotating parts, so as to avoid danger and damage.

5. Keep away from heat
   Remote control aircraft is composed of metal, fiber, plastic, electronic components and other materials, so as far as possible away from heat, to prevent day.Drying, to avoid deformation caused by high temperature or even damage.

The plant is made of lithium polymer battery ( LiPo )

Lithium batteries are different from the general battery, which consists of a thin layer of thin paper wrapped with its chemical endoplasm. This can be great.To reduce its weight, but it makes it more vulnerable in the face of rough or inappropriate operations. Like the same.There is a battery, as inappropriate operation will cause a fire explosion.

• Do not put the battery in the model for charging, which may cause the battery to fire and damage you of the aircraft.
• If you plan to use this product for one week or more, keep the battery 50% Increase the battery life. Keep the battery 50% of the battery, just use the battery when fully charged Half of the time to charge.
• Please use the original professional charger to charge the battery.
• Do not charge the carpet to prevent fire,
• Lithium battery in the storage for more than three months after the need to charge to maintain the voltage to ensure that it shcfuld have Of life.

Remote control and aircraft battery installation and charging instructions

Remote control battery installation:

The aircraft battery is charged 

1. Connect the USB cable to the computer to charge: USB charging end connected to the aircraft battery Blu the’other end can be connected to the computer SB port to chargfe the battery, charging lights, full when the |ights off,
2. Connecting the aircraft power supply:
   Put the charged battery into the battery holder of the aircraft, and then placethe battery plug at the power supply on the vehicle Into the socket for power connection, connected to open the aircraft power, then the aircraft lights.
   

As shown in the figure according to the electrode box electrode instructions (+ / -)  Place the battery correctly (as shown).

Aircraft installation

1. Folding function display
   When folding, please fold the back  Show arms, and then folded in front #of the arm,Expand the opposite!
   

2. Aircraft fan installation
   Please folow the correct direction to install the progeller, prapelier on the sign.Installed to the upper left corner of the aircraft and the ower Right comer of the arm, with the phase With the propeller on the sign 8 mounted to the upper right comer of the aircraft and the | awer left.Corner of the arm, the installationof the fan folder when ° % the alignment of the cone assembly Square accessories, installed in B \Y g A place after the locking screw!
   

3. Aircraft protection rack installation
   The protective frame at the aircraft arm position (pictured)Install fastening.
   

Remote control function name

Remote control

1. Mobile phone rack
   Pull out the remote control lower \ bracket, clamp the phone.
   

2. 24G frequency
   Open the aircraft power switch, the aircraft placed in the flat Ground, then the aircraft indicator light flashes, open the remote control power.Source switch, the throttle joystick pushed to the highest after the pull to the lowest,Buzzer prompt “tick” sound! The aircraft indicator light is on, right Frequency to complete, then you can take off!

3. Akey to start and a key landing
   Tip: This product is determined by the barometer.In a variety of environmental temperature and other factors,The aircraft will automatically start when flying or low voltage. Appear high and low changes are normal!
   

4. Flight control
   A.Throttle (left lever)
   Push the left lever upwards The aircraft rises
   
   Push the left lever down The aircraft descends)
   
   B.Forward and backward (right lever) (with camera front side)
   Push the right lever upwards

The aircraft is advancing

Push the right lever down

The aircraft is backwards

C.Left and right side fly
Push the right lever to the left
The plane flew to the left

Push the right lever to the right
The plane flew to the right

D.Turn left and right (with camera front side)
Turn the left lever to the left
Aircraft turn left

Turn the left lever to the right
Aircraft turn right

5. Fine-tuning control (with cam era front side)
   Forward an backward fine tuning
   Partial rear
   Partial front
   Take off the body when the offset, according to the former micro Adjustment is correct
   Take off when the body forward offset, after the micro Adjustment is correct
   
   About fine tuning
   Left side
   Right side
   Take off the body when the left shift, according to the right micro Adjustment is correct
   Take off the body when the right shift, according to the left micro Adjustment is correct
   

Directional definition and mode selection of headless mode

When converting to headless mode, the aircraft will give up its front and rear azimuths, and reposition the front and rear with the remote control as a reference point. Such as: when the right lever to push forward, the aircraft will fly away from the remote control; when the right lever to pull back, the aircraft will fly to the remote control. (With camera front side)

1. The direction of the aircraft before departure: the direction of the aircraft forward in front of you,(With the camera side for the front) remote control to the end of the direct flight and then press a key.Take off, that is, to complete the flight head mode direction definition.
2. When flying by the headless mode of the remote control issued a “flute, flute” twice, the aircraft lights Light flashing into the headless mode. And then press the remote control  issued a “flute” sound Exit the headless mode.
   

A key return

Press a key return, the aircraft will give up their own front and rear: left and right direction, automatically defined by the headless mode of backward direction of flight, when the control of the right lever when the stop this function

Note: This feature can only be done automatically and the flight can not be reached automatically.

Speed selection

Speed file is to advance, back and left and right side of the flight is divided into third gear speed, the remote control is turned on by default when the slow power, press the remote control button issued a “flute” “flute” twice as midfielder, “flute” “” Flute “press three times for the fast file,” flute “soon return to slow file. (Recommended beginners with slow operation)

One Key Calibration

Place the drone on the horizontal plane,press one key calibration to automatically correct the drone

Aircraft settings reset

When a novice operates this remote control aircraft, if the flight is unstable after takeoff and drifts rapidly in one direction, the gyroscope level correction function can be used to correct the aircraft. Method As shown in the figure, the aircraft is placed on the flat ground after the start-up frequency is completed, and The throttle lever and the directional lever are simultaneously angled to the bottom right corner, the buzzer emits a “drop” sound, and the aircraft lights shine long, indicating that the horizontal correction is completed.

Emergency shutdown

1. If there is danger during the flight, you need to stop the emergency can be shown as shown, long press the roll button, the aircraft immediately stop running. This function does not attempt to operate when the aircraft is flyinig at normal altitude, and the non-side aircraft will fall quickly.
2. When the aircraft tilts more than 45 degrees, the aircraft will automatically stop protection.
3. When operating with APP, pull down the throttle and press a key stop button at the same time that is an emergency stop
   

Problem guide

Connect the flying saucerbatteries and flyThe indicator light on the dish continues Flicker, operation no response| Remote control and UFO is not successful| Please re-perform the remote control and the fiying saucer
Connect the flying saucer battery. There’s nothing wrong  with the orbiter should|

1. Check if the remote control and the flying saucer are powered on
2. Check whether the remote control and the UFO battery are in a low power state
3. Is the battery positive and negative

|

1. Turn on the remote control and insert the UFO battery.
2. Use full charge Full battery
3. Reinsert the battery and confirm that the battery and battery are positive or negative Pole piece of contact is normal.

Push the throttle lever. The motor does not turn and flies The indicator light on the disc starts flashing| UFO lithium battery power shortage| [Charge the battery or replace another fully charged battery
The tying saucer main rotor continues Tum but cannot take off|

1. The main rotor deformation
2. UFO battery power shortage

| Replace the main rotor2. Charge or replace the battery with another battery
The flying saucer vibrates badly| Main rotor deformation|

1. Replace the main rotor

The flying saucer will still go on or on After moving| The gyroscope is not at all right| The remote control can be automatically corrected mode, or restart the re-frequency
The flying saucer fell behind and lost flat On the fly.| The gyroscope s not at all right| The remote control can be automatically corrected mode, or restart the re-frequency

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>