bonoch BBM04 Long Range Video Baby Monitor User Manual
- June 11, 2024
- bonoch
Table of Contents
bonoch BBM04 Long Range Video Baby Monitor
We will update the manual frequently, you can scan the QR code or visit the website to get the latest version of the manual.
Overview
Packing List
-
Parent Unit x 1
-
Baby Unit (Camera) x 1
-
USB C Cable x 2
-
USB Chargerx 2
-
Set Screwx2
-
Wide-Angle Len x 1
-
Positioning Card
-
User Manual x 1
Baby Unit
-
Light Sensor
-
Standard Camera
-
Microphone
-
Pairing Button
-
TF Slot
-
Reset Hole
-
USB-C Charging Port
-
Antenna
-
Temperature Sensor
-
Power Switch
Parent Unit
- Display
- Power Button
- Volume
- Volume Level Indicator
- Power Indicator
- Menu/Back/Camera/Video Recording
- Zoom
- Up Arrow Key
- Left Arrow Key
- OK Button
- Right Arrow Key
- Down Arrow Key
- Play Music
- Intercom
- Microphone
- Antenna
- Speaker
- USB-C Charging Port
- Reset Hole
Getting Started
Step 1.
Connect the AC power adapter with camera. Plug the AC power adapter into power
socket.
Step 2.
Press for two seconds to turn on the parent unit.
Notes: The two units has already been paired in factory settings, so no repeated operation is needed in most cases. But if the auto pairing failed or you want to add more cameras, please try step 3 and step 4.
Step 3.
Set the parent unit to prepare for connecting.
Step 4.
Long Press PAIR button for five seconds until you hear the prompt tone.
Camera Placement ( on the wall )
Step 1. Put the camera at the pre-installation angle, then viewing from the display monitor, check if the angle is OK Using positioning card included, punch two holes horizontally apart with the same separation as the installation holes at the bottom of the camera.
Step 2. Push the matching anchors into the holes. Screw on with a screwdriver, leaving 1cm of the screw outside of the hole.
Step 3. Align the camera with the protruding screw, press and hold it down.
Function Operation
Switching Camera
Switch cameras manually
When two or more cameras ore connected. Press the “OK” button to enter the split screen mode. You can now use the arrow keys to select a screen you want to zoom in, and press the “OK” button again to switch to the new camera screen.
Turn on multiple cameras scan mode
When two or more cameras are connected, When the screen displays a single camera at the same time press the “OK” button for 3 seconds, “Scan mode on” displays at the bottom left of the screen, and the loop logo of the camera appears at the top of the screen. The baby monitor will automatically loop real- time video from up to 4 cameras in single-screen mode every 15 seconds or in split-screen mode every 30 seconds.
Turn off multiple cameras scan mode
To turn off multiple cameras scan mode, press the “OK” button for 3 seconds, the loop logo of the camera at the top of the screen will disappear.
Replacing the Camera Len
Rotate to remove the decorative ring of the original lens (please keep the removed decorative ring properly, it needs to be reinstalled later when using the standard lens)
Take out the additional wide-angle lens, align it and screw it ln, pay attention to make sure it is installed in place.
Note: After installation, remove the lens protection cover for normal use
Maintenance and Warranty
Maintenance
All of the following maintenance procedures should only be performed when baby
and parent units are unplugged and turned off.
Clean the surfaces of the baby and parent units with a soft, fluff-free cloth.
Never use cleaning agents or solvents.
If the units become dirty, use a slightly damp cloth to wipe surfaces. Take
care not to allow water into any openings.
Warranty terms
This baby monitor comes with a one-year warranty (replace or refund) and
lifetime technical support. The warranty terms do not apply to any product
that has been subject to abuse, misuse, negligence, or accident.
If you have warranty or support issues, please contact the customer service of
Amazon seller before leaving your review.
Information on Product Disposal
Always dispose of your product (with a non-removable pre-installed battery) at the end of its life in an environmentally responsible way and in accordance with your local waste disposal requirements. All cardboard and paper packaging materials should be recycled in accordance with your local council waste regulations.
Warning and Safety Instructions
Follow these safety precautions to prevent fire, injury, or damage to the product and your baby. Read and keep instructions handy: It’s very important to read all the safety and operation instructions before use.
Warnings
Troubleshooting
No signal on the Parent Unit
The power adapters may not be properly connected.
Confirm the toggle switch of the Baby Unit is in “Power On” position
Confirm the Parent Unit has power and is powered on
Ensure the Baby Unit and Parent Unit are not for from each other.
The baby Unit and Parent Unit may not be properly paired. Follow the PAIRING
instructions
Interference or poor connection
Opening the folded antenna upright improves signal reception
Move the Baby Unit closer to the Parent Unit.
The Baby or Parent Units may be too close to metal objects.
Other electronic devices may be interfering with the signal.
Maybe on a low battery.
Image frozen on the Parent Unit
Restart the Baby Unit (pull out the power adapter from the wall outlet, wait for approximately 5 seconds, and plug it back in) Reset the Parent unit by opening the battery compartment and disconnecting the battery. Wait for 30 seconds and then reconnect the battery.
A high pitched piercing noise is heard from the units (feedback, static)
The Baby Unit and Parent Unit may be too close to each other. Move them
further apart
The volume on the Parent Unit may be set too high.
Cannot hear the baby sounds on the Parent Unit
Volume setting on the Parent Unit may be too low. Increase the volume.
Background noise
In a quiet environment surrounding the Parent Unit, decrease the volume on the
Parent Unit to level 3 or below.
In a loud environment surrounding the Parent Unit, increase the volume on your
Parent Unit to its maximum level.
If the above tips do not help, the system may crash. Please disconnect the
battery and power adapter from your unit.
Then plug it in again and turn on your unit.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>