CARBEST 82507 Power Solar Panel 135 Instruction Manual

CARBEST 82507 Power Solar Panel 135

WARRANTY

The warranty period is 36 months. Reimo reserves the right to rectify eventual defaults. The guarantee is excluded for all damages caused by faulty use or improper handling. Liability limitations: In no case Reimo will be reliable for collateral-, secondary- or indirect damages, costs, expenditure, missed benefits or missed earnings. The indicated sales price of the product represents the equivalent value of Remo’s liability limitations..

DISPOSAL

Do not dispose of electrical appliances as unsorted municipal waste, use separate collection facilities. Contact your local government for information regarding the collection systems available. If electrical appliances are disposed of in landfills or dumps, hazardous substances can leak into the groundwater and get into the food chain, damaging your health and well-being. When replacing old appliances with new ones, the retailer is legally obligated to take back your old appliance for disposal at least free of charge

POWER SOLAR PANEL 135

• Foldable solar panel
• 135 W Power
• Preassembled solar charge controller on the back with integrated USB port (5 V/1,2 A)
• 4 m connection cable
• Including 3 adapters with 1 m connection cable each: alligator clips, Cigarette lighter cable, power plug
• Mobile charging of your 12 V battery
• 10 A charge controller integrated
• Foldable feet
• Integrated bag

INSTALLATION INSTRUCTIONS

1. Unfold the three panels outward. Extend the support legs.

2. Fully extend battery leads and connect the battery clips to the + positive (red) & – negative (black) battery terminals on a 12 V battery. Ensure that the connections are secure.
   NOTE |The kit should be connected to a battery generating at least 8 V to start the solar controller. If your 12 V battery is fully discharged, charge it for a short period of time by other means to reach 8 V.

3. When you connect the kit to the battery, the LCD display on the solar controller will turn on automatically.

Please read the following information about the solar charge controller LS1012EU carefully before you connect the battery clips to the battery terminals of your 12 V battery.

SAFETY INFORMATIONS SOLAR CHARGE CONTROLLER LS1012EU

• Read all of the instructions in the manual before installation.
• DO NOT disassemble or attempt to repair the controller.
• Power connections must remain tight to avoid excessive heating from a loose connection.
• Only charge batteries that comply with the parameters of controller.
• Risk of electric shock, the PV and load can produce high voltages when the controller is working.

OVERVIEW

The LS1012EU controller is a PWM charge controller with USB output that adopts the most advanced digital technique. It’s an easy operation and cost efficient controller featured as:

• 3-Stage intelligent PWM charging: Bulk, Boost/Equalize, Float
• Support 3 charging options: Sealed, Gel, and Flooded
• Battery status LED indicator can indicates battery situation
• Battery temperature compensation function
• With humanized settings, operation will be more comfortable and convenient
• The USB will provide power supply that can charge for electronic equipment (LSE series only)
• Battery type and load output can be set via button
• Extensive Electronic protection

PRODUCT FEATURES

LED INDICATORS

Charging status

| ****

Green

| ****

On solid

| PV connection normal but low voltage (irra- diance) from PV, no charging

Green

| ****

OFF

| No PV voltage (night time) or PV connection problem
Green| Slowly Flashing| In charging
 | Green| Fast flashing| PV over voltage

Load status

| Green| On solid| Load ON
Green| OFF| Load OFF
Green| Slowly flashing| Load over load
Green| Fast Flashing| Load short circuit
Battery status| LED 1| LED 2| LED 3| LED 4| Battery status
---|---|---|---|---|---
 | Slowly flas- hing| –| –| –| Under voltage
 | fast flashing| –| –| –| Over Discharge
Status during voltage is up| ON| ON| –| –| 12.8 V<Ubat<13.4 V
---|---|---|---|---|---
ON| ON| ON| –| 13.4 V<Ubat<14.1 V
ON| ON| ON| ON| 14.1 V<Ubat
 |  |  |  |  |
Status during voltage is down| ON| ON| ON| –| 12.8 V<Ubat<13.4 V
ON| ON| –| –| 12.4 V<Ubat<12.8 V
ON| –| –| –| Ubat <12.4 V

NOTE Voltage value for 12 V System at 25°C.

SETTING OPERATION

Load ON/OFF Setting
When the controller is powered on, press the button to control the load output.

Battery Type Setting

• Step 1: Enter setting mode by pressing the button for 5s until the battery status LEDs are flashing.
• Step 2: Select the desired mode by pressing the button.
• Step 3: The mode will be saved automatically without any operation for 5S and the LED will stop flashing.

PROTECTION

Battery Over Voltage Protection
When the battery voltage reaches to the set point of Over Voltage Disconnect Voltage (OVD), the controller will stop charging the battery to protect the battery from being overcharged to break down.

Battery Over Discharge Protection
When the battery voltage reaches to the set point of Low Voltage Disconnect Voltage (LVD), the controller will stop discharging the battery to protect the battery from being over-discharged.

Load Overload Protection
When the load is overloading (The overload current is ≥1.02 times, 1.05 times, 1.25 times, 1.35 times, 1.5 times the rated load current), the controller will automatically cut off the output after 50s, 30s, 10s, 2s and 0.5s. User has to reduce load appliance, then press the button or repower the controller.

Load Short Circuit Protection
The load will be switched off when a load short circuit happens. The user has to clear the short circuit, then press the button or repower the controller.

High Voltage Transient Protection
The controller is protected against small high-voltage transients. In lightning prone areas, additional external suppression is recommended.

TROUBLESHOOTING

LED Charging indicator turn off during daytime when sunshine falls on PV modules properly| PV array disconnection| Confirm that PV and battery wire connections are correct and tight.
No LED indicator| Battery voltage maybe less than 8V| Measure battery voltage with the multi-meter. Min. 8 V can start up the controller.
Charging status LED indi- cator fast flashing| Battery over voltage| Check if battery voltage is higher than OVD, and disconnect the PV.
LED 1 Fast flashing| Battery over discharged| When the battery voltage is res- tored to or above LVR point (low voltage reconnect voltage), the load will recover.
Load status LED indica- tor slowly flashing| Load over load 1| 1 Please reduce the number of electric equipments. 2 Press the button or repower the controller.
Load status LED indica- tor fast flashing| Load short circuit| 1 Check carefully loads connec- tion, clear the fault. 2 Press the button or repower the controller.
1 The overload current is ≥1.02 times, 1.05 times, 1.25 times, 1.35 times, 1.5 times the rated load current, the controller will automatically cut off the output after 50s, 30s, 10s, 2s and 0.5s.

TECHNICAL SPECIFICATIONS

REIMO REISEMOBIL-CENTER GMBH 63329 EGELSBACH · BOSCHRING 10 GERMANY · WWW.REIMO.COM
MADE IN CHINA

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>