CARBEST 671000 Cassette Toilet Instruction Manual

Cassette Toilet
671000

USER’S INSTRUCTION

Accessories list

Installations dimensions

• Please read this user manual carefully before you use the product and save it for future reference.

Safety instructions

Please read this manual carefully before installation and install it in strict accordance with this manual. After reading, please keep this manual properly.
In order to avoid injury or property damage to users and others, please strictly observe the safety warn-ings and cautions.

• Symbols and meanings
  | Warning! Risk o f  causing serious injury or damage.
  ---|---
  | Caution! Not f o l l o w  instruction will lead to damage.
  | This symbol indicates t h a t  t h i s  operation i s  forbidden.
  | This symbol indicates related information.

Warning

1. A lighted cigarette or other incendiary object must not be put into the toilet or it may cause a fire.
2. It is strictly prohibited t o disassemble, repair or modify the product, otherwise it may cause personal injury or fire.
3. The product must be connected to DC12V electricity and the positive and negative poles of the electricity should be properly connected. Otherwise, the product may be damaged or cause a fire.

Caution

1. The seat and cover of this product have the function of slow down. Do not press hard to avoid damaging the decelerator.
2. When using this product, do not lean back on the cover to avoid damaging the product.
3. Do not pour newspaper, paper urinal pad, sanitary towel and the other clogging articles into the toilet.
4. Do not stand on the seat, cover or toilet.
5. Do not use the toilet below 0 °C. If the indoor temperature i s lower than 0 °C, make sure you completely drain the waste-holding tank, t o prevent it from expanding and freezing.
6. Make sure you cut off the electricity and close the water system of the vehicle during installation, disassembly and maintenance.
7. lf you are not going to use this product for an extended period time, ensure t h a t the power supply is off and drain the waste-holding tank.
8. Children shall not play with t h i s product.

Main components

Toilet

1. Cover

2. Console

3. Control panel

4. Toilet cover

5. Toilet seat

6. Swiveling toilet bow!

7. B l a d e handle

8. Bottom base
   Waste-holding tank
   

9. Automatic pressure release vent

10. Gasket

11. Vent button

12. Pull handle

13. Wheel

14. Tank

15. Blade opener

16. Sliding cover

17. Drain spout

18. Cap

Before use

• Ensure that all packaging materials have been removed.
  1. Remove the waste-holding tank through the service door.
  2. Place the waste-holding tank upright and turn the pour out spout upwards. Remove the cap from the drain spout.
  3. Add the stated dosage cleaner t o the waste-holding tank, and add 2L o f water to the waste-holding tank t o ensure that the bottom of the waste- holding tank is covered.
  4.Screw the cap back onto the tank back into its original position via the service door.
  

Never add toilet cleaner directly via the valve blade or via the toilet bowl as this could damage the gasket ring of the waste- holding tank. Only fill the waste-holding tank via the drain spout.

Never use force if you cannot get the waste-holding tank back into place easily. If blockage occurs, always check if the blade handle is in the closed position.

Control panel logo & indicator

| Flush button: Press and hold it to  flush the toilet. Release it to  stop flushing.
---|---
| Light off: Indicates  the holding tank  is  not full and it  can be used normally.
Flashing red light: Indicates  the holding tank is full ,  need to  empty it on time.
| Light off: Indicates  the holding tank is in place and the blade handle is in the closed position.
Meaning the toilet is closed.
Solid green light: The blade handle is  in the open position. Meaning the toilet is open.
Flashing red light: The holding tank is removed or not in place. Meaning the toilet cannot be used.

Toilet Use

1. If you want to rotate the bowl to the desired position (max. 90° clockwise and 90° counterclockwise), use both hands t o rotate the bowl.
2. Open the blade by moving the blade hand lever from right to left (Righthand light on the control panel indicates green light).
3. Opening the Cover.

The toilet can be used with the blade open or closed.
The toilet can withstand a maximum load of 125kg. Make sure you do not overload the toilet.

Flushing the toilet:

1. Make sure the blade is open (Righthand light on the control panel indicates green light).
2. Press the flush button and hold it for several seconds to flush the toilet.

To prevent water leaking damaging your caravan, do not travel with water in the toilet bowl.
Close the blade if the toilet is not being used. Do not leave water in the toilet bowl .

Emptying the waste-holding tank

The waste-holding tank has liquid level indicator and a capacity alarm. When the left light o n the control panel blinks red, you will hear a series o f beeps by pressing the f l u s h i n g button. It means the waste holding tank is too full and must be emptied. When  the alarm sound appears, the flushing button will stop after 5s delay. (If less than 5s, can be used up to 2 times).

Emptying the waste-holding tank:

• If you want to continue using your toilet after emptying the waste-holding tank, prepare the waste- holding tank again. See Before use .

To prevent water leaking damaging your caravan, do not travel with a waste- holding tank that is more than 3/4 full.

Maintenance and cleaning

1. We recommend cleaning the toilet regularly to prevent scale.
   • Please wipe the dirty are a with a wrung-out soft cloth.
   Never use household cleaners to clean the toilet. These may cause permanent damage to the gasket and the other components.
   The blade gasket is apar to f the toilet that is subjected to wear.
   Depending on the extent and manner of servicing, afte racertain period the gasket will degrade and must be replaced.

2. We recommend t o remove the cover regularly to clean the dead corner.
   • Press the button at the back of cover.
   • Lift the cover and seat.
   • Gently push forward to remove the cover.
   • Installation after removal: Align the cover with the fixed plate and insert it to complete installation.

Winter use

1. The toilet seat can be used even in cold weather as long as it is placed in a heated area.
2. lf there is no heating and there is a risk of frost, we recommend against using the toilet.
   If the indoor temperature is lower than 0 °C, be sure to complete the drain of the toilet and RV water system.
   Then empty the waste-holding tank, t o prevent i t from expanding and freezing .

When this product is left unused

1. Empty the water system of the vehicle.
2. Press and hold the flush button of the toilet until no water rushes o u t .
3. Empty and dry the waste-holding tank.
4. Rinse and dry the entire toilet thoroughly.
5. Slide the waste-holding tank back into its original position and close the blade.

Technical specifications

Installation

1. Install the service door (Use Carbest service door).
   • Create the wall cut-out for the service door. Use the template with drawings a s the correct reference for the cut-out dimensions ( The wall thickness needs to be between 23mm and 39mm for the service door}.
   • Install the service door. For further information, see the installation instructions o f the service door.

2. Make sure that the toilet dimensions below, fit t o the shower tray before installation
   

3. Mount the wall bracket to the outside wall with three screws ST4.2*13mm, connecting the toilet to the wall bracket.
   Recommended distance between the wall bracket screws and the installation floor: 518mm
   (The actual installation may need t o adjust the position appropriately).

4. Mount the toilet to the floor with four screws ST4.5*55mm.
   Required torque (for a plywood oor): 1.2+0.3N.m.
   Torque may differ if the floor is made from a different material.

5. Connecting the water hose to the water system of the car.
   Length from the last fixed point: 300mmDiameter| Inside: 10mm| Outside: 16.5 mm
   ---|---|---
   Required presure| Min.:0.35bar at4.2L/min
   Max.:0.70bar at 7.1L/min
   Maximum allowable pressure| 8bar

Make sure after the hose is connected, the waste-holding tank can still be pulled out of the toilet seat and removed.

6. Adjust flush pressure (if applicable ) . Meet the required pressure for the remote pump at the toilet inlet to ensure correct flush. If the pressure is too high, use a slotted screwdriver to adjust the “water pressure control” knob on the solenoid valve.
   

Connecting electricity

1. Length o f main cord is 120mm.
   

2. Use the following parameters to connect the power supply correctly, otherwise the product may be damaged or cause a fire.

The red cable is positive. The black cable is negative .
Cable connections when the toilet is connected to  a non – pres – sure system|
The red cable is positive. The black cable is negative. The brown cable is positive. Connect the blue  cable to the positive connection of the pump.

The power supply specifications: 12V DC.

Install the vent hose & flange
At the desired location, drill 09mm diameter hole together with the vent joint on the ground and connect vent hose with two screws ST4.2*13mm .

2. Lift the clip, then pull out
Press the flush button but no flush-water| 1. When the waste-holding tank is full, the left light on the control panel blinks red
2. When the waste-holding tank is removed or not in place, the right light on the control panel blinks red
3. When the blade is closed, the light on the control panel is off
4. When the light on the control panel is off, indicates the toilet fuse is blown out| 1. Empty the waste-holding tank
2. Slide the waste-holding tank back in place
3. Move the blade handle to open the blade
4. Replace the toilet fuse
Waste-holding tank leaking| Gasket is dry or worn out| Replace gasket

In order to flush the valve, please turn the valve handle to make it open. After using, please turn the valve handle to close the valve. Do not use the toilet when the red light is flashing.
If you cannot solve the problem, contact the authorized local service center or REIMO Customer Ser-vice Office in your country.

Warranty:

The warranty period is 36 months. Reimo reserves the right to rectify eventual defaults. The guarantee is excluded for all damages caused by faulty use or improper handling. Liability limitations:
In no case Reimo will be reliable for collateral-, secondary- or indirect damages, costs, expenditure, missed benefits or missed earnings. The indicated sales price of the product is representing the equivalent value of Reimo’s liability limitations.

REIMO REISEMOBIL-CENTER GMBH
63329 EGELSBACH • BOSCHRING 10
GERMANY • WWW.REIMO.COM
MADE IN CHINA • © 02/2022

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>