TELEDYNE LECROY quantumdata 780 Series HDBaseT Remote Cable Tester Instruction Manual
- June 13, 2024
- TELEDYNE LECROY
Table of Contents
TELEDYNE LECROY quantumdata 780 Series HDBaseT Remote Cable Tester
Product Usage Instructions
- Connect the quantumdataTM 780 Series HDBaseT Remote Cable Tester to the near end of the network infrastructure cable using the 780C/D/E instrument.
- Connect the new 780 HDBaseT Remote Terminal to the far end of the network infrastructure cable.
- Run the cable test using the 780 instrument to verify the quality of the cable and its suitability for supporting video up to 300MHz (Ultra HD 4K at 30Hz or 60Hz with 4:2:0).
- If desired, use the optional 780 series Report File Creation feature to save the test results for record-keeping or dissemination to colleagues or contracting firms.
- To test network cable segments end-to-end, connect the network patch cables and run the cable test again.
- To test infrastructure cabling in segments and patch cabling separately, disconnect the network patch cables and run the cable test on each segment individually.
- Use the measurements provided in the user manual to interpret the test results for both the Main channel and Aux channel. The measurements indicate the quality of the channels at different frequencies.
- For Main channel quality, refer to the Mean Squared Error (MSE) and Maximum Errors (MaxErr) values. The color codes indicate the quality level – green (excellent), yellow (good), and red (poor).
- For Aux channel quality, refer to the Maximum Errors (MaxErr) values. The color codes indicate the quality level – green (excellent), yellow (good), and red (poor).
- The quantumdataTM 780 Series HDBaseT Remote Cable Tester is also compatible with HDBaseT converter devices and patch cabling. It can independently verify their quality at each end.
MEASUREMENTS / SPECIFICATIONS
Verify Installed HDBaseT Cable
- The network infrastructure cable is tested using the 780C/D/E instrument on the near end and the new 780 HDBaseT Remote Terminal on the far end as depicted (right).
- The remote cable test reports the quality of the cable and its suitability for supporting video up to 300MHz (Ultra HD 4K at 30Hz or 60Hz with 4:2:0). You can either test all network cable segments end-to-end or you can test the infrastructure cabling in segments and patch cabling separately.
- The optional 780 series Report File Creation feature can be used to save the results for record-keeping or dissemination to colleagues or contracting firms.
Measurement (Main Channel)
Main Channel
Mean Squared Error – MSE)
| Tests quality of the Main channel (per pair)
-20dB and greater: excellent up to 300MHz (green)
-15.5dB: good for 225MHz (yellow); acceptable for 300MHz (yellow)
-10dB: acceptable for 148.5MHz (yellow); poor for 225MHz (red)
---|---
Main Channel
Maximum Errors (MaxErr)
| 0-30: excellent (green)
31-55: good (yellow)
56-64: acceptable (yellow) greater than 64: poor (red)
Measurements (Aux Channel)
Aux Channel Errors Maximum Errors (MaxErr)
| Tests quality of the Aux Channel 0-30: excellent (green)
31-55: good (yellow)
56-64: acceptable (yellow) greater than 64: poor (red)
---|---
HDBaseT Remote Terminal Device (P/N 95-00146) (Specs – Functional)
HDBaseT – 780 Compatibility| HDBaseT 1.0; works with 780C, 780D, 780E
Instruments
---|---
Connector| (1) 8P8C (RJ-45) Rx; (1) HDMI Type A Hi-Speed Tx
Video Max Pixel Rate| 300 MHz; up to WUXGA, 4K Ultra HD (4K 30Hz or 4K 60Hz w/
4:2:0 pixel encoding)
Range| 70 meters over Cat5e/6/7
HDBaseT Remote Terminal Device (P/N 95-00146) (Specs – Mechanical/Power)
Power Adapter| 5V/1.2 amp DC Power Adapter; 5.5 W; AC input: 100-120 VAC,
47-63Hz
---|---
Weight| 0.5 LBS; 0.23 Kg
Size| Height: 0.88 in. (2.25 cm) Width: 2.2 in. (5.5 cm) Depth: 3.22 in. (8.2
cm)
Environmental| Operating Temp: 32 to 104 (F); 0 to 40 (C)
Measurement (Main Channel)
Main Channel
Mean Squared Error – MSE)
| Tests quality of the Main channel (per pair)
-20dB and greater: excellent up to 300MHz (green)
-15.5dB: good for 225MHz (yellow); acceptable for 300MHz (yellow)
-10dB: acceptable for 148.5MHz (yellow); poor for 225MHz (red)
---|---
Main Channel
Maximum Errors (MaxErr)
| 0-30: excellent (green)
31-55: good (yellow)
56-64: acceptable (yellow) greater than 64: poor (red)
Measurements (Aux Channel)
Aux Channel Errors Maximum Errors (MaxErr)
| Tests quality of the Aux Channel 0-30: excellent (green)
31-55: good (yellow)
56-64: acceptable (yellow) greater than 64: poor (red)
---|---
HDBaseT Remote Terminal Device (P/N 95-00146) (Specs – Functional)
HDBaseT – 780 Compatibility| HDBaseT 1.0; works with 780C, 780D, 780E
Instruments
---|---
Software| 780C, 780D, and 780E must have recent software, please contact
customer support
Connector| (1) 8P8C (RJ-45) Rx; (1) HDMI Type A Hi-Speed Tx
Video Max Pixel Rate| 300 MHz; up to WUXGA, 4K Ultra HD (4K 30Hz or 4K 60Hz w/
4:2:0 pixel encoding)
Range| 70 meters over Cat5e/6/7
HDBaseT Remote Terminal Device (P/N 95-00146) (Specs – Mechanical/Power)
Power Adapter| 5V/1.2 amp DC Power Adapter; 5.5 W; AC input: 100-120 VAC,
47-63Hz
---|---
LEDs| RJ-45 connector: Orange: blinking = no video detected (low power), solid
= video;
Green: blinking = HDCP off, solid = HDCP On
Weight| 0.5 LBS; 0.23 Kg
Size| Height: 0.88 in. (2.25 cm) Width: 2.2 in. (5.5 cm) Depth: 3.22 in. (8.2
cm)
Environmental| Operating Temp: 32 to 104 (F); 0 to 40 (C)
Key Features
- Verify Installed HDBaseT Network Cable – Test signal quality of the main video channel and auxiliary channel from the source end of HDBaseT network cable in a commercial or industrial building or office campus.
- Reduce Callbacks – Pre-qualify cable infrastructure for transmission of Ultra HD video prior to the final installation of the video source and display components.
- Verify patch cables and HDBaseT extenders – Run loop test on patch cables and extender devices at each end.
- Save Test Data Report – The solution can provide a report to record the results of the cabling infrastructure qualification. The reports can be saved onto an SD card for ease of preservation and dissemination to other colleagues.
Teledyne LeCroy quantumdata 780 series test instruments offer a rich set of
features that help professional A/V installers verify HDMI and HDBaseT video,
audio, and protocols. However, one of the problems facing professional video
integrators and installers is how to verify network HDBaseT cable
infrastructure in commercial, industrial, or institutional buildings or office
campuses intended to support HD and UHD video. This cable infrastructure is
often installed prior to the turn-up of the video sources and displays at the
endpoints.
The 780-based solution offered employs an HDBaseT Remote Terminal connected at
the far end of an HDBaseT network cable run with the 780C, 780D, or 780E
instrument at the source end. The 780 instrument can read the data from the
far end HDBaseT device to determine the quality of the network cable—main
channel and auxiliary channel—and its suitability for transmission of UHD
video. The 780 can also independently verify the HDBaseT converter devices and
patch cabling at each end.
1-800-909-7211 teledynelecroy.com
Local sales offices are located throughout the world. Visit our website to
find the most convenient location.
©2017 Teledyne LeCroy. All rights reserved. Specifications, prices,
availability, and delivery are subject to change without notice. Product or
brand names are trademarks or requested trademarks of their respective
holders.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>