EXPOLITE led22945 Fesnel LED WW Large User Manual

: June 13, 2024
: EXPOLITE

Table of Contents

EXPOLITE led22945 Fesnel LED WW Large
Product Information
Product Usage Instructions
Dimensions
Installation
Menu Map
Miscellaneous Settings
Using DMX512 Control
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

EXPOLITE led22945 Fesnel LED WW Large

Product Information

Product Name: FesnelLED WW Large
Model Number: led22945
Manufacturer: FOCON SHOWTECHNIC Vertriebsgesellschaft mbH
Power Supply: 100V – 240V AC 50/60Hz
Maximum Power Consumption: 180W
Dimensions: 417 x 286 x 260mm
Weight: 6.6kg
Power In/Out | DMX In/Out
Operating Temperature: –
Air Humidity: < 98%
Protection Class: IP 20
Aluminum Extrusion Profile
LEDs: Approximately 160W 3200K*
LED Driver Current: 3.0A
Beam Angle: –
Control: Stand-Alone / DMX512 / Dimmer
Voltage 100V – 240V AC 50/60Hz
Power Consumption 180W
Weight 6,6kg
Ambient Temperature -0°C – 45°C
Dimensions 417 x 286 x 260mm
Humidity < 98%
Protection IP 20
Housing Extruded Aluminium
LEDs ca. 160W 3200K*
LED Current 3,0A
Optics 15° – 60°
Control Stand-Alone / DMX512
DMX-Channels 1 – 5 (1/2/5)
Connectors Power In/Out | DMX In/Out

Tolerance in colour temperature according to LED manufacturer +/- 10%.

Product Usage Instructions

Delivery: Check the contents of the package to ensure all components are included.
Installation: Follow the installation instructions provided in section D-05 of the user manual.
Operation: Connect the product to the power supply and use the control options mentioned in section D-06 for standalone operation or DMX512 control.
Using DMX512 Controller: Set the DMX address and channel assignment as described in section D-08 of the user manual.
Various Settings: Adjust different settings using the menu options mentioned in section D-09 of the user manual.
Zoom Calibration: Perform zoom calibration using the menu option mentioned in section D-10 of the user manual.
Control with DMX512: Control the product using DMX512 protocol by following the instructions provided in section D-11 of the user manual.

Please refer to the complete user manual for detailed instructions and additional information.
The enclosed General Information for Expolite Units are part of these user manual. Read them carefully before operating the device.

Delivery

Expolite FresnelLED WW Large
Power connection cable
General Information for Expolite Units
User Manual

Expolite devices are carefully checked before shipment. If the delivery is not complete, please contact your distributor immediately.

Dimensions

Installation

Mounting
Hanging
The ﬁxture can be mounted in a hanging position using the mounting bracket. Fixture must be safe mounted in accordance with the relevant regulations and provided with a safetycord to prevent falling.

Standing
The ﬁxture can be mounted in an upright or sitting position. An appropriate attachment (e.g. ﬂoor stand) is necessary. A safe and suﬃcient anti-slip ground must be ensured!

NOTE
The LED module can be operated in any position.

Power connection
230V: max. 10 ﬁxtures in a row.
120V: max. 5 ﬁxtures in a row.

DMX-Connection
Use speciﬁed DMX-cables to connect the units to each other and to connect them to the control-desk. Enter the addresses and personalities to the units.

Operationinformation
This ﬁxture starts by default in „DMMR“ (Dimmer) operation mode. In this mode the access to all menus except for „RUNMODE“ are locked. If you change the operation mode to DMX or Slave, full access to all menus is given. To adjust the Zoom while operating via dimmerpack change the operation mode to „DMX“. Adjust the zoom value in the static menu. Than change the operation mode back to „DMMR“. The zoom value is stored and available even after power break.

Operation
Display Operation

Setting DMX-Address

The DMX start address of the ﬁxture is set in the menu ADDRESS. This is retained even when changing the personality.

Setting DMX-Personality

The personality is set in the menu SETTING, submenu PERSONALITY. There are three diﬀerent modes which can be choosen: UNO (1 channel), DOS (2 channels), STD.P (5 channels).

Editing Static Scene

A static scene for stand-alone operation can be set in STATIC. These are mixed using DIMMER and ZOOM.

Choosing Run Mode

The operating mode is set in menu RUN MODE. For operation on a DMX-controller DMX needs to be set. SLAVE sets the ﬁxture into slave mode.

Power Mode

In the menu POWER MODE the user can choose whether the ﬁxture is run with the power comparable to a 575W or 750W halogen lamp.

Reseting Zoom-Motor

In the menu MOTOR the zoom-motor of the ﬁxture can be reset (YES).

Miscellaneous Settings

The default password is: UP – DOWN – UP – DOWN – ENTER
KEY: activates or deactivates the password protection of the ﬁxture. If set ON the ﬁxture is password protected when started. 30 seconds after the last setting the menu is locked again. To be able to make changes in the menu the password UP – DOWN – UP – DOWN – ENTER needs to be typed in.
DIMMER: controls diﬀerent dimming speeds to simulate a halogen bulb (OFF/DIM1/DIM2/DIM3/DIM4).
CURV: In curve menu, the dimmercurves are set as shown below.

SLOCK: Settings Lock. In this menu is set whether the menu SET is only accesable after entering the password (ON) or without a password (OFF).
DMX ERROR: sets how the ﬁxture responses if DMX-signal gets lost. Set SAVE to hold the last received value or BLACK for blackout.
RESET: sets all editable settings back to factory default
ZOOM: in this menu the standard start position (POS1), end position (POS2) and the home position (BASE) of the motorised zoom are set.
PERFORMANCE: gives the user the opportunity to change the performance of the ﬁxture between LIVE, STUDIO and POWER.
MODE Setting: sets if the ﬁxture is a master and sends data to other ﬁxtures (MASTER), or not (SELF).
PWM: gives the user the possibility to adjust the PWM frequency of the leds (600Hz/1200Hz/2000Hz/ 4000Hz/6000Hz/25000Hz).

Zoom – Calibration

In the calibration menu (CALIBRATION), submenu CALZ the general minimum (POS1) and maximum position (POS2) of the motorised zoom can be set.

Info Menu

In the info menu (INFO), submenu VERS the currently installed ﬁrmware version is shown.

Using DMX512 Control

DMX-Channel assignment
This device has several DMX personalities. In each personality a diﬀerent number of DMX channels is used and the reaction of the device diﬀers accordingly. There are three DMX personalities with 1, 2 and 5 channels selectable. Because of changes in the ﬁrmware of the ﬁxture, functions can be added or changed. You can ﬁnd the current version „DMX-Channels“ as PDF-ﬁle on the website, ready to download.

UNO

1| 0-255| Master Dimmer
DOS

1| 0-255| Master Dimmer
2| 0-255| Master Dimmer Fine
STD.P

FOCON SHOWTECHNIC
Vertriebsgesellschaft mbH
Teichweg 4+6
D-49504 Lotte/Wersen
Telefon: ++49 (0) 541-77095-0
Fax: ++49 (0) 541-77095-27
info@focon-showtechnic.com
www.focon-showtechnic.com