EXPOLITE led29050 WD 600 Hybrid User Manual
- June 15, 2024
- EXPOLITE
Table of Contents
EXPOLITE led29050 WD 600 Hybrid
Specifications
- Voltage : 100V – 240V AC 50/60Hz
- Maximum Power Consumption: 400W
- Dimensions : 416 x 356 x 670mm
- Weight : 32kg
- Operating Temperature: –
- Air Humidity: < 80%
- Protection Class: IP 65
- LEDs : 1x 300W 7000K
- LED Driver Current: 5A
- Beam Angle : –
- Control : Stand-Alone / DMX512 / RDM / Artnet / sACN
Product Information
- Voltage: 100V – 240V AC 50/60Hz
- Power Consumption: 400W
- Dimensions: 416 x 356 x 670mm
- Weight: 32kg
- Connectors: Power In | DMX In/Out | ArtNet In/Out
- Ambient Temperature: -20°C – 45°C
- *Humidity:** < 80%
- Protection: IP 65
- Housing: Flame-retardend Plastic
- LEDs: 1x 300W 7000K**
- LED Current: 5A
- Optics: 3° – 30°
- Current: Stand-Alone / DMX512 / RDM /Artnet / sACN
- DMX-Channels: 21 – 29 (21/24/29)
Take note of General information for Expolite Units – Notes for Condensation inside Housing. Tolerance in color temperature according to LED manufacturer +/- 10%.
Dimensions
Installation **
**
Mounting
Hanging
The fixture can be mounted in a hanging position using the quicklock brackets.
Fixture must be safe mounted in accordance with the relevant regulations and
provided with a safetycord to prevent falling. For this purpose, an eyelet for
safeties is attached to the device.
Standing
The fixture can be mounted in an upright or sitting position. A safe and
sufficient anti-slip ground must be ensured!
NOTE
The LED module can be operated in any position.
DMX-Connection
Use specified DMX-cables to connect the units to each other and to connect them
to the control-desk. Enter the addresses and personalities to the units
.
Operation
Display Operation
- MENU: Return to the previous menu
- ENTER: Enter the currently selected menu
- UP: Scroll up, Increase value
- DOWN: Scroll down: Decrease value
- ROLL: Roll forward
Menu Map
Setting DMX-Address
The DMX start address of the fixture is set in the menu ADDRESS. This is
retained even when changing the personality.
Setting DMX-Personality
The personality is set in the menu PERSON. There are three different modes
which can be chosen: BASIC (20 channels), STANDARD (24 channels) and EXTEND
(28 channels).
Setting Runmode
- The operating mode is set in the menu RUNMODE.
- For operation on a DMX-controller DMX512 needs to be set.
- To control the fixture via ArtNet, the mode ARTNET needs to be set.
- In the mode ARTNET2DMX the chosen universe of the ArtNet input signal will be sent to the XLR- connectors.
- To control the unit via sACN the mode SACN needs to be set.
- To run an auto program choose AUTO.
In modes CUSTOM1 and CUSTOM2 it is possible to run a self created program. This is explained in Editing of user-defined programs. Custom programs are sent to connected slave fixtures. These signals are sent via the dmx-line. It may disturb other fixtures on the same dmx-line.
Miscellaneous Settings
- PAN INVERT: inverts PAN-movement.
- TILT INVERT: inverts TILT-movement.
- FANS: SLOW/NORMAL/FAST/AUTO regulates the fan performance balance.
- BLACKOUT: dims off the unit for Pan/Tilt movement.
- DIMMER: controls different dim curves to simulate a halogen bulb (DIM4/DIM3/DIM2/DIM1/OFF). LED-PWM: Sets PWM-frequency (1200Hz/2400Hz/4000Hz/6000Hz/25000Hz).
- DMX ERROR: sets how the fixture responses if DMX-signal gets lost. Set SAVE to hold the last received value or BLACK for blackout.
- DISPLAY ON: defines how long the display illumination stays active after the last input. You can set illumination time to SHORT or LONG.
- DISPLAY LOCK: locks (ON) or unlocks (OFF) display to prevent fixture from unauthorised access. Enter password to unlock display.
- LOAD PARA : This function sends user settings to all fixtures of the same type which are connected via dmx-cable to each other on the same dmx-line.
- SETTING\RECOVERY: sets all settings to factory default. To execute this function you need to enter a password.
- SETTING\CLEAN EDIT X: CLEAN EDIT 1 and CLEAN EDIT 2 deletes the self created scenes for CUSTOM1 and CUSTOM2.
- SETTING\WDMX HIDE : hides the WDMX settings in the menu (NO), or sets them visible again (YES).
- NETWORK\NET SWITCH: activates/deactivates the integrated ArtNet node.
- NETWORK\IP MODE : submenu for setting the ip-address. Users can choose between DEFAULT IP or CUSTOM IP. If set to CUSTOM IP the users needs to set a custom ip in the next step.
- NETWORK\CUSTOM IP EDIT: in this menu a user defined ip-address can be set.
- NETWORK\UNIVERS : the universe of the ArtNet node is set.
- PT ENCODER : Swaps channels for PAN and TILT.
- WDMX RESET : Unlinks the existing connection and enables the pairing with another transmitter.
- SIGNAL : In this menu the user can how the fixture is controlled:
- if the fixture is controlled via dmx-cable (ONLY XLRDMX).
- if signal on XLR connectors has higher priority than the WDMX signal (XLRDMX FIRST).
- if the fixture is controlled by WDMX signal (ONLY WDMX).
- if the WDMX signal has higher priority than the signal at the XLR connectors (WDMX FIRST).
- if WDMX signal is sent to the XLR connectors (WDMX TO XLRDMX).
PASSWORD : UP->DOWN->UP->DOWN->ENTER
Editing of user-defined programs
- In the menu EDIT, submenus EDIT1/2 two user-defined program can be edited.
- Each program can have up to 30 steps (STEP01 – STEP30).
- Every step persists of the parameter PAN, TILT, PT SPEED, CYAN (CMY_C), MAGENTA (CMY_M), YELLOW (CMY_Y), COLOR (wheel), Rotating Gobo (ROTA.GOBO), Gobo Rotation (GOBO.ROTA), FIXED GOBO, PRISM, FROST, ZOOM, FOCUS,
- DIMMER, STROBE, TIME and USE.
- In the submenu USE single steps can be set active (YES) or inactive (NO).
- User-defined programs can be transfered to other fixtures (see OPTION\LOAD PARA).
- Step-by-step programming of the custom stand-alone programs with up to 30 different steps.
NOTE : For less than 30 steps the TIME of the last step needs to be set to 0.
Example for time settings of a stand-alone program with 3 steps:
-
Step 1
TIME = 4 USE = YES -
Step 2
TIME = 5 USE = YES -
Step 3
TIME = 0 USE = YES
Auto-Test Menu
In the
menu MANUAL, submenu AUTO TEST the fixtures runs an auto test on all channels.
In the submenu CHANNEL single channels of the unit can be tested individually
over their whole DMX-range. The submenu DEBUG HIDE is the factory testmode.
All stepper motors can not be controlled via DMX when this mode is active.
This can only be changed after a reset of the fixture.
In RESET different parts of the fixture can be reset by the user individually:
- ALL RESET : runs a reset of all channels.
- PT RESET : runs a reset of the Pan-/Tilt-channels.
- COLOR SYS : runs a reset of the colour channels.
- GOBO SYST : runs a reset of the gobo channels.
- OTHER : runs a reset of the channels focus, zoom and prism.
Info-Menü
The following information can be checked in the info-menu:
- F IXTURE HOURS: Number of operating hours of the fixture.
- LED USE HOURS: Number of operating hours LED-unit.
- TEMPERATURE: Current temperature of the LED-unit.
- VERSION: the currently installed firmware version is shown.
- NETWORK PARA : shows the currently set network parameters.
- RDM : In the submenu UID the RMD-ID of the fixture is shown.
In the submenu LABEL the model name of the fixture can be found. In the submenu SYSTEM ERROR you can find the error message of the different sensors. It is differed in errors in light barriers (ENCODER), hall sensors (RESET) and other sensors (SENSOR).
Service-menu
(calibration of the fixture)
In this menu the different attributes of the
fixture can be calibrated.
NOTE : Improper settings in this menu can cause incorrect behavior of the fixture.
**Using DMX512 Controller
**
DMX-Channel assignment
This device has two DMX personalities. In each personality a different number
of DMX channels is used and the reaction of the device differs accordingly.
There are three DMX personalities with 20, 24 and 28 channels selectable.
Because of changes in the firmware of the fixture, functions can be added or
changed. You can find the current version „DMX-Channels“ as PDF-file on the
website, ready to download.
Basic
**Standard
Extend
Rotating Gobos**
Fixed Gobos
Frequently Asked Questions
How do I set the DMX address?
To set the DMX address, follow these steps:
- Navigate to MENU on the controller.
- Select PAEDRDSORENSS.
- Select H00S1IC-512.
How do I adjust the DMX channel assignment?
To adjust the DMX channel assignment, follow these steps:
- Navigate to MENU on the controller.
- Select PAEDRDSORENSS.
- Select BASIC STAHNSDICARD.
© 2021 by Focon Showtechnic Vertriebsgesellschaft mbH