Aqua Creek F-ADMRL-05 Admiral Pool Lift User Manual
- June 13, 2024
- Aqua Creek
Table of Contents
- MANDATORY
- Admiral Lift
- Admiral Components
- Installation: ADA Guidelines
- Anchor Installation: Core-Drill Retro-Fit
- Anchor Installation: Saw-Cut Retro-Fit
- Anchor Installation: New Construction
- Admiral Assembly Instructions
- Footrest Installation Instructions
- Pinch Point Locations
- Basic Troubleshooting
- Battery Test Cable Instructions
- Proper Care of Pool & Spa Lifts
- Admiral Parts List
- AQUA CREEK PRODUCTS, LLC LIMITED FIVE (5) YEAR WARRANTY:
- Documents / Resources
ADMIRAL
MAX WEIGHT CAPACITY: 450LBS [204kg]
U.S. PATENT NO. 7,249,386 B2 & D507,769 S
USE THIS MANUAL FOR PART #’s:
F-ADMRL / F-ADMRL-T / F-ADMRL-G
F-ADMRL-W / F-ADMRL-C
MANDATORY
LEAVE THIS MANUAL WITH OWNER
Read and follow all instructions.
Lift safety can only be ensured if the lift is installed and operated
according to these instructions.
- FOR SAFETY REASONS
- NEVER swim alone
- CERTIFIED
- NEVER use the lift with a dry pool
- NEVER apply direct water pressure to the electronics
- NEVER permit children to play on or around the lift
- DO NOT allow children to use the lift without adult supervision
READ CAREFULLY
Check entire box and all packing materials for parts. Before beginning
assembly, read the instructions and identify parts using the figures and parts
listed in this document.
It is critical that all parts be carefully inspected prior to installation. If
any damage occurred in transit, Aqua Creek Products, LLC must be notified
within three days of receipt of unit. Proper installation cannot be
overstressed, as an improper installation voids Aqua Creek’s warranty and may
affect the safety of the user.
Admiral Lift
IMPORTANT SAFETY INSTRUCTIONS
When installing and using this electrical appliance, basic precautions should
always be followed, including the following:
READ ALL INSTRUCTIONS BEFORE USING
WARNING – To reduce the risk of injury, do not permit children to use
this product unless they are closely supervised at all times.
This appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety. A wire
connector is provided on the unit to connect a minimum 8 AWG (8.4mm?) solid
copper conductor between this unit and the means for local equipotential
bonding.
Check the unit periodically for signs of deterioration: Keep all nuts, bolts
and screws tight to be sure the lift is in safe working condition.
SAVE THESE INSTRUCTIONS
Affix supplied ADA POOL/SPA LIFT sign in a location visible from the lift at
all times.
Rechargeable batteries are to be removed from the appliance before being
charged. Batteries are to be inserted with the correct polarity. If the
appliance is to be stored unused for a long period of time, the batteries
should be removed and stored on the wall mounted charger to maintain the
battery charge. The supply terminals are not to be short-circuited.
REDUCE THE RISK OF DROWNING!
Supervise children at all times.
No jumping or diving from the lift.
Seat may be hot, use caution when entering.
Keep covered when not in use. Inspect and clean before use.
INDOOR BATTERY CHARGER:
AMPERAGE = 0.65 FREQUENCY = 60
24 VOLT BATTERY
AMPERAGE = 8 IP RATING = IPX5
Admiral Components
- ADMIRAL LIFT MAIN ASSEMBLY
- 24V VITO BATTERY
- VITO CHARGER
- VITO HANDSET
- SAFETY BELT
- ANCHOR JIG PLATE (IF ORDERED WITH ANCHOR)
- ANCHOR INSERT BAG – SET OF 4 (IF ORDERED WITH ANCHOR)
- HARDWARE BAG (IF ORDERED WITH ANCHOR)
- VITO BATTERY TEST CABLE
Installation: ADA Guidelines
ADA REQUIREMENTS:
The Admiral Pool Lift is ADA Compliant.
The installation must meet the following requirements:
- Clear deck space dimensions (see FIGURE 1)
- Lift installed between 14.5-19 inches from the pool edge
- Deck slope no greater than 1:48
- The seat must submerge at least 18 inches into the water. The lift should be installed at a location with 42-48 inches of depth (deck to pool floor)
- Anchor setbacks are based on straight pool/spa walls. Curved pool/ spa walls will effect the anchor setback.
Anchor Installation: Core-Drill Retro-Fit
NOTE : FOR DECKS 6″ THICK OR MORE, 2500PSI MINIMUM STRENGTH CONCRETE
REQUIRED
You will need:
- Core drill and 172″ core drill bit
- Tape measure
- Marking pen
- Hammer
- Cold chisel
- Torpedo level
- High strength 2-part construction epoxy*
- Masking tape
- Black electrical tape (optional)
- Anti-seize packet
- Aqua Creek recommends either Hilti™ Brand HIT RE-500- SD or Simpson™ brand SET-XP or equivalent (not included)
-
Mark the 4 hole locations on your deck using the larger holes of the anchor jig plate as a template. For ADA compliance, confirm the center of the jig plate front holes are 14.5 to 19 inches from the pool’s edge. SEE FIGURE 2
-
Drill the 4 hole locations to 4 1/2 inches deep using the 1 1/2 inch drill bit. Clear all debris and ensure holes are completely dry.
NOTE: Create a depth marker on the drill bit with black electrical tape to make sure you drill to the right depth. NOTE: Local bonding regulations may require you to drill one hole larger than the others in order to bond at least one of the anchor inserts. You may need to saw cut a portion of your deck. See “Saw Cutting Retro-Fit Instructions” on page 6. -
Remove the nuts and the black protective coverings from the threaded anchor inserts.
-
Thread the mounting hardware through the smaller anchor jig plate holes and into the anchor inserts. Be sure to use anti-seize on the threads! Confirm the tops of the inserts are flush with the bottom of the plate.
NOTE: We recommend using masking tape around the holes on the bottom of the anchor jig plate to help prevent the anchor plate from being accidentally epoxied to the pool deck. -
Bond at least one of the anchor inserts according to your local code requirements. For more information see NEC Article 680.26.
-
Test fit the anchor inserts to make sure they line up properly. Place the anchor assembly into the pre-drilled holes and use atorpedo level to ensure your anchoring system is level.
-
Remove the anchor assembly and fill each hole halfway with 2-part construction epoxy.
-
Place the anchor assembly back into the holes. Wiggle the assembly as you reinsert it. Make sure the epoxy fully coats the threads.
-
Check that the anchor assembly is level.
-
Once the epoxy has set up, remove the hardware and the anchor jig plate. Your lift is now ready to be mounted to the anchoring system. The anchor jig plate may be recycled or used to install other anchors.
Anchor Installation: Saw-Cut Retro-Fit
You Will Need:
- Concrete saw with diamond blade
- Torpedo level
- Tape measure
- String Line
- 4’long straight edge or chalk line
- Concrete & concrete
- Sledge hammer finishing tools
- Cold chisel
-
5 rebar
- Remove 1 nut from each anchor insert. Place the anchor inserts through the larger hole of the anchor jig plate. Thread the removed nuts back onto the anchor inserts. The anchor plate should be sandwiched between the two nuts on each anchor insert. SEEFIGURE A
- Mark out a section of the pool deck that you are removing. Plan on removing at least 4 feet 0 inches by 4 feet 0 inches.
- Cut along your marks with a diamond blade concrete saw.
- Using the sledge hammer break up the concrete within the cut area and remove the pieces.
- Install rebar in the open area of the deck. Tie the rebar into the existing deck if possible. SEE FIGURE B
- Set the anchor system in place. For ADA compliance and clearance, make sure the center of the large anchor jig plate hole is between 14.5 and 19 inches from the pool’s edge. SEE FIGURE C, PAGE 7
- Using the string line or a straight edge, confirm the top of each anchor body is level with the FINISHED deck surface. Each anchor body can be individually adjusted by turning the nuts with a large wrench.
- Bond the anchoring system according to your local code requirements by using the bonding lug on the anchor plate. SEE FIGURE C, PAGE 7 (See NEC Article 680.26)
- Pour concrete and finish the pool deck surface. SEE FIGURE A
- Once the concrete has cured, the lift is ready to be mounted to the anchoring system.
Anchor Installation: New Construction
NOTE: For installations where a new deck is being poured, or where a
dedicated pad is being poured just for the pool lift, the concrete must
satisfy the ADA requirements outlined on page 3 of this manual.
Your pool deck must be at least 4 feet – 0 inches long by 4 feet – 0 inches
wide by 6 inches thick. It must be reinforced with 5 sticks of #5 rebar each
way, 2 inches clear (min) from the top and bottom of the footing.
-
Remove 1 nut from each anchor insert. Place the anchor inserts through the larger hole of the anchor jig plate. Thread the removed nuts back onto the anchor inserts. The anchor plate should be sandwiched between the two nuts on each anchor insert.
SEE FIGURE A, PAGE 6 -
Install rebar in the open area of the deck. SEE FIGURE B, PAGE 6
-
Setthe anchor system in place. For ADA compliance and clearance, make sure the center of the large anchor jig plate holes are between 14.5 and 19 inches from the pool’s edge. SEE FIGURE C
-
Make sure the top of each anchor body is flush with the FINISHED deck surface. Each anchor body can be adjusted individually by turning the nuts with a large wrench.
-
Bond the anchoring system by using the bonding lug on the anchor jig plate. Bond the system according to your local code requirements. (See NEC Article 680.26) SEEFIGUREC
-
Pour your concrete and finish the pool deck surface. SEE FIGURE A, PAGE 6
-
Once the concrete has cured the lift is ready to be mounted to the anchoring system.
Admiral Assembly Instructions
- Attach seat belt to the seat. SEE FIGURE D
- Install the Admiral pool lift onto the four (4) anchors using the supplied 1/2 inch x 1 1/2 inches stainless steel hex head bolts and 1/2 inch stainless steel washers. Make sure all bolts are tight before using the lift.
- Apply dielectric grease to the plug terminals, including the o-ring seal. Plug the handset cable into the large handset socket on the bottom of the control box. Press the cord end firmly into the socket until you are sure it is completely in the socket. Failure to fully push the remote cord into the socket may result in faulty or interrupted operation.
- Before installing the battery, place it on the charging unit and let it charge for 24 hours. Make sure the orange “charge” light illuminates when the battery is being charged. When the orange charge light shuts off, the battery is fully charged.
- Remove the fully charged battery from the charger and install it on top of the control box. The battery will line up with the control box, and will ‘click’when it properly locks in place. Apply dielectric grease to the plug terminals, including the o-ring seal, and then connect the battery cable to the control box cable.
- With the lift completely assembled, run the lift fully out and back in 3-5 times, without weight, for the lifts “break in” cycle period. WHEN NOT IN USE, STORE THE BATTERY ON THE CHARGER!
Footrest Installation Instructions
The Aqua Creek footrest assembly is designed to fit under the chair and is installed inside the 2” square tubing that supports the chair from underneath. To install the footrest;
- Insert the footrest assembly into the 2 x 2 square tubing that supports the chair until the plastic insert of the footrest assembly sits flush against the end of the 2 x 2 tube.
- Using the supplied 1/4” hardware, fasten the footrest assembly to the 2 x 2 tubing.
Pinch Point Locations
Field Reverse
To reverse the direction of the seat on the lift begin by removing the 1”7
jam nylock nut from the chair cradle. Then remove the 3/8” shoulder bolt,
flange bushing, sleeve bushing, flat washer and nylock nut the connects the
chair cradle assembly to the control arm. Next, remove the 1/4” button-head
bolt and flat washer connecting the control arm to the base of the lift. The
chair cradle assembly and control arm can now both be slid freely away from
the lift and “flipped” to the opposite side. Also, remove the 3/8” shoulder
bolt, 5/16″ flat washer and nylock nut connecting the actuator head to the
base of the lift. With the hardware removed, rotate the head of the actuator
180 degrees and then reinstall the hardware. Replace all components and
hardware in the reverse order of how it was uninstalled.
Basic Troubleshooting
Problem: rhe iift won’t move.
Solution:
- Make sure the cords are properly plugged in: Check the ends of the cords for corrosion or damage. The cord plugs should be recessed into the outlet. You should feel them pop into place when they are correctly inserted.
- Check the contact points: Make sure the contact point of the control box and the battery are not damaged or corroded. If there is corrosion clean with Scotch-Brite™ pad. Put some dielectric grease on the contact points before reattaching the battery
- Make sure the battery is fully charged: The Charger is ON when the green light is glowing
The Battery is CHARGING when the orange light is glowing
When the Battery is fully charged the orange light will stop glowing
Pr0blem: The lift stopped moving and is stuck.
Solution:
- Press the Emergency button Press the emergency retract button on the front of the control box to retract the lift.
Note: the lift will not retract if the battery is not fully charged or if the control box e is not working. The emergency button only overrides the remote handset.
For troubleshooting videos Visit:
www.aquacreek.com or scan the QR Code below
using your smartphone.
FOR TROUBLESHOOTING
http://aquacreekproducts.com/help-center/trouble-shooting/
Note: If you feel your lift is malfunctioning due to a faulty battery or connections, contact Aqua Creek Products for a testing kit.
Battery Test Cable Instructions
WARNING! DO NOT ATTEMPT TO DIRECTLY PROBE THE BATTERY CONNECTOR TO TEST
VOLTAGE.
THIS MAY CAUSE PERMANENT DAMAGE TO THE BATTERY! USE THE SUPPLIED BATTERY TEST
CABLE ONLY FOR CHECKING THE BATTERY VOLTAGE!
The Aqua Creek 24V battery has a cable and connector for connecting to the
control box or to the battery charger. The battery connector is not suitable
to check the battery voltage, as it is very hard to probe the connector
without shorting-out the battery, which will cause damage. For this reason, a
separate battery test cable is provided. To safely check the battery voltage,
use a voltmeter or multimeter with standard test probes, and insert the probes
into the test cable as shown below.
Proper Care of Pool & Spa Lifts
PROCEDURE | BEFORE EACH US | DAILY | WEEKLY | MONTHLY |
---|---|---|---|---|
Check battery level indicator on control box | ✓ |
Run the lift through a complete test cycle (fully extend actuator) to verify
it is functioning properly| ✓| | |
Wash lift with fresh water and dry with clean, soft, non-abrasive cloth| | ✓|
|
Recharge battery| | ✓| |
Visually inspect lift for damage, corrosion, and loose or missing hardware| |
✓| |
Check all contact points for damage and/or corrosion| | | ✓|
Repair, clean and apply dielectric grease to all contact points| | | ✓|
Thoroughly clean lift frame and apply a liberal coat of car wax to maintain
the lift’s finish| | | | ✓
Check all Warning and Cautionary labels to make sure they are not faded or
worn. Replace as needed.| | | | ✓
PROPER CARE NOTES
- Use only fresh water to wash your lift. Do not wash with pool water.
- Use only clean, soft, non-abrasive cloths on your lift.
- Do not store lift in pump room or near chemicals.
- Do not allow children to play on or around this lift.
- When cleaning the lift, do not spray water directly on control box or battery.
- The lift may need to be bonded according to local code requirements.
- If the lift is not used for extended periods, remove the battery from the lift and store it on the wall charger to maintain the batteries charge. The charger should be plugged in and in a climate controlled area.
STAIN REMOVAL TIPS:
To remove stubborn stains from finish, spray affected area with mild dish
soap, rub briskly with a 3M Scotch Brite™ pad. Use white epoxy paint to touch
up the finish. Apply wax to protect when dry.
For service and/or replacement parts, contact Aqua Creek Products
Toll free: 888-687-3552
Admiral Parts List
ITEM # | QTY | PART# | DESCRIPTION |
---|---|---|---|
1 | 1 | ADM-100-00 | BASE WELDMENT |
2 | 1 | ADM-200-00 | MAIN FRAME ASSEMBLY |
3 | 1 | ADM-300AWM-00 | ADJUSTABLE SEAT POLE |
4 | 1 | ADM-401-02 | CONTROL ARM |
5 | 1 | PF2-500-00 | BRACKET ASSEMBLY |
6 | 1 | REVWM-800-00 | CHAIR CRADLE |
7 | 1 | 340665-00 | LI NAK 400MM PULL ACTUATOR |
8 | 1 | F-0904CA-A | CHAIR ASSEMBLY |
9 | 1 | F-FRB-03 | FOOTREST ASSEMBLY |
10 | 1 | GT10 (CONTROL BRACKET) | VITO CONTROL BRACKET |
11 | 1 | VCB10 | VITO CONTROL BOX |
12 | 1 | VCP100-29800 | 24V VITO BATTERY |
13 | 2 | BSH 10 X 3/8 | 10-24 X 3/8 SHCS |
14 | 1 | BB 1/4 X 1/2 | 1/4-20 X 1/2 BHSCS |
15 | 1 | WF 1/4 | 1/4 FLAT WASHER |
16 | 1 | WL 1/4 | 1/4 LOCK WASHER |
17 | 1 | BH 5/16 X 4 1/2 | 5/16-18 X 4 1/2 HCS |
18 | 6 | WF 5/16 | 5/16 FLAT WASHER |
19 | 5 | NN 5/16 | 5/16-18 NYLOCK NUT |
20 | 1 | BS 3/8 X 9/16 | 3/8 X 9/16 SHOULDER BOLT |
21 | 1 | BS 3/8 X 1 3/4 18-8 | 3/8 X 1 3/4 SHOULDER BOLT |
22 | 2 | BS 3/8 X 2 18-8 | 3/8 X 2 SHOULDER BOLT |
23 | 2 | BC 3/8 X 3 | 3/8-16 X 3 FHSCS |
24 | 2 | WF 3/8 | 3/8 FLAT WASHER |
25 | 2 | NN 3/8 | 3/8 NYLOCK NUT |
26 | 1 | BH 5/8 X 5 7/8 18-8 | 5/8 X 5 7/8 HCS |
27 | 2 | WF 5/8 | 5/8 FLAT WASHER |
28 | 1 | NN 5/8 | 5/8 NYLOCK NUT |
29 | 1 | NNJ 1 | 1″ NYLOCK JAM |
30 | 1 | BRB EP060803 | 3/8 X 1/2 X 3/16 SLEEVE BUSHING |
31 | 1 | BRB SS-1216-4 | 3/8 X 1/2 X 1/4 BRONZE SLEEVE |
32 | 2 | BRB SS-1216-6 | 1/2 X 3/8 X 3/8 BRONZE SLEEVE |
33 | 1 | BRB FB-68-3 | 3/8 X 1/2 X 3/8 X 3/32 BRONZE FLANGE |
34 | 1 | F-UBC | BATTERY COVER |
Copyright © 2021 Aqua Creek Products All Rights Reserved
AQUA CREEK PRODUCTS, LLC LIMITED FIVE (5) YEAR WARRANTY:
ADMIRAL POOL LIFT
(ITEM #: F-ADMRL, F-ADMRLDD)
Aqua Creek Products, LLC (a.k.a. Aqua Creek) warrants to the original end
user purchaser that products manufactured by Aqua Creek, when properly
installed in accordance with assembly and installation instructions, and
properly used and maintained, shall be
free from defects in material and workmanship for a period of five (5) years
from the date of original purchase, provided that Aqua Creek receives prompt
notice in writing of any defect or failure and satisfactory proof thereof,
with the following exception(s):
Exceptions:
-
All electrical components, including the linear actuator shall have the following warranty period:
o Year 1-2: 100% Coverage
o Year 3: 60% Coverage (Customer is responsible for 40% of replacement cost)
o Year 4: 50% Coverage (Customer is responsible for 50% of replacement cost)
o Year 5: 40% Coverage (Customer is responsible for 60% of replacement cost) -
Hydraulic actuators and mesh slings shall have a warranty period of one (1) year from the date of original purchase.
-
Powder coat finish scratches, scrapes, corrosion, or dents from customers normal use, negligence, or abuse
This warranty specifically excludes reimbursement for labor to remove, repair,
or install the product and any shipping charges.
These warranties do not cover any damages due to accident, misuse, abuse,
negligence or failure to properly maintain any products, or normal wear and
tear from day to day operations. In the event that any products are altered,
repaired, or improperly installed or improperly used by anyone without the
prior written approval by Aqua Creek, all warranties are void.
IMPORTANT: AMOUNT OF WEIGHT PLACED ON LIFT SHALL NOT EXCEED THE RATED
LIFTING CAPACITY FOR THE LIFT. NEVER OPERATE THE LIFT UNDER LOAD IN A DRY POOL
(WITH NO WATER IN THE POOL). It is the responsibility of the lift owner to
verify the weight of the patron for warranty claim purposes and to ensure that
the lift is not overloaded. Non-payment for product to Aqua Creek may void
warranty. To initiate a warranty claim, the owner of an Aqua Creek product
must provide the place of purchase, in writing, with a full description of the
product, its serial number, the dates of purchase and installation, and the
exact nature of the defect. Within thirty (30) days after receipt of a written
warranty claim by Aqua Creek, and barring any unforeseen delays, the place of
purchase will be notified of Aqua Creek’s decision regarding the claim.
If requested by Aqua Creek, any defective product must be returned, freight
prepaid by customer, to Aqua Creek’s designated factory location or duly
appointed distributor for inspection and/or repair. Aqua Creek will, at its
option, repair or replace the failed or defective item, and deliver the
repaired product or replacement to the customer. All freight charges are the
responsibility of the customer. Products returned to Aqua Creek for which Aqua
Creek provides replacement under this limited warranty shall become the
property of Aqua Creek. A new warranty period shall NOT be established for the
repaired or replaced products. Such products shall remain under warranty only
for the remainder of the original warranty period on the original products
purchased.
This written limited warranty constitutes the final, complete and exclusive
statement of warranty terms. No person or organization is authorized to make
any other specific or implied warranties or representations on behalf of Aqua
Creek.
THE WARRANTIES SET FORTH HEREIN ARE IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED
OR IMPLIED, WHICH ARE HEREBY DISCLAIMED AND EXCLUDED, INCLUDING WITHOUT
LIMITATION ANY WARRANTY OF ERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE
OR USE.
THE SOLE AND EXCLUSIVE REMEDIES FOR BREACH OF ANY AND ALL WARRANTIES WITH
RESPECT TO THE PRODUCTS SHALL BE LIMITED TO REPAIR OR REPLACEMENT AT AQUA
CREEK’S DESIGNATED FACTORY LOCATION, OR DULY APPOINTED DISTRIBUTOR, OR IN
PLACE AT AQUA CREEK’S OPTION. IN NO EVENT SHALL AQUA CREEK’S LIABILITY EXCEED
THE ENTIRE AMOUNT PAID TO AQUA CREEK BY THE ORIGINAL PURCHASER FOR THE FAILED
OR DEFECTIVE PRODUCT. IN NO EVENT SHALL AQUA CREEK PRODUCTS, LLC BE LIABLE FOR
ANY INCIDENTAL, CONSEQUENTIAL, SPECIAL, INDIRECT, PUNITIVE OR EXEMPLARY
DAMAGES OR LOST PROFITS FROM ANY BREACH OF THIS LIMITED WARRANTY OR OTHERWISE.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER
RIGHTS, WHICH MAY VARY FROM STATE TO STATE. SOME STATES DO NOT ALLOW THE
EXCLUSION OR LIMITATION OF INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES, SO
SOME OF THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU.
Aqua Creek Products, LLC
9889 Garrymore Lane
Missoula, MT 59808
Toll Free:888-687-3552
Local/Intnl:406-549-0769
www.aquacreek.com
AQUACREEK.COM
Affordable ADA, Aquatic Exercise, Dock, and Beach Access PLUS Much More.
Copmgnt <o 200 { Agse Creek Proouets,
L LC. /8 10ghts ileasried.
Documents / Resources
| Aqua
Creek F-ADMRL-05 Admiral Pool
Lift
[pdf] User Manual
F-ADMRL-05 Admiral Pool Lift, F-ADMRL-05, Admiral Pool Lift, Pool Lift
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>