BLUE OX BX1735 Baseplate fits Select Chevrolet Blazer Instruction Manual

BLUE OX BX1735 Baseplate fits Select Chevrolet Blazer

Product Information

• Product Name: BX1735 Baseplate
• Compatible Vehicle: 2019-2022 Chevy Blazer (Includes RS, ACC, & Shutters)
• Attachment Tab Height: 13.5
• Attachment Tab Width: 20
• Serial Number: 405-0656 Rev A
• Manufacturer: Blue Ox

Product Usage Instructions

1. Before installing or operating the BX1735 Baseplate, make sure to read both the Installation Instructions and the General Information sheet provided.
2. Refer to the vehicle owner’s manual for the manufacturer’s towing specifications.
3. If your vehicle’s front looks different than what is shown in the instructions, contact Blue Ox at (402)385-3051 for assistance.
4. Ensure that all components that are removed during the installation process are placed on a flat and sturdy surface. These items will be reinstalled unless otherwise noted.
5. The dimensional variations between vehicles can be significant, so some adjustments may be required to tailor the baseplate to your vehicle manufacturer’s tolerances.
6. It is recommended to use the BX8848 Tail Light Wiring Kit for this vehicle.
7. To begin the installation:
8. Next to the tail light, pull on the black piece from the top to remove it on both sides of the vehicle.
9. Using a 7MM socket, remove the two (2) bolts attaching the tail light to the frame. Push the tail light sideways slightly to unsnap it and then pull it straight back on both sides of the vehicle.

Tools Required:

• Large Vise Grip
• Flat Screwdriver
• Utility Knife
• Reciprocating Saw
• Torque Wrench
• Drill
• T15 Torx

Parts List: Item No. | Part No. | Description | Qty. 1 | 61-4978 | 3/8-16 Whiz Nut w/ 14 Wire | 2 2 | 61-5208 | 3/8 Nut Plate w/ 14 Wire | 5 3 | 61-8205 | BX1735 Baseplate, DS | 1 4 | 61-8206 | BX1735 Baseplate, PS | 1 5 | 62-3469 | Attachment Tab Assembly with Hole | 2 Please note that the provided information is a partial extract from the user manual. For complete instructions and additional details, it is recommended to visit www.blueox.com for the latest version of the installation instructions.

BX1735 2019-2022 Chevy Blazer
(Includes RS, ACC, & Shutters) Installation Instructions

• Attachment Tab Height : 13.5”
• Attachment Tab Width : 20”

Installation Instructions

Please read BOTH these Installation Instructions and the General Information sheet prior to installing or operating this equipment.

1. Blue Ox® towing products and accessories are intended to be installed by Blue Ox® Dealers who are familiar with our products and have the equipment and knowledge necessary to do “fit work”. If needed, Blue Ox® Dealers can be found at www.blueox.com or by contacting our Technical Service Department at 402-385-3051.
2. Many Blue Ox® baseplates are designed to use existing holes and hardware to mount the baseplate to the towed vehicle. Even though bolts are there, do not assume they are adequate for baseplate mounting. Always use the hardware supplied in the hardware kit and existing hardware as specified in the installation instructions.

If the front of your vehicle looks different than this, please contact us at (402)385-3051.

Bolt Torque Specifications

Torque in Foot-Pounds for Inch Bolts

Bolt Torque Specifications
Torque in Foot-Pounds for Metric Bolts

Reference your vehicle owner’s manual for manufacturer’s towing specifications.

WARNING
Failure to read and follow these instructions could result in separation of the towed vehicle from the tow bar, causing property damage, loss of towed vehicle, personal injury or death.

BX1735 2019-2022 Chevy Blazer (Includes RS, ACC, & Shutters) Installation Instructions

• Instruction Notes: The fascia cover, fascia, and windshield washer fluid reservoir are removed and reinstalled for the baseplate installation. Some drilling and trimming is required.
• Place all components that are removed on a flat, sturdy surface. All items will be reinstalled unless otherwise noted after the baseplate is installed.
• The dimensional variations between otherwise identical vehicles can be considerable. While the baseplate was designed for easy installation, it may be necessary to tailor the baseplate slightly to compensate for vehicle manufacturer’s tolerances.
• The BX8848 Tail Light Wiring Kit is recommended for this vehicle.

1. Next to the tail light, pull on the black piece from the top to remove. Do this on both sides of the vehicle.
2. Using a 7MM socket, remove the two (2) bolts attaching the tail light to the frame. To remove, push tail light side ways slightly to unsnap and then pull straight back. Do this on both sides of the vehicle.

NOTICE

• Handling of some cosmetic parts when installing this product may require the use of protective covers, rags, specialty tools, etc. to prevent damage.
• When using power drills be aware of the dangers of torque and drill bit length.
• When using a reciprocating saw be aware of objects behind the cutting surface.
• Use a good quality paint to spray cut edges of frame to prevent rusting.
• Be sure that ALL electrical connections are plugged in and accessories are functioning properly before reinstalling the fascia.
• The baseplate is computer tested to your vehicle’s GVWR, exceeding this weight will void the manufacturer’s warranty.
• Be sure to use a sufficient amount of Loctite® Red on all bolt threads before tightening. Tighten all bolts according to the torque chart provided unless specified.
• Dealer or installer be certain the user receives these instruction sheets.
• If the baseplate is in an accident, it must be replaced. DO NOT use it again! An accident can cause unseen damage and using it again could result in more damage or serious injury.
• DO NOT use the baseplate if it is damaged or missing parts.

Tools Required

• Large Vise Grip
• Flat Screwdriver
• Utility Knife
• Reciprocating Saw
• Torque Wrench
• Drill
• Loctite® RED
• 3/8” Drill Bit
• 7MM Socet
• 10MM Socket
• 15MM Socket
• 7/16” Socket
• 7/16” Wrench
• 9/16” Socket
• 9/16” Wrench
• T15 Torx

Item No. Part No. Description Qty.

• 1……………………………61-4978…………………………3/8”-16 Whiz Nut w/ 14” Wire…………………………………….2
• 2……………………………61-5208…………………………3/8” Nut Plate w/ 14” Wire…………………………………………5
• 3……………………………61-8205…………………………BX1735 Baseplate, DS……………………………………………..1
• 4……………………………61-8206…………………………BX1735 Baseplate, PS……………………………………………..1
• 5……………………………62-3469…………………………Attachment Tab Assembly with Hole…………………………..2
• 6……………………………101-10248……………………..Spacer Plate……………………………………………………………1
• 7……………………………201-0050……………………….1/4”-20 x 3/4” Hex Head Bolt, Grade 5, ZP………………….1
• 8……………………………201-0192……………………….#10-32 1/2” Round Slotted Head Screw………………………2
• 9……………………………201-0440……………………….3/8”-16 x 1-1/2” Hex Head Bolt, Grade 5, ZP……………..13
• 10………………………….201-0553……………………….1/4”-20 x 1/2” Hex Washer Head, Type F TCS, ZP……….2
• 11 ………………………….201-0979……………………….#12-14 x 1” Self Drilling Screw, ZP……………………………..2
• 12………………………….202-0047……………………….#10-32 Hex Nut……………………………………………………….2
• 13………………………….202-0090……………………….3/8”-16 Hex Nylon Insert Lock Nut, ZP………………………..6
• 14………………………….202-0102……………………….1/4”-20 Hex Nylon Nut, ZP………………………………………..1
• 15………………………….203-0003……………………….3/8” Flat Washer, ZP……………………………………………….10
• 16………………………….203-0010……………………….3/8” Lock Washer, ZP……………………………………………..13
• 17………………………….203-0054……………………….#10 Lock Washer, ZP……………………………………………….2
• 18………………………….290-0275(not shown)………8” Nylon Cable Tie……………………………………………………2
• 19………………………….299-0685……………………….Electrical Bracket, ZP……………………………………………….1
• 20………………………….226-0049(not shown)………Class IV Safety Cables……………………………………………..2
• 21………………………….229-0512(not shown)………1/2” Quicklink, ZP…………………………………………………….2
• 22………………………….290-0437(not shown)………Black Cap Plug Receiver…………………………………………..2

Important:
Use only genuine factory replacement parts on your baseplate. Do NOT substitute homemade or non-typical parts. If a bolt is lost or in need of replacement, for your safety and the preservation of your baseplate, be sure to use a replacement bolt of the same grade (In most cases it will be Grade 5, please reference the parts list above). Replacement parts may be ordered through your nearest Blue Ox® Dealer or Distributor. Failing to follow and/or altering these installation instructions in either installation or required equipment will void the manufacturer’s warranty. Towing behind a non-motorized vehicle will void the warranty.

BX1735
2019-2022 Chevy Blazer (Includes RS, ACC, & Shutters)

Installation Instructions

1. Remove the twelve (12) push pins from the fascia cover, six (6) on each side. Set aside to be reinstalled later.

2. Using a T15 Torx, remove the six (6) bolts, three (3) on each side, from the top of the fascia.

3. Using a T15 Torx, remove the four (4) bolts from inside of the wheel well in front of the tire. Do this on both sides of the vehicle.

4. Unsnap the fender trim by pulling outward away from the fascia. Place a rag or soft item between the trim and fascia to hold trim out of the way and prevent damage to the fascia. Do this on both sides of the vehicle.

5. Using a T15 Torx, remove the one (1) bolt from the fascia joint under the fender trim. Do this on both sides of the vehicle.

6. Using a T15 Torx, remove the six (6) bolts from the underside of the vehicle in front of the tire. There are three (3) on each side.

7. Using a 7MM socket, remove the two (2) bolts from the underside of the vehicle in the center.

8. Pull back the wheel well liner. Using a 7MM socket, remove the three (3) bolts from behind the light. Do this on both sides of the vehicle.

9. Pull the fascia away from the vehicle to unsnap. Unplug all electrical connections, remove the fascia and set aside to be reinstalled later.

10. Using a 10MM socket, remove the four (4) bolts from the windshield washer fluid reservoir on the driver side of the vehicle. Disconnect all lines. Remove reservoir and set aside to be reinstalled later.

11. On the driver side of the vehicle use a reciprocating saw to trim the back of the Adaptive Cruise Control (ACC) bracket approximately 1/4 inch or more to allow clearance for the baseplate.

12. Using a 10MM socket, remove the three (3) bolts (white) on the underside of the vehicle holding the plastic shroud. Then using a 7MM socket, remove the two (2) bolts (gray) from above the shroud. Remove shroud and set aside to be reinstalled later.

13. Slide the passenger side plate onto the vehicle ensuring that it is as high as possible and as far forward as possible. Using a 3/8” drill bit, drill the two (2) bottom holes and start the two (2) 3/8” bolts with hardware.

14. Hold the driver side plate and cross bar in place. Where the cross bar attaches to the passenger side plate, start one (1) 3/8” bolt and hardware. Use a vise grip to hold the driver side plate in place.

15. Using a 3/8” drill bit, drill the remaining seven (7) holes, four (4) on the driver side and three (3) on the passenger side. Use the end plates as templates.

16. Install the four (4) 3/8” bolts with hardware on the driver side of the vehicle.
    Use Loctite® Red on all bolt threads and tighten all bolts to the appropriate torque.

17. Using a 15MM socket remove the two (2) bolts from the bumper to allow room to install the bolts on the passenger side plate. Set aside to be reinstalled later.

18. Start the three (3) remaining 3/8” bolts with hardware on the passenger side of the vehicle. Insert shim as shown and tighten all hardware. Reinstall the two (2) bumper bolts.
    Use Loctite® Red on all bolt threads and tighten all bolts to the appropriate torque.

19. Install the remaining three (3) 3/8” bolts with hardware attaching the cross member to the passenger side plate.
    Use Loctite® Red on all bolt threads and tighten all bolts to the appropriate torque.

20.  Attach the permanent baseplate safety cables to the provided convenience link on the baseplate. The photo above shows the recommended installation of the cables to frame of vehicle. Additional options may interfere with suggested mounting; in this case, secure the cables to a solid piece of the frame as described in the General Information sheet. Be sure the safety cables do not rub against any hoses or moving parts. Do this on BOTH sides of the vehicle.

21. Hold plastic shroud in place, mark, and trim as needed around baseplate before reinstalling.

22. Reinstall the windshield washer fluid reservoir on the driver side of the vehicle. Reconnect all lines.

23. Remove the temperature sensor from the bracket on the back side of the fascia. Using a reciprocating saw, cut the bracket as shown. Relocate temperature sensor, connecting it to upper loom using two (2) provided zip ties.

24. Optional: Install the breakaway to the bracket on the baseplate with one (1) 1/4” bolt with hardware.

25. Hold the fascia as close to its original position, mark and trim the fascia around the convenience links and attachment tabs. Reinstall the fascia and fascia cover. Reconnect all electrical connections.

CUSTOMER SERVICE COMMITMENT

• Blue Ox® is committed to providing you with exceptional customer care throughout your lifetime with our products. Our team is here to assist you with any questions you may have regarding the performance of your product. Simply call 402-385-3051 and you can speak with our technical service team.
• Additionally, please visit our website to see which rallies our Destination America team will be attending. For a nominal fee, our service technician will service your towing system to ensure it’s in proper working condition. Also, as a commitment to our customers, should you visit our factory, you can stay at our full service Blue Ox® campground at no charge along with enjoying a factory tour.
• Again, thank you for being our customer and for the confidence you have shown in the performance of our products. It is because of customers like you we enjoy the success we have today.

General Information

1. Ensure that your product(s) are registered online at www.blueox.com . It is crucial to register your product(s) so that you may be alerted of product offerings, updates, upgrades, maintenance and safety bulletins, and/or recalls.
2. It is the owner’s responsibility to inspect all towing equipment for cracked welds, missing or worn parts and loose bolts before each towing trip. Be sure to use Loctite® Red on all bolts and tighten to the recommended specifications.
3. It is the owner’s responsibility to hook up all towing equipment per manufacturer’s instructions/recommendations.
4. Remove the attachment tabs when not in use (if applicable).

Notice To Baseplate Installer

1. It is YOUR responsibility to watch for:
2. Oil cooler and air conditioner lines
3. Electrical wires and hoses
4. Missing parts or attaching points on the frame

** If the baseplate is improperly installed and is against a wire or hose, it could cause fluid leaks or electrical shorts some time after the actual baseplate installation.

Permanent Baseplate Safety Cable Installation

• Permanent baseplate safety cables are strongly recommended when towing a vehicle with a tow bar. The principle function of the permanent baseplate safety cables is to prevent the towed vehicle from breaking loose in the event the connection between the frame of the towed vehicle and the baseplate fails or becomes disconnected. The cables must be connected from the baseplate to the frame rail or cross member of the vehicle’s frame. The illustrations below show the possible arrangements recommended by Blue Ox®. Each permanent baseplate safety cable must have an adequate weight rating for the towing system. The weight rating of the two (2) cables together will not qualify.
• Do not mount the permanent baseplate safety cables against wires, hoses or brake lines.
• These permanent baseplate safety cables should remain installed as long as the baseplate is installed on the vehicle. Permanent baseplate safety cables are to be used in conjunction with, and NOT a replacement for legally required safety cables attaching the towed vehicle to the towing vehicle.

BLUE OX ORIGINAL PURCHASERS

THREE YEAR LIMITED WARRANTY

• Automatic Equipment Manufacturing Company (“Automatic”) warrants to the original (first) retail purchaser that this product, manufactured by Automatic, shall be free from defect in material and workmanship under normal use and service for a period of three years from the date of delivery.
• During said three-year period, Automatic will repair or replace any parts that have been returned by the original purchaser, to the factory, transportation prepaid, and in Automatic’s sole and absolute opinion found to be defective.
• Limitations on Warranty Coverage:
  • Coverage under this warranty will be valid only if the customer warranty card is returned by the original purchaser within 30 days of purchase.
  • Coverage under this warranty will be effective only when a copy of the original invoice, showing date and place of purchase, accompanies any claim for warranty. This warranty is NON TRANSFERABLE.
• This limited warranty will not cover, in any way or form, any alleged damages caused by incorrect or improper installation, improper use, modification or neglect of product, failure to properly service and maintain, misuse, act of God, accident or failure of the user to follow guidelines contained in the instructional material provided by Automatic.
• This warranty does not cover normal wear and tear, paint or rust.
• Warrantor assumes no responsibility to the owner for loss of use of product, loss of time, inconvenience or any other damage consequential or otherwise. Including, but not limited to mileage, expense of transporting of product, return shipping expense, mechanics travel time, telephone, road service, towing, and rental during repairs, travel, lodging, loss or damage to personal property or loss of earnings.
• REPAIR OR REPLACEMENT AS SET FORTH IN THIS LIMITED WARRANTY IS THE SOLE EXCLUSIVE REMEDY OF THE PURCHASER. AUTOMATIC SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON THIS PRODUCT. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ON THIS PRODUCT IS LIMITED IN LENGTH TO THE DURATION OF THIS WARRANTY.
• Please visit http://blueox.com/warranty/ to register your warranty

© 2016 Blue Ox
One Mill Road, Industrial Park Pender, Nebraska 68047 Phone: 402-385-3051 Fax: 402-385-3360
www.blueox.com

References

• Blue Ox Product Warranty Registration - Blue Ox
• Home - Blue Ox

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>