ROUSENSMART RS-ECS IOT SDN Gateway Instruction Manual
- June 13, 2024
- ROUSENSMART
Table of Contents
ROUSENSMART RS-ECS IOT SDN Gateway
Product Information
The IOT SDN Gateway RS-ECS is a device designed to enable communication
between various devices in an Internet of Things (IoT) network. It operates on
a working voltage of 24 V DC and has a transmitted power of +20dBm. The device
has a receiving sensitivity of -103dBm and a transmission rate of 250kbps. It
features a serial interface with one RS485 port and one RS232 port. The device
also includes a network interface with one RJ45 port.
The antenna gain of the device is 4.12dBi.
Product Usage Instructions
Connection:
Refer to the figure below for the connection mode of the IOT SDN Gateway
RS-ECS.
Installation:
Follow the steps below to install the IOT SDN Gateway RS-ECS:
- Attach the gateway to the backplane of the cabinet.
- Fix the gateway in place using screws.
- Ensure that the control cabinet has good tightness and convenient subsequent wiring arrangements.
- Place the control cabinet in an open, dry, and noncorrosive liquid place to avoid damaging the equipment.
Refer to the figure below for the installation mode of the IOT SDN Gateway RS- ECS.
FCC Warning
This device complies with part 15 of the FCC Rules. To ensure proper
operation, it must meet the following conditions:
- The device should not cause harmful interference.
- The device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not approved by the responsible party may void the user’s authority to operate the equipment. Consult the dealer or an experienced radio/TV technician for assistance if needed. To maintain compliance with FCC’s RF Exposure guidelines, ensure a minimum distance of 20cm between the radiator and your body. Use only the supplied antenna.
This product is a backbone and management device in the IOT area, which is used to connect the IOT and the upper backbone network. It is mainly used for unified management and deployment of IOT devices such as coordinators, couplers and controllers in the IOT gateway. It supports data upload, instruction delivery, online upgrade and parameter setting. It has the features of AD Hoc network, self-recovery from network disconnection, self- selection of optimal network path, self-rehabilitation from link failure, and supports hibernation and wake up. The product is made of aluminum alloy material, with waterproof and moisture-proof measures, so that it is suitable for the complex scene with harsh environment or strong interference, such as underground pipe gallery, tunnel, mine, factory, etc. The online upgrade function and parameter setting function make it possible for IOT devices to be updated quickly and easily. Wireless transmission and AD Hoc network can flexibly add sensors and achieve project expansion.
Product parameters
- Frequency range: 2405-2480MHz
- Working voltage: 24 V DC
- Transmitted power: +20dBm
- Receiving sensitivity: -103dBm Transmission rate: 250kbps
- Type of serial interface: RS4851、RS2321
- Number of network interface: RJ45*1
- Antenna gain: 4.12dBi
The connection mode is shown in the figure below:
The installation mode is as shown in the figure below:
During installation, first attach the gateway to the backplane of the cabinet, and then fix it with screws. The control cabinet with good tightness and convenient subsequent wiring arrangements should be used. The control cabinet should be placed in an open, dry and non-corrosive liquid place to avoid damaging the equipment.
FCC
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
To maintain compliance with FCC’s RF Exposure guidelines, This equipment should be installed and operated with minimum 20cm distance between the radiator and your body: Use only the supplied antenna.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>