Einhell TC-VC 1930 SA Wet and Dry Vacuum Cleaner User Manual
- June 13, 2024
- Einhell
Table of Contents
- TC-VC 1930 SA Wet and Dry Vacuum Cleaner
- Safety regulations
- Layout and items supplied
- Proper use
- Technical data
- Before starting the equipment
- Operation
- Replacing the power cable
- Cleaning, maintenance and ordering of spare parts
- Disposal and recycling
- Storage
- Service information
- Warranty certificate
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
TC-VC 1930 SA
Original operating instructions
Wet and dry vacuum cleaner
TC-VC 1930 SA Wet and Dry Vacuum Cleaner
|
---|---
Danger! – Read the operating instructions to reduce the risk of injury
Danger!
When using the equipment, a few safety precautions must be observed to
avoid injuries and damage. Please read the complete operating instructions and
safety regulations with due care. Keep this manual in a safe place, so that
the information is available at all times. If you give the equipment to any
other person, hand over these operating instructions and safety regulations as
well. We cannot accept any liability for damage or accidents which arise due
to a failure to follow these instructions and the safety instructions.
Safety regulations
Danger!
Read all safety regulations and instructions.
Any errors made in following the safety regulations and instructions may
result in an electric shock, fire and/or serious injury. Keep all safety
regulations and instructions in a safe place for future use.
- Important: read the operating instructions before assembling and using the appliance for the first time.
- Check that the mains voltage is the same as the mains voltage specified on the rating plate.
- Pull out the power plug in the following circumstances: whenever the appliance is not in use, before opening the appliance and before all cleaning and maintenance work.
- Never clean the appliance with solvents.
- Never pull the plug out of the socket by pulling the cable.
- Never leave the appliance unattended when operational.
- Keep away from children.
- Take care to ensure that the power cable does not get damaged by being run over, crushed, pulled or suchlike.
- Do not use the machine if the power cable is in a less than perfect condition.
- If the power cable has to be replaced, the replacement must comply with the design specifications of the manufacturer.
- Power cable: H 05 VV – F 3 x 1.5 mm 2
- Never vacuum the following: burning matches, smoldering ash and cigarette butts, combustible, caustic, inflammable or explosive substances, vapor or liquids.
- This appliance is not suitable for vacuuming dust which can be harmful to health.
- Store the appliance in a dry indoor location.
- Never use the appliance if it is damaged.
- Only allow the appliance to be serviced by an authorized after sales service outlet.
- Only use the appliance to carry out work for which has been designed.
- Take extra care when cleaning steps.
- Use only genuine accessories and spare parts.
This equipment is not designed to be used by people (including children) with limited physical, sensory or mental capacities or those with no experience and/or knowledge unless they are supervised by a person who is responsible for their safety or they have received instructions from such a person in to how to use the equipment safely. Children must always be supervised in order to ensure that they do not play with the equipment.
Layout and items supplied
2.1 Layout (Fig. 1-3)
1. Handle | 13. Dual purpose nozzle |
---|---|
2. ON/OFF/Automatic switch | 14. Castors |
3. Head | 15. Pleated fi lter |
4. Filter cage | 16. Foamed plastic fi lter |
5. Safety fl oat valve | 17. Hook for cable store |
6. Automatic socket-outlet for electric tools | 18. Wheels |
7. Locking hook | 19. Water drain screw |
8. Tank | 20. Adapter |
9. Suction hose connection | 21. Fastening screws on the handle |
10. Blow connector | 22. Accessory holder |
11. Flexible suction hose | 23. Crevice nozzle |
12. 2-piece suction tube |
2.2 Items supplied
Please check that the article is complete as specified in the scope of
delivery. If parts are missing, please contact our service center or the sales
outlet where you made your purchase at the latest within 5 working days after
purchasing the product and upon presentation of a valid bill of purchase.
Also, refer to the warranty table in the service information at the end of the
operating instructions.
- Open the packaging and take out the equipment with care.
- Remove the packaging material and any packaging and/or transportation braces (if available).
- Check to see if all items are supplied.
- Inspect the equipment and accessories for transport damage.
- If possible, please keep the packaging until the end of the guarantee period.
Danger!
The equipment and packaging material are not toys. Do not let children play
with plastic bags, foils or small parts. There is a danger of swallowing or
suffocating!
- Handle
- Suction hose
- 2-piece suction tube
- Dual purpose nozzle
- Castor (2x)
- Pleated filter with cover
- Foamed plastic filter
- Wheel (2x)
- Adapter
- Fastening screw for handle (2x)
- Crevice nozzle
- Original operating instructions
The equipment comes with a chain ( z) on the tank bottom. The chain helps to prevent static charging during use.
Proper use
The wet and dry vacuum cleaner is designed for wet and dry vacuuming using the
appropriate fi lter. The equipment is not suitable for the vacuuming of
combustible, explosive or harmful substances.
The equipment is to be used only for its prescribed purpose. Any other use is
deemed to be a case of misuse. The user / operator and not the manufacturer
will be liable for any damage or injuries of any kind caused as a result of
this.
Please note that our equipment has not been designed for use in commercial,
trade or industrial applications. Our warranty will be voided if the machine
is used in commercial, trade or industrial businesses or for equivalent
purposes.
Technical data
Mains voltage………………….220-240V ~ 50/60 Hz
Power consumption: ………………………….. 1500 W
Max. power consumption
Automatic socket-outlet: …………………….. 1490 W
Max. total power consumption: …………… 2990 W
Tank volume: …………………………………………..30 l
Weight: ……………………………………………….5.9 kg
Before starting the equipment
Warning!
Before you connect the equipment to the mains supply make sure that the data
on the rating plate are identical to the mains data.
The equipment may be connected only to a shock-proof socket-outlet.
5.1 Assembling the equipment
Fitting the equipment head (Fig. 6)
The equipment head (3) is fastened to the tank (8) by the locking hooks (7).
To remove the equipment head (3), open both of the locking hooks (7) and take
off the equipment head (3). When fitting the equipment head (3), make sure that
both of the locking hooks (7) lock into place correctly.
Fitting the wheels (Fig. 5)
Fit the wheels in accordance with Fig. 5.
Fitting the handle (Fig. 4)
Use a screwdriver to fi t the handle (1) using both screws (21).
5.2 Fitting the filters
Notice!
Never use the wet and dry vacuum cleaner without a filter. Always ensure that
the filters are securely seated.
Fitting the foam fi lter (Fig. 7)
For wet vacuuming, slip the supplied foam fi lter (16) over the filter basket
(Fig. 2/4). The pleated fi lter (15) already fitted upon delivery is not
suitable for wet vacuuming.
Fitting the pleated fi lter (Fig. 8)
For dry-vacuuming, slip the pleated fi lter (Fig. 15) over the fi lter basket
(Fig. 2/4). The pleated fi lter (15) is suitable for dry-vacuuming only.
Fitting the dirt bag (not supplied)
For vacuuming fi ne, dry dirt it is recommended that you also fi t the dirt bag.
This will ensure that the pleated fi lter (15) does not clog up so quickly and
help maintain the vacuuming power. It also makes it easier to dispose of the
dust. Slip the dirt bag over the vacuuming hole. The dirt bag is suitable for
dry-vacuuming only.
5.3 Fitting the suction hose (Fig. 9-12)
Connect the suction hose (11) to the corresponding connector on the wet and
dry vacuum cleaner, depending on the application required.
Vacuuming
Connect the suction hose (11) to the suction hose connector (9).
Blowing
Connect the suction hose (11) to the blow connector (10).
To extend the suction hose (11) you can attach one or more of the elements
which make up the 2-part suction tube (12) to the suction hose (11).
5.4 Suction nozzles Combination nozzle (13)
The dual-purpose nozzle (13) is for vacuuming solids and liquids over medium
to large areas.
Operation
6.1 ON/OFF switch (Fig. 2/2)
Switch position 0: Off
Switch position I: Normal mode
Switch position AUTO: Automatic mode
6.2 Dry vacuuming
For dry-vacuuming, use the pleated fi lter (15). In addition, you can also fi t
the dirt bag. (See point 5.2)
Always ensure that the filters are securely seated.
6.3 Wet vacuuming
For wet-vacuuming, use the foam fi lter (16) (see point 5.2).
Check that the fi lter is securely seated at all times.
Water drain screw (Fig. 1)
To make the tank (8) easier to empty after wet vacuuming, it is fitted with a
water drain screw (19). Open the water drain screw (19) by turning it
anticlockwise and drain the liquid.
When wet vacuuming, the floating safety switch (5) closes when the maximum tank
level is reached. At the same time, the suction noise of the equipment will
change and become louder. You must then switch off the equipment and empty the
tank.
Danger!
The wet and dry vacuum cleaner is not suitable for the vacuuming of
combustible liquids. For wet vacuuming, use only the supplied foam fi lter.
6.4 Automatic mode
Connect the power cable of your electric tool to the automatic socket-outlet
(6) and connect the suction hose (11) to the vacuuming connector of your
electric tool. Check that the connections are secure and air-tight.
Set the switch (2) on the wet and dry vacuum cleaner to position „AUTO“
(automatic mode).
The moment you switch on the electric tool, the wet and dry vacuum cleaner
switches on as well.
When you switch off the electric tool, the wet and dry vacuum cleaner switches
off as well after a pre-set delay.
6.5 Blowing
Connect the suction hose (11) to the blow connector (10) on the wet and dry
vacuum cleaner.
Replacing the power cable
Danger!
If the power cable for this equipment is damaged, it must be replaced by the
manufacturer or its after-sales service or similarly trained personnel to
avoid danger.
Cleaning, maintenance and ordering of spare parts
Danger!
Always pull out the mains power plug before starting any cleaning work.
8.1 Cleaning
- Keep all safety devices, air vents and the motor housing free of dirt and dust as far as possible.
- We recommend that you clean the equipment immediately after you use it.
8.2 Cleaning the equipment head (3)
Clean the equipment regularly with a damp cloth and some soft soap. Do not use
cleaning agents or solvents; these may be aggressive to the plastic parts in
the equipment.
8.3 Cleaning the tank (8)
The tank can be cleaned with a damp cloth and some soft soap or under running
water, depending on the amount of dirt.
8.4 Cleaning the filters
Cleaning the pleated fi lter (15)
Clean the pleated fi lter (15) regularly by carefully patting it and cleaning
it with a fi ne brush or hand brush.
Cleaning the foam fi lter (16)
Clean the foam fi lter (16) with a little soft soap under running water and
allow it to air-dry.
8.5 Maintenance
At regular intervals and before each use, check that the filters in the wet and
dry vacuum cleaner are securely fitted.
8.6 Ordering replacement parts:
Please quote the following data when ordering replacement parts:
- Type of machine
- Article number of the machine
- Identification number of the machine
- Replacement part number of the part required
For our latest prices and information please go to www.Einhell- Service.com
Disposal and recycling
The equipment is supplied in packaging to prevent it from being damaged in transit. The raw materials in this packaging can be reused or recycled. The equipment and its accessories are made of various types of material, such as metal and plastic. Never place defective equipment in your household refuse. The equipment should be taken to a suitable collection center for proper disposal. If you do not know the whereabouts of such a collection point, you should ask in your local council offices.
Storage
Store the equipment and accessories out of children’s reach in a dark and dry
place at above freezing temperature. The ideal storage temperature is between
5 and 30 °C. Store the electric tool in its original packaging.
**For EU countries only
Never place any electric power tools in your household refuse.
To comply with European Directive 2012/19/EC concerning old electric and
electronic equipment and its implementation in national laws, old electric
power tools have to be separated from other waste and disposed of in an
environment-friendly fashion, e.g. by taking to a recycling depot.
Recycling alternative to the return request:**
As an alternative to returning the equipment to the manufacturer, the owner of
the electrical equipment must make sure that the equipment is properly
disposed of if he no longer wants to keep the equipment.
The old equipment can be returned to a suitable collection point that will
dispose of the equipment in accordance with the national recycling and waste
disposal regulations. This does not apply to any accessories or aids without
electrical components supplied with the old equipment.
The reprinting or reproduction by any other means, in whole or in part, of
documentation and papers accompanying products is permitted only with the
express consent of the Einhell Germany AG.
Subject to technical changes
Service information
We have competent service partners in all countries named on the guarantee
certificate whose contact details can also be found on the guarantee
certificate. These partners will help you with all service requests such as
repairs, spare and wearing part orders or the purchase of consumables.
Please note that the following parts of this product are subject to normal or
natural wear and that the following parts are therefore also required for use
as consumables.
Category | Example |
---|---|
Wear parts* | Combination nozzle, crevice nozzle, upholstery nozzle, electric |
tool adapter, etc.
Consumables*| Pleated fi lter, foam fi lter, dirt bag, additional fi lter, etc.
Missing parts|
-
Not necessarily included in the scope of delivery!
In the eff ect of defects or faults, please register the problem on the internet at www.Einhell-Service.com.
Please ensure that you provide a precise description of the problem and answer the following questions in all cases:- Did the equipment work at all or was it defective from the beginning?
- Did you notice anything (symptom or defect) prior to the failure?
- What malfunction does the equipment have in your opinion (main symptom)?
Describe this malfunction.
Warranty certificate
Dear Customer,
All of our products undergo strict quality checks to ensure that they reach
you in perfect condition. In the unlikely event that your device develops a
fault, please contact our service department at the address shown on this
guarantee card. You can also contact us by telephone using the service number
shown.
Please note the following terms under which guarantee claims can be made:
- These guarantee terms apply to consumers only, i.e. natural persons intending to use this product neither for their commercial activities nor for any other self-employed activities. These warranty terms regulate additional warranty services, which the manufacturer mentioned below promises to buyers of its new products in addition to their statutory rights of guarantee. Your statutory guarantee claims are not affected by this guarantee. Our guarantee is free of charge to you.
- The warranty services cover only defects due to material or manufacturing faults on a product which you have bought from the manufacturer mentioned below and are limited to either the rectification of said defects on the product or the replacement of the product, whichever we prefer. Please note that our devices are not designed for use in commercial, trade or professional applications. A guarantee contract will not be created if the device has been used by commercial, trade or industrial business or has been exposed to similar stresses during the guarantee period.
- The following are not covered by our guarantee: – Damage to the device caused by a failure to follow the assembly instructions or due to incorrect installation, a failure to follow the operating instructions (for example connecting it to an incorrect mains voltage or current type) or a failure to follow the maintenance and safety instructions or by exposing the device to abnormal environmental conditions or by lack of care and maintenance. – Damage to the device caused by abuse or incorrect use (for example overloading the device or the use or unapproved tools or accessories), ingress of foreign bodies into the device (such as sand, stones or dust, transport damage), the use of force or damage caused by external forces (for example by dropping it). – Damage to the device or parts of the device caused by normal or natural wear or tear or by normal use of the device.
- The guarantee is valid for a period of 24 months starting from the purchase date of the device. Guarantee claims should be submitted before the end of the guarantee period within two weeks of the defect being noticed. No guarantee claims will be accepted after the end of the guarantee period. The original guarantee period remains applicable to the device even if repairs are carried out or parts are replaced. In such cases, the work performed or parts fitted will not result in an extension of the guarantee period, and no new guarantee will become active for the work performed or parts fitted. This also applies if an on-site service is used.
- To make a claim under the guarantee, please register the defective device at: www.Einhell-Service.com. Please keep your bill of purchase or other proof of purchase for the new device. Devices that are returned without proof of purchase or without a rating plate shall not be covered by the guarantee, because appropriate identification will not be possible. If the defect is covered by our guarantee, then the item in question will either be repaired immediately and returned to you or we will send you a new replacement.
Of course, we are also happy offer a chargeable repair service for any defects
which are not covered by the scope of this guarantee or for units which are no
longer covered. To take advantage of this service, please send the device to
our service address.
Also refer to the restrictions of this warranty concerning wear parts,
consumables and missing parts as set out in the service information in these
operating instructions.
Declaration of conformity: We declare conformity in accordance with the
EU directive and standards for article
Wet and dry vacuum cleaner TC-VC 1930 SA (Einhell)
2014/29/EU
2005/32/EC2009/125/EC
(EU)2015/1188
2014/35/EU
2006/28/EC
2014/30/EU
2014/32/EU
2014/53/EU
2014/68/EU
(EU)2016/426
Notified Body:
(EU)2016/425
2011/65/EU(EU)2015/863| 2006/42/EC
Annex IV
Notified Body:
Reg. No.:
2000/14/EC2005/88/EC
Annex V
Annex VI
Noise: measured LWA = dB (A); guaranteed LWA = dB (A)
P = kW; L/Ø = cm
Notified Body:
2012/46/EU(EU)2016/1628
Emission No.:
---|---
Standard references: EN 60335-1; EN 60335-2-2; EN 62233; EN 55014-1; EN
55014-2; EN 61000-3-2; EN 61000-3-3
Einhell Germany AG · Wiesenweg 22 · D-94405 Landau/ISTAR
Landau/Isar, den 20.04.2021|
---|---
First CE: 15
Art.-No.: 23.421.95
I.-No.: 21021
Subject to change without notice| Archive-File/Record: NAPR025731
Documents registrar: Sergey Hirsekorn
Wiesenweg 22, D-94405 Landau/Isar
Declaration of conformity
We, Einhell UK Ltd
Champions Business Park, First Floor Unit 10, Arrowe Brook Rd, Upton, Wirral
CH49 0AB, United Kingdom declare the conformity to UK standards and
legislation was assessed for:
Wet and dry vacuum cleaner TC-VC 1930 SA (Einhell)
UK legislation
Simple Pressure Vessels (Safety) Regulation
Electrical Equipment (Safety) Regulation
Radio Equipment Regulation
Personal Protective Equipment Regulation
Noise Emission in the Environment by Equipment for use Outdoors Regulation
The Ecodesign for Energy-Related Products and Energy Information Regulation
The Restriction of the Use of Certain Hazardous Substances in Electrical and
Electronic Equipment Regulation
Electromagnetic Compatibility Regulation
Measuring Instruments Regulation
Pressure Equipment (Safety) Regulation
Supply of Machinery (Safety) Regulation
Standards: BS 60335-1; BS 60335-2-2; BS 62233;
BS 55014-1; BS 55014-2; BS 61000-3-2; BS 61000-3-3
Wirral, 2021.04.06|
---|---
Article Number: 23.421.95 I.-No.: 21021
Subject to change without notice| Archive-File/Record: NAPR025731
Documents registrar: Sergey Hirsekorn
Wiesenweg 22, 94405 Landau/Isar, Germany
EH 05/2021 (01)
Anl_TC_VC_1930_SA_SPK7_UKCA.indb 18
11.05.2021 10:24:10
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>