HAMPTON B0040 Connected Smart Door Lock Instruction Manual

June 6, 2024
HAMPTON

HAMPTON logo

HAMPTON B0040 Connected Smart Door Lock

Need help? Download the Array By Hampton™ app or visit www.Array.care for installation videos or call 1-800-850-LOCK (5625).

Box Contents

Box Contents 1

Box Contents 2

tools

IMPORTANT INSTALLATION

  • Remove the battery from the battery compartment and charge it in the Charging Cradle until the LED turns green.
  • The Array By Hampton™’s connected door lock has a built-in solar panel that will charge the battery if positioned in direct sunlight. If unable to position the connected door lock in direct sunlight, you may need to charge the battery more frequently. You will see the battery status on theapp.
  • Do not attempt to disassemble any internal components of the connected door lock. You may void the warranty. Please see warranty details printed on the last page of the installation instructions.
  • Do not install the battery until you’ve installed the connected door lock and downloaded the app. Follow the instructions in order.
  • Do NOT use a power drill to install the connected door lock. A power drill should only be used for door preparation.
  • Make sure your door is properly aligned and can be closed without pushing, pulling or lifting the door.

Compatible Devices:

Note: New devices will continue to be added to enhance your experience with the Array By Hampton™ connected door lock. Please visit our website www.arraylock.com for a complete list of compatible devices.

Installation Overview

Installation Overview 1

Part Description
A Key
B Exterior Assembly
C Cylinder
D Tailpiece
E Power Cable
F Gasket
G Latch
H Interior Mounting Plate
I Interior Assembly
J Rechargeable Battery
K Antenna Cover
L Battery Cover
M Tailpiece Receiver
N Strike Plate
O Reinforcement Plate
P Dust Box
Q Screw Cover

Pre-Installation Instructions

Charge Battery

a. Remove the Battery Cover (L), Rechargeable Battery (J), Battery Charging Cradle, USB Cable and Wall Adapter. Remove the plastic tab on the Battery (J). Slide the Battery (J) into the Charging Cradle from the side. Charge the Battery (J) until the LED Light turns from red to green.

Pre-Installation Instructions 1

b. Carefully remove the Antenna Cover (K) by gently pulling the edges outward slightly and lifting.

Pre-Installation Instructions 2

Watch the Installation Video
The Array By Hampton™ connected door lock is compatible with either iOS® or Android™ devices. Search for “Array By Hampton™ Connected Door Lock” at the App Store or Play Store to download the free app. Once the app is downloaded, register your connected door lock and watch the installation video. Install your Array By Hampton™ connected door lock (Steps 3 – 5) and then follow the instructions to add a lock or visit www.Array.care for additional support.

Prep the Door • FITS DOORS 1-3/8″ (35 mm) TO 1-3/4″ (45 mm) THICK •

a. If replacing an existing deadbolt. Remove the old hardware and begin at STEP 4.
b. If installing the Array By Hampton™ connected door lock on a new door, follow the door preparation instructions on PAGE 9 and use the template provided on PAGE 10.

Install Latch and Strike Plate

Install Strike Plate (N) in the Door Frame

Install Latch and Strike Plate

Determine the Proper Faceplate

Install Latch and Strike Plate 1

Set the Latch Backset
The distance from the center of the bore hole to the edge of the door is called the backset. If the backset of your door is 2-3/8″, you don’t need to adjust the latch. The backset is preset for 2-3/8″.
If the backset of your door is 2-3/4″, you’ll need to adjust the latch as shown.

Install Latch and Strike Plate 2

Install the Latch
CAUTION: Be sure the latch is in the upright position.

Deadbolt Installation Instructions

Install Lock Assemblies

Deadbolt Installation Instructions 1

Deadbolt Installation Instructions 2

Deadbolt Installation Instructions 3

Deadbolt Installation Instructions 4

Deadbolt Installation Instructions 5

Deadbolt Installation Instructions 6

Deadbolt Installation Instructions 7

Deadbolt Installation Instructions 8 Deadbolt
Installation Instructions 9

Return to the app and follow the instructions to Add a Lock

Door Preparation Instructions for New Doors

If installing the Array By Hampton™ connected door lock on a new door, follow the door preparation instructions and use the template on Page 10.

Mark Door with Template

a. Mark the centerline for the deadbolt about 44″ (1120 mm) from the floor, or about 5-1/2″ (140 mm) abovethe center ofan existing knob orlever.
b. Apply the template to the door with the dotted fold line on the door edge.
c. Select the 2-3/8″ (60 mm) or 2-3/4″ (70 mm) backset and mark the center for the hole for the deadbolt on the door face. (Most residential doors have a 2-3/8″ backset.)
d. Mark the center for the latch hole on the door edge according to the thickness of your door.

Door Preparation Instructions for New Doors 1

Drill Holes

a. Drill a 2-1/8″ (54 mm) hole on the door face from both sides to avoid splitting wood.
b. Drill a 1″ (25.4 mm) hole in the door edge for the latch.
c. Insert latch into hole, mark outline of faceplate, and chisel 1/8″ (3 mm) deep or until the faceplate is flush with the dooredge.
d. Mark latch screw holes and drill two 1/8″ (3 mm) pilot holes for the Latch Screws.

Door Preparation Instructions for New Doors 2

Prepare Door Jamb for Strike Plate
a. Mark centerline on the door jamb exactly opposite the latch hole in the door edge. Make sure that the mark is correct so that the latch bolt will enter the strike plate without interference when the deadbolt is locked.
b. Usingthestrikeplateasapattern,drill the latch and screw holes, and chisel out amortise until the strike plate fits flush.

Door Preparation Instructions for New Doors 3

Door Preparation Instructions for New Doors 4

ARRAY BY HAMPTON™ BATTERY MANUFACTURER’S INSTRUCTIONS

WARNING:

  • Misusing the battery may cause it to get hot, explode, or ignite and cause injury. Follow the safety rules listed below:

    • Do not place battery in fire or heat the battery.
    • Do not penetrate the battery with nails, strike the battery with a hammer, step on the battery, or otherwise subject it to strong impacts or shocks.
    • Do Not Open, Crush, Heat Above 55°C (131°F), or Incinerate.
    • Do not solder directly onto the battery.
  • Do not disassemble or modify the battery. The battery contains safety and protection devices which, if damaged, may cause the battery to generate heat, explode, or ignite.

  • Do not place the battery on or near fires, stoves, or other high-temperature locations.

    • Do not place the battery in direct sun or use or store the battery inside hot conditions.
      Doing so may cause the battery to generate heat, explode, or ignite.
  • Immediately discontinue use of the battery if, while using, charging, or storing the battery, it emits an unusual smell, feels hot, or appears abnormal in any other way.

  • In the event that the battery leaks and the fluid gets into one’s eye, do not rub the eye. Rinse well with water and immediately seek medical care. If left untreated, the battery fluid could cause damage to the eye.

  • The temperature range for using the battery is -10°C to 55°C (14°F to 131°F). Use of the battery outside of this temperature
    range may damage the performance of the battery or may reduce its life expectancy.

  • Do not use the battery in any device except the Array By Hampton™ Connected Door Lock.

FCC GENERAL STATEMENT

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o” and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna, or increase the separation between the equipment and receiver.
  • Connect the receiver to a di”erent outlet.
  • Consult Hampton Products International Corporation or an experienced radio/TV technician for help.
  • Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment (i.e. any changes or modification that may influence the specification of radiofrequency relating to the Wi-Fi® is prohibited). FCC ID Number: 2ANTYB0040

Wi-Fi® is a registered trademark of Wi-Fi Alliance®.

WARRANTY

Full Lifetime mechanical & finish warranty and limited one-year electronics warranty.

Subject to the terms and conditions of this warranty, Hampton Products Int’l Corp. (“Hampton”) extends a full lifetime mechanical and finish warranty and a limited one-year electronics warranty to the original residential user (“Original User”) of this product (“Product”) against defects in material and workmanship as long as the Original User occupies the residential premises upon which the Product was originally installed. This warranty only applies to the Original User of Product. This Warranty is not transferable. Upon pre- authorized return of defective Product to Hampton, Hampton may repair or replace the Product with a new or refurbished product at Hampton’s sole discretion.

What is NOT covered:
The following costs, expenses and damages are not covered by the provisions of this limited warranty: (1) labor costs including, but not limited to, such costs for the removal and reinstallation of Product; (2) shipping and freight expenses required to return Product to Hampton; (3) failures, defects, or damage (including, but not limited to, any security failure or loss of data), caused by any third party product, service, or system connected or used in conjunction with the Product, and; (4) any other incidental, consequential, indirect, special and/or punitive damages, whether based on contract, warranty, tort (including, but not limited to, strict liability or negligence), patent infringement, or otherwise, even if advised of the possibility of such damages. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above exclusion or limitation may not apply to you. This warranty give you specific legal rights and you may also have other rights that vary from state to state.

The provisions of this Warranty do not apply to Products: (i) used in commercial applications; (ii) used in common area applications; (iii) used for purposes for which they are not designed or intended; (iv) which have been subjected to alteration, abuse, misuse negligence or accident; (v) which have been improperly stored, installed, maintained or operated; (vi) which have been used in violation of written instructions provided by Hampton; (vii) which have been subjected to improper temperature, humidity or other environmental conditions; (viii) which, based on Hampton’s examination, do not disclose to Hampton’s satisfaction non-conformance to the warranty. Additionally, the limited lifetime warranty

DOES NOT COVER scratches, abrasions, or deterioration due to the use of paints, solvents or other chemicals, abuse, misuse, or Product used in commercial applications.
Additional terms: Hampton does not authorize any person to create for it any obligation or liability in connection with the Product. Hampton’s maximum liability is limited to the original purchase price of the Product. No action arising out of any claimed breach of this warranty by Hampton may be brought by the Original User more than one (1) year after the cause of action has arisen.

Exclusions:
Tuscan Bronze® finish is designed to improve over time and change in appearance, creating a living finish through daily use and, thus, finish discoloration is not applicable to the above warranty.

For assistance or specific warranty details and limitations information, please call 1-800-850-5625 in the U.S and Canada, or visit www.arraylock.com

50 Icon, Foothill Ranch, CA 92610-3000 USA www.arraylock.com | 1-800-850-5625 Deadbolt assembly made in Taiwan.
Solar panel & batteries made in China. Programmed & packaged in the USA.

For Support:www.Array.Care
email: info@hamptonproducts.com

Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance 20 cm between the radiator your body.

Product specification


Product name| Smart Lock Array By Hampton|
Product model| 2354X
Operating temperature| -10℃ – 55℃
Operating humidity| 40℃≤93%RH
Wifi RF| Frequency range: 2.412 GHz – 2.484 GHz mode: IEEE802.11 b/g/n

Maximum output power:16.08dBm

BLE RF| BLE 4.2& BLE 5.0

Maximum output power: 8.1dBm (Bluetooth function is only used to search for device SSID)

Power| 3.7 V⎓ 1A (⎓ Direct current)
Battery Charger(US type)| MODEL:WKC0020

I/P: 4.9V-5.5V O/P:4.2V⎓ 2A

Switching adapter (US type)| MODEL:DSA-10PFL-05 FUS 05020

I/P: 100-240V~, 50/60Hz, 0.3A Max O/P:5V⎓ 2A

Rechargeable Li-Polymer Battery (US type)| Part#:98-10001

Voltage:3.7V Capacity:52000mAh Watt Hours:19.24

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

HAMPTON User Manuals

Related Manuals