Yinchuandao XD01 Wi-Fi Camera User Manual
- June 1, 2024
- Yinchuandao
Table of Contents
Yinchuandao XD01 Wi-Fi Camera
Product Information
Specifications:
- Power Supply: 3.7V-5V/1A-2A
- Network: 2.4G WiFi
- Storage: TF card (supports FAT format)
- Compatibility: Android and iOS devices
Product Usage Instructions
Introduction to Appearance:
Our mini WiFi camcorder requires a power supply (3.7V-5V/1A-2A) to operate as
it does not have a built-in battery. The camera will turn on automatically
once the power is connected.
APP Download Method:
For Android devices, scan the QR code or search for [ULooka] in the app store
to download the app. For iOS devices, scan the QR code or search for the app
in the App Store. Once downloaded, open the app, read the Privacy Policy, and
click Agree.
Network Configuration:
- Connect the device to the power supply and reset it by pressing and holding the reset button until the indicator light flashes slowly for about 3 seconds.
- Open the app, click Add Device, and select Surveillance Camera with Hotspot.
- Select the device hotspot connection starting with ALxxx on the WLAN interface.
- After a successful connection, configure WiFi according to the prompts.
- Once network configuration is successful, the device will display online, allowing remote control via the app.
Notes:
- Avoid using the product in excessively humid environments to prevent water ingress.
- Avoid positioning the camera lens near glass or reflective surfaces to ensure optimal image quality.
- Install the product within Wi-Fi signal coverage and away from signal interference sources like microwave ovens.
- The device supports TF card video recording storage and only works with 2.4G WiFi networks.
FAQ:
-
Q: Can I use a 5G WiFi network with this camera?
A: No, the device only supports 2.4G WiFi networks and does not support 5G at this time. -
Q: What format does the TF card need to be for video recording?
A: The TF card should be formatted to FAT for video recording storage.
Introduction to appearance
Our mini WiFi camcorder does not have a built-in battery, you need to connect the power supply (3.7V-5V/1A-2A charging bank, charger, etc.). There is no switch button set on the camera. The camera will turn on automatically after the power is turned on.
APP Download Method
- Android mobile phones can open the browser to scan the QR code below or search for [ULooka] to download; IOS phones come with cameras, etc., scan the QR code below or search for downloads in the APP Store.
- Open the app, read the “Privacy Policy”, and click “Agree”. APP pop-up prompt: Message push notification permission, APP positioning permission, please go to Settings and Confirm.
ULooka
Network configuration
-
Connect the device to the power supply, press and hold the reset button to reset, and the indicator light “flashes slowly” for about 3 seconds.
-
Open the APP, click Add Device, and select “Surveillance Camera with Hotspot ” (as shown in the figure).
-
Click “I want to connect my phone to the AP now”, when jumping to the WLAN interface, select the device hotspot connection starting with “ALxxx”; For IOS phones, you need to manually open the WLAN interface and select the device hotspot connection.
Note: When prompted with something like “The current network cannot access the Internet, please switch to another network”, please keep the device hotspot connected (as shown below).
-
After the connection is successful, the Android phone will automatically jump to the APP home page, please configure WIFI according to the prompts (as shown below).
-
After the network configuration is successful, the device displays “online”, that is, the network configuration is successful, and the APP can be used to remotely control and access.
Important Notes
- The applicable working temperature of this product is -10 °C ~ 50 °C, do not use this product in an environment where the temperature is too high or too low.
- This product is a precision electronic product, do not use this product in an environment that has excessive humidity or may cause water ingress of this product, so as not to affect normal use.
- To better use this product, avoid the front and side of the lens close to glass, white walls and other reflective objects, so as not to cause the picture near bright, far dark or white phenomenon.
- Please ensure that this product is installed within the range of Wi-Fi signal coverage and placed in a better location with a Wi-Fi signal as much as possible; Try to install it away from microwave ovens, etc., where it may affect the signal.
- The device only supports 2.4G WiFi and does not support 5G or WIFI with special symbols for the time being.
- The device supports TF card video recording storage, and the TF card only supports the FAT format.
FCC Warning Statement
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, under Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used by the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
RF Exposure Statement
To maintain compliance with FCC’s RF Exposure guidelines, This equipment
should be installed and operated with a minimum distance of 20cm from the
radiator of your body. This device and its antenna(s) must not be co-located
or operated in conjunction with any other antenna or transmitter.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>