OVE BREEZE PRO 38 Satin Nickel Finish Instruction Manual

May 15, 2024
OVE

BREEZE PRO 38
INSTALLATION MANUAL
SHOWER ENCLOSURE

OVE BREEZE PRO 38 Satin Nickel Finish

BREEZE PRO 38 Satin Nickel Finish

An installation video guide can be found on our Youtube channel: youtu.be/LuvFg8VUM8U

OVE BREEZE PRO 38 Satin Nickel Finish - Symbol 1
Questions, problems, need help?
Call our customer service department at
1-866-839-2888, 9 a.m. – 5 p.m., EST, Monday – Friday

customerservice@ovedecors.com
www.ovedecors.com

DO NOT START WITH THIS INSTALLATION MANUAL

  1. FIRST, INSTALL YOUR SHOWER BASE (AN INSTALLATION MANUAL CAN BE FOUND IN THE SHOWER BASE PACKAGE).
  2. SECOND, INSTALL YOUR SHOWER WALL PANELS, IF APPLICABLE (AN INSTALLATION MANUAL CAN BE FOUND IN THE WALL PANELS PACKAGE).
  3. THIRD, INSTALL YOUR SHOWER ENCLOSURE (USING THIS MANUAL).

An installation video guide can be found on our Youtube channel: youtu.be/LuvFg8VUM8U

SAFETY INFORMATION

CAUTION
Please carefully read the following important safety information before handling or installing this shower. There is a risk of serious injury while handling this product. To minimize these risks, please note:

  • Always wear safety glasses and gloves while handling.
  • Always read and follow all the steps in the installation instructions.
  • Inspect all contents and glass for damage before installation.
  • Extreme caution should be taken while handling the glass during installation as the tempered glass may shatter if in contact with a hard surface.
  • Handle the tempered glass with caution! Improperly handling the glass can cause it to break suddenly in small pieces (never in pointed fragments).
  • Always take all precautions not to touch the tempered glass with any tools during the installation, or after installed.
  • Do not cut or modify the tempered glass as it will shatter if cut.
  • Carefully remove product from packaging and keep packaging until installation is complete.
  • Inspect all parts for damage; if there is damage to the unit prior to installation, please contact customer service at the number provided in this guide.
  • Install the shower on a floor that is level and able to accommodate the weight of the unit and an occupant.
  • Consult local building codes and compliance standards prior to installation and ensure conformity.
  • After installation, and from time to time, check the glass for fit and finish to ensure that nothing has come loose since installation.
  • Keep this installation manual for future reference.

SAFETY NOTICE

NOTICE

  • Any modification or alteration from what is specified in this instruction manual will void any and all warranty on this product.
  • The distributor is not responsible for any damage to the unit or personal property caused by improper installation. If you disregard instructional warnings, you will void your warranty and possibly deal with water damage.
  • Consult the distributor’s website for any additional information or question on this product’s installation.

PREPARATION

OVE BREEZE PRO 38 Satin Nickel Finish - Symbol 2

You will need at least two people to install this unit properly.
Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list and hardware contents list.
If any part is missing or damaged, do not attempt to assemble the product.
Estimated Assembly Time: Shower (0.5 h)

PACKAGE CONTENT

OVE BREEZE PRO 38 Satin Nickel Finish - PACKAGE
CONTENTOVE BREEZE PRO 38 Satin Nickel
Finish - PACKAGE CONTENT 2

PART LIST

PART # DESCRIPTION QUANTITY CODE
A Wall track (fixed panel) 1 Chrome: 99STR3715-WM

Satin Nickel: 99STR3717-WM
Matt Black: 99STR3719-WM
B| Fixed panel| 1| 99SG3704-WM
C| Door panel| 1| 99SG3706-WM
D| Wall track (door panel)| 1| Chrome: 99STR3721-WM
Satin Nickel: 99STR3723-WM
Matt Black: 99STR3725-WM
E1| Fixed panel gasket (long)| 1| 99SRU3655-WM
E2| Fixed panel gasket (short)| 1| 99SRU3671-WM
F1| Top support bar
(For reverse installation, this becomes the bottom bar)| 1| Chrome: 99SGS3665-WM
Satin Nickel: 99SGS3667-WM
Matt Black: 99SGS3669-WM
F2| Bottom support bar
(For reverse installation, this becomes the top bar)| 1| Chrome: 99SGS3671-WM
Satin Nickel: 99SGS3673-WM
Matt Black: 99SGS3675-WM
G| Glass panel vertical seal strip| 2| 99SRU3657-WM
H| Door roller (top) (PRE-INSTALLED)| 2| Chrome: 99SWE3622-WM
Satin Nickel: 99SWE3631-WM
Matt Black: 99SWE3632-WM
I| Door roller (bottom) (PRE-INSTALLED)| 2| Chrome: 99SWE3623-WM
Satin Nickel: 99SWE3633-WM
Matt Black: 99SWE3634-WM
J| Door handle| 1| Chrome: 99SHA3620-WM
Satin Nickel: 99SHA3628-WM
Matt Black: 99SHA3629-WM
K| Assembly securement tool (for installation only)| 1| 99SHW0360-WM
* | Complete hardware kit| 1| Chrome: 99SHW0361-WM
Satin Nickel: 99SHW0374-WM
Matt Black: 99SHW0375-WM

SUPPLIED HARDWARE LIST

| Wall Anchor
ø6x30mm
8+2
---|---
| Screw
ST4x30mm
8+2
| Fitting 8+2
| Cap 8+2
| Gasket push tool 1x
| Cap 4x
| Allen key
2mm & 2.5mm & 3mm & 4mm

TOOLS REQUIRED (not supplied)

|
---|---
Pencil| Screwdriver
|
Drill and drill bits| Cutter
|
Measuring Tape| Level
|
Silicone| Rubber mallet
|
Safety glasses| Ratchet

REVERSIBILITY

This instruction is drawn up for a door opening from right to left (see illustration A).
For an installation for a door opening from left to right (see illustration B), use the same instructions, but switch around the panels: mirror effect.

OVE BREEZE PRO 38 Satin Nickel Finish - REVERSIBILITY

FAQ

Q: If the shower head is installed on the other wall, will it leak?

A: It is possible to install your shower head on the other side, but we strongly recommend to install it as illustrated.

Install the shower head on the door’s side as shown in the illustration! This will reduce the risk of leaking.

SHOWER DIMENSIONS

OVE BREEZE PRO 38 Satin Nickel Finish - SHOWER
DIMENSIONS

| Measurements Mesures Medidas
---|---
A| Wall panel width Largeur
B| Wall panel height Hauteur
C| Shower height
D| Shower width
E| Base width
F| Fixed panel width
G| Door panel width
H| Door opening
I| Distance between handle holes

OVE BREEZE PRO 38 Satin Nickel Finish - SHOWER DIMENSIONS
2Measures: inch [millimeter]

SHOWER INSTALLATION: OVERVIEW

A. Before you start the installation of your product consult the illustration A below showing a side-view of the completed installation.
B. Illustration B shows the recommended wall structure and measurements for the product installation.
NOTE: Customer must follow and comply with the local and national building and plumbing codes. All illustrations in this manual are for reference only and do not take precedent on any code or regulation. This product should be installed by a professional.

FAQ

Q: What thickness of cement must I apply?

A: Between 1” and 1 1/2”.

Q: Is the base installed on the studs or on the drywall?

A: On the studs.

OVE BREEZE PRO 38 Satin Nickel Finish - OVERVIEW

#1 SHOWER FRAME INSTALLATION
IMPORTANT: Ensure that the securement clip inside the support bars (F1 & F2) faces in the correct direction to secure the fixed panel.
A-B. Install the 2 wall tracks (A & D) onto the bottom support bar (F2).
C-D. Position the fixed panel (B) onto the bottom support bar (F2) and insert it into the wall track (A). Ensure the fixed panel (B) is inserted into the securement clip on the bottom support bar (F2).

OVE BREEZE PRO 38 Satin Nickel Finish - SHOWER FRAME
INSTALLATION

#2 SHOWER FRAME INSTALLATION
A-C. Install the top support bar (F1) onto the wall tracks (A & D). Ensure the fixed panel (B) is inserted into the securement clip on the top support bar (F1).

OVE BREEZE PRO 38 Satin Nickel Finish - SHOWER FRAME INSTALLATION
2

#3 HOW TO DISASSEMBLE THE SUPPORT BARS
HELPFUL HINT:
The top and bottom support bars (F1 & F2) are secured to the wall tracks (A & D) with a spring-loaded pin. They can be easily disassembled following the below steps.
A-B. In the instance that the support bars would need to be removed: Insert an Allen key and pull the spring-loaded pin inside the top or bottom support bars to free up the connection between the support bars (F1 & F2) and the wall tracks (A & D). Then, while maintaining the pull on the pin, lift the support bar up and out of the wall track.

OVE BREEZE PRO 38 Satin Nickel Finish - DISASSEMBLE THE SUPPORT
BARS

#4 SHOWER FRAME INSTALLATION
A-C. Place and secure assembly securement tool (K) onto the top and bottom support bar (F1 & F2), using the blocks located on the 2 ends of the bar (K).
NOTE: The assembly securement tool (K) holds together the whole shower frame while it is moved around to be placed on the shower base.

OVE BREEZE PRO 38 Satin Nickel Finish - SHOWER FRAME INSTALLATION
3

#5 SHOWER FRAME INSTALLATION
A-C. Take the assembled shower frame and gently put it onto the installed shower base. Ensure that all is leveled. Position the frame such as the center of the wall track will be located on the center line of the shower base.
D-E. Tighten the bolts located on the inner side of the top and bottom support bars (F1 & F2), securing the wall tracks into place.
NOTE: Loosening the bolts located on the inner side of the support bars (F1 & F2) allows you to adjust the position of wall tracks (A & D) to adjust for out of plumb walls.

OVE BREEZE PRO 38 Satin Nickel Finish - SHOWER FRAME INSTALLATION
4

#6 SHOWER FRAME INSTALLATION
A-C. Mark the pre-drilled holes of the wall tracks (A & D) onto the wall, and then remove the assembled shower frame from the base.

OVE BREEZE PRO 38 Satin Nickel Finish - SHOWER FRAME INSTALLATION
5

#7 SHOWER FRAME INSTALLATION
A. Using a ø1/4” (6mm) drill bit, drill guide holes at the marked location.
B. If there are no studs located behind the wall track (A & D), then insert the wall anchors (AA) using a rubber mallet until the wall anchors are flush with the wall.

OVE BREEZE PRO 38 Satin Nickel Finish - SHOWER FRAME INSTALLATION
6

#8 SHOWER FRAME INSTALLATION
A-D. If the shower is being installed in reverse, where the door panel (C) is on the left side, uninstall the top and bottom rollers (H & I), rotate the door panel 180 degrees, and reinstall the rollers.
E-F. Put the assembled shower frame back onto the base. Secure the wall tracks (A & D) using fittings (CC), screws (BB) and caps (DD).

OVE BREEZE PRO 38 Satin Nickel Finish - SHOWER FRAME INSTALLATION
7

#9 SHOWER FRAME INSTALLATION
A. Place the gasket (E1) between the fixed panel (B) and the track (A). Use the supplied plastic pusher to push the gasket snuggly into place.
B. Place the gasket (E2) between the fixed panel (B) and the bottom support bar (F2). Use the supplied plastic pusher to push the gasket snuggly into place.
C. Uninstall the assembly securement tool (K) from the top and bottom support bars (F1 & F2).
D. If there is a small gap between the fixed panel (B) and the top support bar (F1), tighten the bolt located on top of the top support bar (F1) until the gap disappears.

OVE BREEZE PRO 38 Satin Nickel Finish - SHOWER FRAME INSTALLATION
8

#10 SHOWER DOOR INSTALLATION
A. Hang the door panel (C) by inserting the 2 top rollers (H) into the track of the top support bar (F1).
B. Gently push down on the bottom rollers (I), which will move the wheels down, allowing the wheels to lock into the track of the bottom support bar (F2).
C. After the rollers have been installed, adjust the level of the glass panel using the eccentric mechanism of the rollers. Using the same mechanism, ensure that the 2 bottom rollers (I) are well hooked into the bottom track rail.

OVE BREEZE PRO 38 Satin Nickel Finish - SHOWER DOOR
INSTALLATION

#11 SHOWER DOOR INSTALLATION
A. Install the 2 glass panels seal strips (G).
B. Install the door handle (J) using an Allen key. Install the caps (FF) onto the handle (J).

OVE BREEZE PRO 38 Satin Nickel Finish - SHOWER DOOR INSTALLATION
2

#12 SHOWER DOOR STOPPERS INSTALLATION
A-B. Adjust the door roller stoppers inside the top and bottom support bars (F1 & F2). Loosen the 2x stoppers on located on the fixed panel (B) side.
Open the door and position the door to yield a gap of 1 3/8” (35mm) between the edge of the fixed panel (B) and the door handle (J).
C-D. Tightly secure the roller stoppers using the Allen key.

OVE BREEZE PRO 38 Satin Nickel Finish - SHOWER DOOR INSTALLATION
3

#13 SHOWER DOOR STOPPERS INSTALLATION
A-B. Adjust the door roller stoppers inside the top and bottom support bars (F1 & F2). Loosen the 2x stoppers on located on the door panel (C) side.
Close the door and position the door to yield a tight seal.
C-D. Tightly secure the roller stoppers using the Allen key.

OVE BREEZE PRO 38 Satin Nickel Finish - SHOWER DOOR STOPPERS
INSTALLATION

#14 SEALING
Ensure that the door closes tightly and opens smoothly. Ensure that there is a firm connection between the fixed panel(s) and the support bar.
Apply a clear silicone water sealant around the outside perimeter of any fixed shower components. Allow 24 hours for silicone to dry. Improper application of silicone sealant may cause your shower to leak.

OVE BREEZE PRO 38 Satin Nickel Finish - SEALING

CARE AND MAINTENANCE

For the daily maintenance, use a wet cloth and a soft liquid cleaner.
Never use abrasive cleaners containing some acetone, chlorine or strong bleach, scrapers, metallic brushes, nor other objects or the products which can graze or tarnish surfaces.
Use a ratchet to strongly tighten any bolts used to support the fixed glass panels or doors panel (support bolts can withstand up to 250 lbf*in of torque).
Check these bolts every 4 months and re-tighten them if necessary.

OVE BREEZE PRO 38 Satin Nickel Finish - Symbol 1 Questions, problems, need help? OVE BREEZE PRO 38 Satin Nickel Finish -
Symbol 1
Call our customer service department at
1-866-839-2888, 9 a.m. – 5 p.m., EST, Monday – Friday

customerservice@ovedecors.com
www.ovedecors.com

LIMITED Product Warranty

The DISTRIBUTOR is a distributor of the following Products:

  • Shower Doors (warranty period 5 years).
  • Acrylic Surfaces (warranty period 5 years against blistering, cracking or chipping in the acrylic surface).
  • Acrylic Shell Structure (warranty period 5 years against loss of water through fiberglass laminate of the acrylic body).
  • Shower Hardware (handles, hinges, rubber support clips, metal support bars and wall tracks) (warranty period 1 year against defects in materials or workmanship).

Limited Warranty: The DISTRIBUTOR warrants to the original retail purchaser that within a reasonable time after notification from purchaser, The DISTRIBUTOR will repair or replace the Product, or any part or component of the covered Product, distributed by The DISTRIBUTOR which is proven to the satisfaction of The DISTRIBUTOR to be defective in workmanship or materials, and which has failed during normal use and within the warranty period. This Limited Warranty does not apply to Products that have been damaged, or which fail, as a result of causes other than manufacturing defects (such as but not limited to improper installation; lack of or improper care or maintenance; exposure to elements including corrosive products, environments or water; alteration; abuse or misuse). This warranty does not cover damage to finishes. The warranty commences on the first date a Product is purchased by the customer. This warranty applies exclusively to products purchased and used in non-commercial applications.
Warranty Claim Procedure: To make a claim please call The DISTRIBUTOR’s helpline to trouble-shoot the issue and start the claim process. Products may be inspected or evaluated by The DISTRIBUTOR and any Product or component found to meet the above warranty criteria will be repaired or replaced at The DISTRIBUTOR’s option. Replacement or repaired parts will be shipped at no cost to customer via ground freight only.
Any expedited methods of shipments are customer’s expense.
DISCLAIMER AND EXCLUSION OF WARRANTIES: This warranty is meant to be a complete and exclusive statement of the terms of all limited warranties offered by The DISTRIBUTOR.
To the fullest extent permitted by law, other than the express warranty set forth in this instrument there are NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE EXTENDED BY The DISTRIBUTOR.
This warranty gives you specific legal rights. You may also have rights, which may vary under applicable state, provinces, or national legislation, which cannot be disclaimed or modified by the above Disclaimer. Except as permitted, the Disclaimer is not intended to waive, modify, release or limit the applicability of preemptive state, province, or national legislation inconsistent with the terms of this Limited Warranty and Disclaimer. However, to the extent permitted by law, no implied warranties of merchantability or fitness are intended or extended hereunder. Notwithstanding the Disclaimer if any implied warranty is imposed by operation of law, to the extent permitted, the duration of such implied warranties is limited to the shorter of the term of the express warranty or the applicable statute of limitations.
The Products listed above are intended to be installed and used for personal, consumer residential use. Use of Products for any other purpose such as commercial purposes voids this warranty. The Limited Warranty is applicable only to the Products listed herein, and no warranty is extended to products not distributed by The DISTRIBUTOR. The warranty is applicable only to the first retail purchaser.
Transferability: This warranty is not transferrable.
LIMITATION AND EXCLUSION OF REMEDIES AND DAMAGES: The DISTRIBUTOR’s sole responsibility under this Limited Warranty shall be to repair or replace, at its option, any defective Product or component. Purchaser agrees that this is the sole and exclusive remedy under this Limited Warranty. The DISTRIBUTOR will not be responsible for any incidental, consequential, special or indirect damages, including loss of use as a result of any manufacturing defect in a Product. The DISTRIBUTOR will not be responsible for labor, or any other fees associated with removal or installation of warranted parts. Some states, provinces, or national legislation do not allow the exclusion or limitation of incidental or consequential damages, so this limitation may not apply to you.
Product modification: The DISTRIBUTOR reserves the right to change, modify or improve the Products without obligation to incorporate such changes in Products previously sold or installed.
Authority and Modification: The retail seller is not the agent of The DISTRIBUTOR and is not authorized to vary or modify the terms of the Limited Warranty. In addition, the retail seller cannot bind The DISTRIBUTOR or make any representations or promises about the Product that are binding on The DISTRIBUTOR.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals