Whirlpool WFW8540FW High Efficiency Front Load Washer User Guide
- June 13, 2024
- Whirlpool
Table of Contents
Quick Start Guide
Setting Up and Using Your High-Efficiency Front Load Washer
WFW8540FW High Efficiency Front Load Washer
WARNING
Fire Hazard
Never place items in the washer that are dampened with gasoline or other
flammable fluids.
No washer can completely remove oil.
Do not dry anything that has ever had antype of oil on it (including cooking
oils).
Doing so can result in death, explosion,or fire.
REMOVING SHIPPING BOLTS
Position the washer so that the rear is within approximately 3 ft (914 mm) of
its final location.
Keep the washer in the upright position; using a 1/2″ wrench, loosen each of
the four shipping bolts on the rear panel. Once each bolt is loose, move it to
the center of the hole and completely pull out the bolt, including the plastic
spacer and store them in a location for use if the unit needs to be moved at a
later date. IMPORTANT: If the washer is to be transported at a later date,
call your local service center for new transport bolts if the original set is
misplaced.
Machine must be transported in the upright position. To avoid structural or
suspension damage to your washer, it must be properly set up for relocation by
a certified technician.
Close the bolt holes with the four transport bolt hole plugs.
KEY AND COIN BOX*
LOCATION OF KEY Coin box key (shown) comes taped to coin box lock.
Document the key code (engraved on coin box key) in a safe place.
If key is lost, contact 1-800-221-0982
X200 or X154 for replacement (not covered by warranty). Have key code handy;
otherwise, locksmith will have to drill out coin box and replacement coin box
(part no. W11190039) will have to be installed.
*Applies only to select models.
CONNECTING WATER/SECURING DRAIN HOSE
-
CONNECT NEW INLET HOSES TO FAUCETS Insert new hose washers (in separate bag) into each end of inlet hoses. Firmly seat washers into couplings. Do not overtighten or use tape or sealants when attaching to faucets.
-
CLEAR WATER LINES
Make sure that both hot and cold water hoses are connected to the correct faucets. The washer will not operate unless both hoses are connected. Make sure that both hot and cold water hoses are connected to the correct faucets. The washer will not operate unless both hoses arconnected. -
CONNECT INLET HOSES TO WASHERAND CHECK FOR LEAKS Do not overtighten or use tape or sealants when attaching to washer Turn on faucets and check for leaks at both ends of hoses.
-
IMPORTANT:
Make sure that water faucets are turned on fully before using the washer for the first time. If there is no/low water pressure to the washer, the display will scroll “lo h2O”. To clear, open and close the washer door. -
Install and secure the drain hose in a manner that will avoid it coming out of or leaking from the plumbing/drain. Do not seal or put more than 4.5″ (114 mm) of the drain hose into drainpipe or standpipe.
SETTING UP THE WASHER
WARNING
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death, fire, or electrical
shock.
Plug in washer or connect power.
“SYNC” will be displayed for less than 1 minute. CHANGING COIN DROP PRICING
(Applies only to select models)
Refer to Installation Instructions for detailed instructions located in the
washer.
NOTE: Coin box needs to be emptied frequently to avoid jams and damage.
For coin drop use, match the wash price on the display to the number of coin
1s for Regular cycle price and the value of coin 1. See the Installation
Instructions for programming details. For a suggested setup, see the “User &
Set-Up Instructions” section of the Installation Instructions.
NOTE: To minimize the potential of oversudsing, follow this recommended
setup:
- Add a two-minute prewash length (see the “User & Set-Up Instructions” section of the Installation Instructions).
IMPORTANT WASH TIPS
- Shake out clothing prior to loading.
- Zip all zippers.
- Use the recommended amount of HE detergent.
- If a detergent pod is used, toss it into the wash drum not into the dispenser.
- Use chlorine bleach only.
- Fabric softener must be diluted.
NOTE: The washer remains locked for the entire wash cycle.
©2023 All rights reserved.
W11692818B
Todos los derechos reservados.
10/23
Documents / Resources
|
Whirlpool WFW8540FW High Efficiency Front Load
Washer
[pdf] User Guide
WFW8540FW High Efficiency Front Load Washer, WFW8540FW, High Efficiency Front
Load Washer, Efficiency Front Load Washer, Front Load Washer, Load Washer
---|---