70mai A1ZHSU-zb5L Dash Cam Lite User Manual

70mai A1ZHSU-zb5L Dash Cam Lite

Product Information

The 70mai Dash Cam Lite is a high-quality dash cam equipped with a professional video recording chip and image sensor. It is designed to capture clear and detailed videos of your driving experiences.

Product Usage Instructions

1. Activating the 70mai Dash Cam Lite: To activate the dash cam, you need to download and install the 70mai app from the Google Play Store (Android) or App Store (iOS). Alternatively, you can scan the provided QR code to download the app. Once installed, open the app and select “Add Device” to complete the activation process following the on-screen prompts.
2. Product Overview: The dash cam features an indicator light, function buttons, a power button, speakers, a USB interface, and a memory card slot. These components are located on the device as shown in Figure 1.
3. Installation: Follow the steps below to install the dash cam:
4. Install the electrostatic sticker: Clean your windshield and place the electrostatic sticker on the recommended area, ensuring there are no air bubbles between the sticker and the glass.
5. Install the bracket: Attach the bracket to the dash cam until you hear a snap indicating it is securely in place.
6. Stick the camera mount to the windshield: Remove the protective cover from the mount and stick its base to the center of the electrostatic sticker. Ensure that the dash cam body is parallel to the ground.
7. Press the mount firmly to attach it securely to the electrostatic sticker.
8. Connect the USB cable to the cigarette lighter receptacle: Align the cable with the top edge of the windshield and secure it along the passenger’s side and the glovebox. Connect the cable to the car charger and insert the car charger into the cigarette lighter receptacle. Note that the position of the cigarette lighter receptacle may vary in different cars.
9. Adjust the dash cam angle: Turn on the dash cam and adjust the camera angle up and down using the preview screen to ensure it is facing the front.
10. Accessory: The dash cam can be used with the 70mai GPS Mount Holder (sold separately). Scan the provided QR code to access the online user guide for more information.

Please ensure that the dash cam is installed correctly to prevent product failure and injury to both the driver and passengers.

Package Contents

• 70mai Dash Cam Lite
• User Manual
• Regulatory Compliance Information
• WEEE Information
• EU Declaration of Conformity
• UKCA Declaration of Conformity

For more detailed information regarding regulatory compliance and declarations of conformity, please refer to the provided internet addresses.

View the User Guide for product functions and FAQs.
Scan the code to view the product functions, FAQs, and tutorial videos. https://fdashcam.70mai.com/support

Product Support

United States
1-877-746-6088
Canada (English)
1-888-507-9088
Mon-Fri 9am-6pm PST
https://dashcam.70mai.com/support 
help@70mai.com

Please read this manual carefully before using the product and keep it in a safe place.

Thank you for choosing the 70mai Dash Cam Lite
The 70mai Dash Cam Lite is equipped with a professional video recording chip and image sensor for capturing high-quality videos.

User guide

Please scan the QR code below to get the online user guide. Please use the product according to the instructions in the user guide.

Activating the 70mai Dash Cam Lite

The 70mai Dash Cam Lite must be activated using the 70mai app. To download and install the app, search for “70mai” in the Google Play Store (Android) or App Store (iOS).

Or you can download the app by scanning the QR code below:

Please select “Add Device” in the 70mai app and complete the activation according to the prompts.

Product Overview

Installation

Please install the product following the method below.

1. Install the electrostatic sticker
   Clean your windshield and put the electrostatic sticker on the recommended area as shown in the figure below.
   Make sure you remove air bubbles between the sticker and the glass.

2. Install the bracket
   Lock the bracket to the Dash Cam, as shown in the figure below. You will hear a snap when it is in place.

3. Stick the camera mount to the windshield
   Remove the protective cover from the mount and stick the mount’s base to the center of the electrostatic sticker. Make sure your Dash Cam body is parallel to the ground.
   Press the mount to attach it to the electrostatic sticker tightly.

4. Connect the USB cable to the cigarette lighter receptacle
   Align the cable with the top edge of the windshield and fasten it along the passenger’s side and the glovebox as shown below.
   Connect the cable to the car charger and insert the car charger into the cigarette lighter receptacle. Note : The cigarette lighter receptacle might be positioned differently in your car. The picture is provided for reference only.

5. Adjust the Dash Cam angle
   Turn on the Dash Cam and adjust the camera angle up and down against the preview screen to ensure that the camera is facing the front.

Accessory

This device can be used together with 70mai GPS Mount Holder (sold separately).
Please scan the QR code below to get the online user guide.

Safety precautions

Please read all precautions and instructions carefully before using this product to ensure proper and safe usage.

• This product records videos outside of moving vehicles. It can’t protect drivers and passengers from any accidents. We shall not take any responsibility if the user gets involved in any traffic accident and/or bear any loss due to product failure, information loss, or product operation.
• Due to differences in vehicle type, driving preferences, the environment, and other differences, parts of the product or the whole product may not work normally in some circumstances. The device may not record normally due to loss of power source, abnormal temperatures and/or humidity, collisions, damage to the TF card, and other reasons. We do not guarantee that all the recorded videos will be saved completely in any given situation. The images recorded by this product are for reference only.
• Install the product correctly. Do not block the driver’s vision. Do not obstruct the airbag. Keep the product at least 20cm away from the driver and passengers. Incorrect installation of the product may cause product failure and injury.
• Please use the car charger and USB cable that comes with this device to avoid compatibility issues. 70mai is not responsible for any loss caused by the use of non-standard car chargers and USB cables.
• The memory card is not included in the package. You will need to buy it by yourself.
• Use a TF card with storage capacity between 16GB and 64GB, and reading and writing speed is not lower than Class 10. Format the TF card before using it.
• Do not insert or pull out the TF card when the product is working to avoid damaging the TF card.
• TF card may be damaged after repetitive use. Replace TF cards in time to maintain proper recording. We shall not bear any responsibility caused by failed TF cards.
• This device is equipped with a built-in battery that is not removable. Do not disassemble the device yourself. The battery (battery pack or assembled battery) shall not be exposed to overheating environments such as sunlight, fire, or the like. If the battery is replaced improperly, there is a danger of explosion, so that it can only be replaced with a battery of the same or equivalent type.
• The device should not be exposed to water droplets or water splashes. Keep the device dry to avoid battery failure.
• If the battery is deformed, swelling, or leaking, stop using the product immediately and contact customer service.
• Do not shake or press the product. Strong impact or shaking may cause irreparable damage to the product.
• Do not clean this product by chemical solvents or cleansers.
• Keep this product away from strong magnetic fields to avoid damage.
• Do not use this product in temperatures higher than 60 or 10c
• Please note that the housing’s temperature rises when the device is running.
• Use this product within the scope of the law.

Specifications

• Model: Midrive D08
• Image sensor: SONY IMX307
• Resolution: 1920×1080
• Camera: FOV 130°
• Wireless connection: Wi-Fi IEEE 802.11 b/g/n/ 2.4GHz
• G-sensor: Acceleration sensor
• Expandable memory: MicroSD card with a capacity of 16-64GB and read/write speed of Class10 and above
• Supported OS: Android5.0/iOS11.0 and above
• Power supply: Car cigarette lighter
• Battery type: Li-polymer battery
• Battery capacity: 500mAh
• Input: 5V 1.5A
• Dimensions: 82 × 58.2 × 40.5mm

Package contents

• 70mai Dash Cam Lite ×1
• USB cable ×1
• Car charger ×1
• Electrostatic sticker ×1
• Heat-resistant adhesive ×1
• Mounting bracket ×1
• User manual ×1

**Regulatory compliance information

**

WEEE information
All products bearing this symbol are waste electrical and electronic equipment (WEEE as in directive 2012/19/EU) which should not be mixed with unsorted household waste. Instead, you should protect human health and the environment by handing over your waste equipment to a designated collection point for the recycling of waste electrical and electronic equipment, appointed by the government or local authorities. Correct disposal and recycling will help prevent potential negative consequences to the environment and human health. Please contact the installer or local authorities for more information about the location as well as the terms and conditions of such collection points.

EU declaration of conformity

The manufacturer hereby, declares that this equipment is in compliance with the applicable Directives and European Norms, and amendments. The full text of the EU Declaration of Conformity is available at the following internet address: https://help.70mai.asia/1193.html

Hereby, 70mai Co.,Ltd. declares that the radio equipment type Midrive D08 is in compliance with Radio Equipment Regulations 2017. The full text of the UKCA declaration of conformity is available at the following internet address: https://help.70mai.asia/2145.html

Cautions

• Disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, that can result in an explosion.
• Leaving a battery in an extremely high temperature surrounding environment that can result in an explosion or the leakage of flammable liquid or gas.
• A battery subjected to extremely low air pressure may result in an explosion or the leakage of flammable liquid or gas.
• This device is equipped with a built-in battery that cannot be removed or replaced. Do not disassemble or modify the battery by yourself.
• Replacement of a battery with an incorrect type can defeat a safeguard (for example, in the case of some lithium battery types).

FCC

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
FCC ID: 2AOK9-MIDRIVED08

Service: help@70mai.com
For further information, please go to www.70mai.com Manufacturer: 70mai Co., Ltd.
Address: Room 2220, Building 2, No. 588 Zixing Road, Minhang District, Shanghai, China

References

• 70mai: Innovator in Smart Dash Cams
• UK declaration of conformity

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>