STAR MICRONICS BSH-20B Wireless 2D Handheld Scanner User Guide

STAR MICRONICS BSH-20B Wireless 2D Handheld Scanner

Product Information

• The maximum operating ambient temperature for this product is 40 degree Celsius.
• Note: Any changes or modifications made to this equipment without the explicit approval of the responsible party for compliance may void the user’s authority to operate the equipment.

Product Usage Instructions

1. Ensure that the operating ambient temperature does not exceed 40 degrees Celsius. Operating the product in temperatures beyond this limit may result in performance issues or damage.
2. Do not attempt to make any changes or modifications to the equipment without explicit approval from the responsible party for compliance.
3. Follow all other instructions provided in the user manual for safe and proper use of the product.
4. If you encounter any issues or have questions regarding the product’s operation, refer to the troubleshooting section in the user manual or contact customer support for assistance.

Overview

Good Read LED:

• Red LED flashes slowly- Low battery alert.
• Red LED on – Scanner is charging.
• Red LED off and green LED on – Full charged
• Blue LED flashes slowly- Paired but no connection established.
• Blue LED on – Connection established.
• Green LED flashes once – Good read.

Communicate with the Host

Optimum Scanning

1. Press & hold Trigger. Illumination LED and Aiming LED cast an Illumination Pattern and an Aiming Pattern.
2. Keep Illumination Pattern in the center of a bar code. Zoom in and zoom out to allocate the Optimum Reading Stance.
3. On a successful reading, there will be a beep sound, illumination & aiming patterns die out. The Scanner then transmits barcode data to the Host.

NOTE, Experiences tell a certain range of distances has higher successful reading rate. This range is the Optimum Reading Distance.

Barcode Programming

1. Use of Programming Barcodes
2. Factory Defaults
3. Wireless Communication
4. NOTE: Windows 7 or previous system version is not available for Bluetooth HID mode.
5. Terminating Character Suffix
6. Scan Mode

Troubleshooting

When the scanner is not working, please:

1. Ensure that all cable connections are secure and that only the supplied cables are used.
2. Ensure that the barcode is not defaced. Wrinkled, soiled or torn barcodes might be unreadable.
3. Ensure that the barcode symbology is enabled. If the problem still persists, please contact your dealer or Star Micronics. When scanning barcodes on highly reflective surfaces, you may need to tilt the scanner by 15°.

Note:
In order not to affect battery life, we recommend that the scanner not be continuously plugged into a charger.

1. Replacement of a battery with an incorrect type that can defeat a safeguard (for example  in the case of some lithium battery types).
2. Disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, that can result in an explosion.
3. Leaving a battery in an extremely high temperature surrounding environment that can result in an explosion or the leakage of flammable liquid or gas.
4. A battery subjected to extremely low air pressure that may result in an explosion or the leakage off flammable liquid or gas.
5. Risk of fire or explosion if the battery is replaced by an incorrect type.

CE/NOM

• Marking and European Economic Area (EEA)
• Statement of Compliance
• We hereby declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU.
• The ventilation should not be impeded by covering the ventilation openings with items, such as newspapers, table-cloths, curtains, etc.;
• This product max operating ambient temperate is 40 degree C.
• Direct Current Symbo l

WEEE / UKCA

RECYCLING:

• This product bears the selective sorting symbol for Waste electrical and electronic equipment (WEEE).
• This means that this product must be handled pursuant to European directive 2012/19/EU in order to be recycled or dismantled to minimize its impact on the environment.

1. Bluetooth:
2. Maximum RF power : 6dBm.
3. frequency range: 2402-2480MHz
4. We hereby declares that this device is in compliance with the essential requirements and other relevant provisions of Radio Equipment Regulations 2017.
5. The full test of the UK declaration of conformity is available at the following internet address: www.starmicronics.com

FCC

Radio Frequency Interference Requirements Radio Transmitters (Part 15)
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

FCCID:SL9BSH-20B

Note

• This equipment has been tested and found to comply with the limits for a Class B digital device. pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an evidenced radio/ TV technician for help.

FCC/IC
Note: Changes or modifications to this equipment not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

IC

IC Statement

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:

1. This device may not cause interference, and
2. This device must accept any interference, including interference that may cause undesired operation of the device.

• The device is compliance with RF field strength limits, users can obtain Canadian information on RF exposure and compliance.
• This Class B digital apparatus complies with Canadian ICES-003.

For the detailed user manual and additional information please visit: www.starmicronics.com/help-center/

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>