STAR MICRONICS HS1210 Wireless 2D Hand Held Scanner User Guide

June 13, 2024
Star Micronics

STAR MICRONICS HS1210 Wireless 2D Hand Held Scanner

Product Information

Product Name: HS1210

FCC ID: 2BAQOHS1210

Product Usage Instructions

Caution: Any changes or modifications to this device not explicitly approved may void the warranty and could result in damage to the product or personal injury.

To use the HS1210, follow the steps below:

  1. Ensure that the device is fully charged before use.
  2. Press and hold the power button located on the device to turn it on.
  3. Once powered on, the HS1210 will enter the standby mode.
  4. To pair the device with your smartphone or other compatible devices, enable Bluetooth on the device you wish to connect and search for available devices.
  5. Select “HS1210” from the list of available devices on your device.
  6. If prompted, enter the PIN code provided in the user manual to complete the pairing process.
  7. Once successfully paired, you can now use the HS1210 for various purposes such as making and receiving calls, listening to music, and accessing voice assistant features.
  8. To adjust the volume, use the volume buttons located on the device.
  9. To turn off the device, press and hold the power button until the device powers off.

Please refer to the user manual for detailed instructions on advanced features and troubleshooting tips.

Overview

Good Read LED

  • Red LED flashes slowly- Low battery alert.
  • Red LED on – Scanner is charging.
  • Red LED off and green LED on – Full charged
  • Blue LED flashes slowly- Paired but no connection established.
  • Blue LED on – Connection established.
  • Green LED flashes once – Good read.

Communicate with the Host

Optimum Scanning

  1. Press & hold Trigger. Illumination LED and Aiming LED cast an Illumination Pattern and an Aiming Pattern.

  2. Keep Illumination Pattern in the center of a bar code. Zoom in and zoom out to allocate the Optimum Reading Stance.

  3. On a successful reading, there will be a beep sound, illumination & aiming patterns die out. The Scanner then transmits barcode data to the Host.

NOTE: Experiences tell a certain range of distances has higher successful reading rate. This range is the Optimum Reading Stance.

Barcode Programming

STAR MICRONICS HS1210 Wireless 2D Hand Held Scanner-
FIG6 STAR MICRONICS HS1210 Wireless 2D
Hand Held Scanner-FIG8

Troubleshooting

When the scanner is not working, please:

  1. Ensure that all cable connections are secure and that only the supplied cables are used.
  2. Ensure that the barcode is not defaced. Wrinkled, soiled or torn barcodes might be unreadable.
  3. Ensure that the barcode symbology is enabled.
    If the problem still persists, please contact your dealer or Newland customer service center.
    When scanning barcodes on highly reflective surfaces, you may need to tilt the scanner by 15°.

CE

Marking and European Economic Area (EEA) Statement of Compllance

  • We hereby declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU.
  • The ventilation should not be impeded by covering the ventilation openings with items, such as newspapers, table-cloths, curtains, etc.;
  • This product max operating ambient temperate is 60 degree C.
    Direct Current Symbol

WEEE / UKCA

RECYCLING:
This product bears the selective sorting symbol for Waste electrical and electronic equipment (WEEE).
This means that this product must be handled pursuant to European directive 2012/19/EU in order to be recycled or dismantled to minimize its impact on the environment.

  1. Bluetooth:
    Maximum RF power:0.08 dBm.
    frequency range: 2402-2480MHz

  2. We hereby declares that this device is in compliance with the essential requirements and other relevant provisions of Radio Equipment Regulations 2017.

  3. The full test of the UK declaration of conformity is available at the following internet address: www.starmicronics.com

FCC

Radio Frequency Interference Requirements Radio Transmitters (Part 15)

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

  1. This device may not cause harmful interference,and
  2. This device must accept any interference received, including interference that may cause undesired operation.

FCC ID: 2BAQOHS1210

Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installe d and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

IC

IC Statement
This device complies with Industry Canada license-exempt RSS standard(s).

Operation is subject to the following two conditions:

  1. this device may not cause interference, and
  2. this device must accept any interference, including interference that may cause undesired operation of the device.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals