Mytrix MTNSPC C02 Perry Yellow Bear Wireless Controller User Manual
- June 13, 2024
- mytrix
Table of Contents
- Product overview
- Specification
- Package Includes
- Wireless Connection & Wake Up Function
- Wake Up and Reconnect
- Controller Auto Sleep
- Wired Connection
- Audio Function
- Adjust Vibration Intensity
- Macro Definition Function
- Wired Connection on Windows PC
- Functions Comparison
- Adjust the Ears Light Modes
- Charging Instructions
- Calibrate the Control Sticks
- Warranty
- Company Information
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Mytrix MTNSPC C02 Perry Yellow Bear Wireless Controller User Manual
Product overview
3.5mm jack(only works when controller connects console via cable)
Specification
Input Voltage: 5V, 300mA.
Working Voltage: 3.7V
Battery Capacity: 300mAh Product Size: 13055102mm
Weight: 155+5g
Material: ABS
Package Includes
1x Controller
1x USB Type-C Charging Cable
1x User Manual
Wireless Connection & Wake Up Function
Please Note: Please make sure the AIRPLANE mode of the console is turned off before starting using.
First-Time Pairing:
- From the HOME menu of the console, select Controllers, then Change Grip/Order.
- Press and hold the “SYNC” button on the top of the controller for at least five seconds to power on the controller until all 4 LEDs flash. Once paired, all 4 LEDs will remain lit, and the controller will be shown on the screen.
Wake Up and Reconnect
Once the controller has paired with the console:
- If the console is in the SLEEP mode, the “HOME” button of the controller is able to wake up both the controller and the console.
- If the console is on, all the buttons are able to wake up the controller, the controller will reconnect to the console. If unable to connect, please follow the three steps:
- Turn off the AIRPLANE mode on the console
- Remove the controller’s information on the NS console (System Setting > Controllers and Sensors > Disconnect Controllers)
- Follow the First-Time Pairing steps
Controller Auto Sleep
- In the wireless connection, press and hold the HOME button for 3 seconds, the controller will be disconnected and turn into sleep mode.
- If no button is pressed within 5 minutes, the controller will automatically sleep.
- The controller sleeps when the controler is in SLEEP mode.
Wired Connection
-
Tum on the “Pro Controller Wired Communication” i the console: System Settings > Controllers and Sensors > Pro Controller Wired Communication > On Please Note: The *Pro Controller Wired Communication” must be. tumed on BEFORE connecting the controller and the Dock with the cable,
-
Set he Switch console on the Dock for the TV made, Connect the Switch Dock and the control lerdirctly with the USB Type C to A cable.
-
Press HOME bunion > Controllers > Change Grip Order. “The conirollericon with the “USB displayed on the screen indicates the wired connection i successful
Audio Function
“The controller has a 3.5mm audio port, supports 3.5mm wired headsets or
microphones.
Please Note: The audio function will ONLY work in the Wired Connection
Mode with a Switch console. And It will NOT work under the wireless connection
or when the controller s wired to a PC.
Please Note: The “Pro Controller Wired Communication” must be tumed on BEFORE connecting the controller and the Dock with the cable
- D System settings > Controllers and Sensors > Pro Controller ‘Wired Communication > On
- Set the Swish console on the Dock for the TV mode.
- ‘Connect the Switch Dock and the controlled with the USB cable.
- The fcon with “USB displayed indicates the wired connection s successful
- Plug the 3.5mm audio jack into the audio port on the bottom of the controller
Turbo and Auto-fire
Buttons Available to Set the Turbo Function: ABIXIYILIZURIZR bution
Set Up the Turbo Function:
-
Manual Turbo Function:
Press and hold the Turbo buton, then press any function bution ONCE to turn on the “Manual Turbo Functon”. -
Auto Turbo Function:
Repeat the first step above to switch to the *Auto Turbo Function”. -
Turn Off the Turbo Function:
Repeat the first step after the “Auto Turbo Function has been set,
Turn offal the turbo functions for all buttons:
Press and hold the Turbo button for 3 seconds, then press the subtract *
button 1o turn off the turbo functions of al buttons.
There Are Three Levels For the Turbo Speed: «
- Slow: 5 shots, the corresponding LED indicators will flash at & slow speeds.
- Medium: 12 shots , the corresponding LED indicators will flash ate medium speed. (Default Level)
- Fast: 20 cholis, the corresponding LED indicators wil flash at a fast speed
Adjust the Turbo Speed Levels:
Press and hold the Turbo button, push down the right joystick to decrease one
grade of turbo speed: pull up the right joystick to increase one grade of
urban speed.
‘You Gan Test and Check the Turbo Settings on a Console:
Settings > Controllers and Sensors > Test Input Devices > Test Controller Buttons
Adjust Vibration Intensity
Theirs Ars Four Levees of Vibration tani None, e, mcium song.
Adjust the Vibration Intensity:
- Press and hold the Turbo button, press the ‘-‘ button to decrease one grade of the vibration intensity;
- Press the ‘+’ button to increase one grade of vibration intensity
Macro Definition Function
There are two macro-enabled buttons “ML/MR” on the back of the controller, and a macro definition switch button “T”. Buttons “ML/MR” can be programmed into function button or buttons sequence respectively.
ML/MR Buttons Can Be Programmed to: A/B/X/Y/L/ZL/R/ZR/up/down/left/right buttons Enter the Macro Definition Mode and Set Up the Button(s):
Enter the Macro Definition Mode and Set Up the Button(s):
- Press the “T” button on the back of the controller for 3 seconds, the light “LED2-3” will flash slowly.
- Press the “ML” or “MR” button, the “LED2” light will flash slowly, the controller is ready to record the macro setting.
- Press the function buttons that need to be set in turn, the controller will record the button and the time interval of each button pressed.
- Press the “T” button to save, the “LED1” light will keep lit. The macro definition function will be memorized. When the controller re-connects to the console, it will automatically apply the last macro definition setting.
Clear the Macro Definition Settings: Press and hold the “T” button for 5
seconds until the “LED1-4” lights flash, all the current macro definition
settings will be cleared.
Example:
- Hold down the “T” button for 3 seconds until the “LED2-LED3” light flashes slowly.
- Press the “ML” button, the “LED2” light will flash slowly, the controller is ready to record. Press the “B” button, after 1 second press “A”, after 3 seconds press “X”, then press “T” to finish setting and save.
- The button “ML” now is set to perform “B (after 1s)→ A (after 3s) →X”.
You Can Test and Check the “MLIMR” Settings on a Console:
Settings > Controllers and Sensors > Test Input Devices > Test Controller
Bunions.
Wired Connection on Windows PC
PC XNPUT:
- Connect the controller to a Windows system computer with the USB cable, it will automatically be recognized as “X-INPUT” mode.
- The first and the fourth LEDS wil have a steady ligh.
Please Note: In the X-INPUT mode, button “A” becomes ‘B”, becomes “A”, X” becomes “Y”, and *Y” becomes °X”.
STEAM:
- Press down the right joysiick and connect the controller o the ‘computer with the USB cable.
- It il be recognized as the STEAM *Pro Controller” mode and ‘can be used for supported games.
Functions Comparison
Platform| Screenshot| Audio Function| Motion|
Vibration| Macro| Turbo
---|---|---|---|---|---|---
Switch Wireless| | x| | | |
Switch Wired| | | | | |
PC X-Input| x| x| x| | |
PC STEAM| x| x| x| | |
Adjust the Ears Light Modes
‘Three Light Effect Modes of Ears :
breathing mode — light on — light off
Adjust the Light Modes:
Afar the controller connects with the console, press both the “L* and “R buttons for § seconds to switch the lighting effact mod.
Charging Instructions
- The controlled can be charged using the Switch charger, the ‘Switch Dock, 5V 2A power adapter, or USB power supplies with the USB Type G to A cable.
- If the controllers connected with the console while charging, the corresponding channel LED ligh(s) on the controler wil lash. “The channal LED lighs) will stay It the controller has been fuly charged.
- If the controller is not connected with the console while charging, the 4 LED lights will lash. The LED lights wil go of when the controller has been full charged.
- When the battery is low, the comes ponding channel LED light(s) will flash; the controller il tun off and need to be charged f the. battery is exhausted.
Calibrate the Control Sticks
- Press the HOME button > System Settings > Controllers and ‘Sensors > Calibrate Control Sticks > Press the stick you want to calibrate
- Follow the on-screen instructions to verify the controlee functionality
Warranty
The product comes with a 1-year limited warranty. Our goal is to achieve total customer satisfaction, we will do our best to understand our customer’s requirements and always meet the requirements. If you have any questions, please do not hesitate to contact us via cs@mytrixtech.com. We will be more than happy to assist you.
Company Information
Company: Mytrix Technology LLC
Customer Service Tel: +1
978-496-8821
Customer Service Email: cs@mytrixtech.com
Web: www.mytrixtech.com
Address: 13 Garabedian Dr. Unit C, Salem NH 03079
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>