SAFAVIEH CHA4003 Birch Antler 30 Inch 6 Light Chandelier User Manual
- June 13, 2024
- SAFAVIEH
Table of Contents
Model#: CHA4003A/CHA4029A
Product Dimensions: Ø30” X 18.75”H
CHA4003 Birch Antler 30 Inch 6 Light Chandelier
WARNING
- WE RECOMMEND INSTALLATION OF THIS LIGHTING FIXTURE BE DONE BY A LICENSED ELECTRICIAN **
- Switch off the main electrical supply from the main fuse box / circuit breaker before installation.
- Inspect item carefully before attempting to install.
- If there is any damages or obvious defects, do not install.
- Item may not be returned once it has been installed.
CARE AND MAINTENANCE
- To clean the outside of the fixture, use a dry or slightly dampened clean cloth (use clean water, never a solvent) to wipe the surface of the fixture.
- To clean the inside of the fixture, first disconnect power to the fixture by turning off the circuit breaker or by removing the fuse at the fuse box. Next, use a dry or slightly dampened clean cloth (use clean water, never a solvent) to wipe the interior surface of the fixture.
- Do not use any cleaners with chemical, solvents or harsh abrasives. Use only a dry soft cloth to dust or wipe carefully.
NOTICE& IMPORTANT SAFETY INSTRUCTIONS
- Please make sure that you have all parts indicated before you begin assembly of this item
- This item should be assembled on a soft surface to prevent scratching the finish during assembly
- To reduce the risk of fire, electrical shock or injury to persons or property, please follow the guideline below for safe use and installation
- The external flexible cable or cord of this lamp cannot be replaced If the cord is damaged, the lamp shall be destroyed
Part List and Hardware List
PIEC E| D ESC R IPTIO N| PICTU RE| Q UAN TITY| PIECE|
D ESC R IP TIO N| PIC TUR E| Q U AN TITY
---|---|---|---|---|---|---|---
A| W ire N ut| | 3 X| H| C losable link/cap| | 2 X
B| M ounting Plate| | 1 X| I| Fixture Loop| | 1 X
C| G round S crew| | 1 X| J| C hain|
| 1 X
D| M ounting Screw Size:8 /32* 30m m| | 2 X| K| Socket sleeve| | 6 X
E| C anopy| | 1 X| L| Bulb| | 6 X
F| H anging Loop| | 1 X| M| Lam p B oby| | 1 X
G| Canopy Nut| | 1 X| N| Finial| | 1 X
PREPARATION
- Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list and hardware contents list.
- If any part is missing or damaged, do not attempt to assemble the product.
- Estimated Assembly Time:30 minutes
- If you are having difficulty, our friendly Customer Care team is always here to help. Please email customersupport@safavieh.com
NOTE: PLEASUE USE TYPE”B” BULB MAX 40-WATT OR CFL BULB MAX 13-WATT OR LED MAX 9-WATT THERE ARE 6 X 4W LED BULBS IN THE BOX.
Step 1: Unpack all parts from cartons carefully. Screw the Chain(J) to the Hanging Loop(F) and the Fixture Loop (I) with Closable link/cap (H) as diagram.
Step 2: Weave the 2 wire power cord and bare ground wire through every other loop to the top of chain(J),center holes of Hanging Loop(F)&Canopy(E)&Mounting Plate(B) as diagram. Insert the threaded tube of the Mounting Plate(B)into the center hole of the Hanging Loop(F),rotate the Mounting Plate(B) clockwise till tight. Slide the Canopy Nut(G) then the Canopy(E) to the end of the Chain(J).
Step 3: Wire connection
Connect fixture neutral wire (ribbed) to the outlet box neutral wire (usually
white) using a wire nut. Connect fixture hot wire (smooth with markings) to
the outlet box hot wire (usually black) using a wire nut.
CAUTION: Do not reverse the hot and neutral connections Grounding
Instructions:
Wrap ground wire from outlet box around green ground screw(B) on mounting
bracket, no less than 2″ from wire end. Tighten ground screw. If fixture is
supplied with a ground wire, connect to outlet ground wire with a wire
connector.
Step 4: Attach the Mounting Plate (B) onto the junction box by inserting
two Mounting Screws (D) and turning clockwise till tight. Slide the Canopy (E)
upward along the chain(J)till the ceiling surface. Fix the Canopy(E) by
rotating the Canopy Nut(G)clockwise to engage it with the threaded portion of
the Hanging Loop (F)until secure. Do not over tighten this nut.
Attach the Finial(N) onto the threaded portion of the bottom of the lamp body
and rotate it clockwise till tight. Place each Socket Sleeve(K) onto each
socket until secure. Insert the bulbs(L) into the sockets until secure.
DO NOT EXCEED THE SPECIFIED WATTAGE.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>