GE APPLIANCES AZ45E07DAB Zoneline Cooling and Electric Heat Unit Instruction Manual
- June 13, 2024
- GE Appliances
Table of Contents
GE APPLIANCES AZ45E07DAB Zoneline Cooling and Electric Heat Unit
Product Information
- Product Name: AZ45E07DAB
- Specification Revised: 6/22
Dimensions and Installation Information (in inches):
- Wall Sleeve Dimensions: A = 21 inches, B = 58 inches, C = 42-1/4 inches
- Wall Opening Dimensions: Minimum H = 16-1/4 inches, Minimum W = 42-1/4 inches
Electrical Connection:
- All wiring, including installation of receptacle, must be made in accordance with national and local electrical codes and regulations.
- 230/208 volt units may be plugged into a receptacle.
- Power connection kits are required on all Zoneline chassis.
Ducted Applications:
- AZ45 and AZ65 Series can be used with ductwork to heat or cool more than one room.
- RAK6053 Duct Adaptor is applied to the top of the case over the air discharge.
- RAK601B Duct Extension is applied to the right or left of the adaptor.
- Locally fabricated ductwork may be added to extend to a maximum recommended straight distance of 15 feet in one direction.
Heater Information:
AZ45/65 Heater KW| 230/208 Volt Line Cord (P)| Direct (D)| Sub-base Connected
Units
---|---|---|---
7K/9K| RAK315P| RAK315D| RAK204D15C
12K/15K| RAK320P| RAK320D| RAK204D20C
Product Usage Instructions
Electrical Wiring:
Ensure that all wiring, including the installation of the receptacle, is
done in accordance with national and local electrical codes and regulations.
Ducted Applications:
If you want to heat or cool more than one room, you can use the AZ45 and
AZ65 Series with ductwork. Follow these steps:
- Apply the RAK6053 Duct Adaptor to the top of the case over the air discharge.
- Apply the RAK601B Duct Extension to the right or left of the adaptor.
- You may add locally fabricated ductwork to extend to a maximum recommended straight distance of 15 feet in one direction.
Electrical Connection:
If you have a 230/208 volt unit, it can be plugged into a receptacle.
However, please note that power connection kits are required for all Zoneline
chassis.
Wall Sleeve Dimensions:
The wall sleeve dimensions should be as follows:
- A = 21 inches
- B = 58 inches
- C = 42-1/4 inches
Add 1/4 inch to A and C dimensions for all cut-outs.
Wall Opening Dimensions:
The minimum wall opening dimensions should be as follows:
- Minimum H = 16-1/4 inches
- Minimum W = 42-1/4 inches
Add 1/4 inch to A and C dimensions for all cut-outs.
Heater Information:
Depending on the model and voltage, refer to the table below for the
appropriate heater information:
AZ45/65 Heater KW| 230/208 Volt Line Cord (P)| Direct (D)| Sub-base Connected
Units
---|---|---|---
7K/9K| RAK315P| RAK315D| RAK204D15C
12K/15K| RAK320P| RAK320D| RAK204D20C
Note: For detailed electrical connection information, including the use of a sub-base for direct connected units, please refer to the Architects and Engineers Design Data Manual.
For more information, please visit our website at zoneline.com or contact us at Hospitality.Direct@geappliancs.com.
Specification Revised: 6/22
AZ45E07DAB
GE Zoneline® Cooling and Electric Heat Unit, 230/208 Volt
FEATURE AND BENEFITS
- Cooling capacity – 7,200/7,000 BTU
- Energy efficiency – 13.4/13.4 EER
- Dehumidification – 1.64 pints/hour
- Indoor fan CFM (high/low) – 350/220
- Electronic touch controls with LED display
- Quiet operation – Baked-on mastic sound barrier,
- cross flow blower and two DC fan motors create less
- noise to ensure comfort
- SMC base pan and bulkhead – No rusting and helps block noise.
- Heat & Freeze Sentinels – Keeps the room from overheating or freezing
- Electronic temperature limiting – Prevents expensive over-cooling or over-heating of the room
- Fresh air vent CFM (fully open high fan) – 33*
- R-410A refrigerant
- *When using the RAKVENT1 kit
DIMENSIONS AND INSTALLATION INFORMATION (IN INCHES)
ELECTRICAL WIRING
All wiring, including installation of receptacle, must be made in accordance
with national and local electrical codes and regulations.
NOTE: Aluminum wiring may pose special problems – consult a qualified
electrician.
GRILLE OPTIONS
- Stamped Aluminum Grille – RAG60
- Exterior Architectural Louvers Durable
- Polycarbonate: RAG61 (Beige), RAG62 (Maple), RAG63 (Dark Brown)
- Extruded Aluminum Architectural Grille – RAG67
RETROFIT KITS:
RAK40 – Deflector Kit to adapt chassis for use with non-GE exterior louvered
grilles.
DUCTED APPLICATIONS
AZ45 and AZ65 Series can be used with ductwork to heat or cool more than one
room. RAK6053 Duct Adaptor is applied to the top of case over the air
discharge. RAK601B Duct Extension is applied to right or left of adaptor.
Locally fabricated ductwork may be added to extend to maximum recommended
straight distance of 15 feet in one direction.
ELECTRICAL CONNECTION
- 230/208 volt units may be plugged into a receptacle. See Architects and Engineers Design Data Manual for electrical connection information including use of sub-base for direct connected units. Installation must comply with local electrical codes and regulations.
- Power connection kits are required on all Zoneline chassis.
WALL SLEEVE DIMENSIONS
-
*RAB81 WALL SLEEVE**
Heavy-gauge steel, 4 pc design with insulation. A–42″, B–13-3/4″, C–16″ Also available in 16″, 18″, 20″ and 24″ depths -
RAB78B WALL SLEEVE
4 pc Fiberglass reinforced polyester compound with stainless steel locking components. A–42″, B–14″, C–16″
MAXIMUM CORD EXTENSION WALL OPENING DIMENSIONS Add 1/4″ to A and C dimensions for all cut-outs. 16-1/4″ Min. H x 42-1/4″ Min. W
AZ45/65 HEATER KW
230/208 VOLT| LINE CORD (P), DIRECT (D) AND SUB-BASE CONNECTED UNITS
7K/9K| 12K/15K
Power Connection Kit| RAK315P RAK315D RAK204D15C| RAK320P RAK320D
RAK204D20C| RAK330P RAK330D RAK204D30C| RAK315P RAK315D RAK204D15C|
RAK320P RAK320D RAK204D20C| RAK330P RAK330D RAK204D30C
Total Watts| 2410/1990| 3420/2830| 4830/3990| 2430/2020| 3450/2860| 4860/4020
Heater Watts| 2400/1960| 3400/2780| 4800/3930| 2400/1960| 3400/2780| 4800/3930
Heater BTU| 8100/6600| 11600/9400| 16300/13400| 8100/6600| 11600/9400|
16300/13400
Total Amps| 10.5/9.6| 14.9/13.6| 21.0/19.2| 10.6/9.7| 15.1/13.8| 21.2/19.3
(MCA)| 15| 20| 30| 15| 20| 30
Recommended Protective Device (MOCP)| 15 amp time- delay fuse or breaker| 20
amp time- delay fuse or breaker| 30 amp time- delay fuse or breaker| 15 amp
time- delay fuse or breaker| 20 amp time- delay fuse or breaker| 30 amp time-
delay fuse or breaker
For more information please visit our website at zoneline.com or message Hospitality.Direct@geappliancs.com .
Specification Revised 6/22
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>