CTA AUT-CFVMS Aluminum Security Vehicle Mount Instruction Manual

CTA AUT-CFVMS Aluminum Security Vehicle Mount

Product Information

The Aluminum Security Vehicle Mount (AUT-CFVMS) is a versatile mount designed to securely hold a tablet in a vehicle. It comes with a set of vehicle seat rail clamps, screws, and an allen key for easy installation. The mount features adjustable joints and a lockable tablet holder.

Package Contents:

• A – Vehicle Mount
• B – Vehicle Seat Rail Clamps Bundle
• C – Clamp Base
• D – Screw M10x12L
• E – Hex Allen Key

Product Usage Instructions

Assembling Rail Clamp Footing of the Vehicle Mount:
Because each vehicle is different, you will need to determine which included seat rail clamp is best for you.

• Choose the clamp base (J) with the angle that matches your needs.
• Align the preferred clamp (C) and the vehicle mount (A) and rotate in screw (D) with provided allen key tool (E).

Installing Vehicle Mount to your Vehicle Seat Rail:
(Seat and rail not included)

• Loosen the bolt (not included) of the seat rail.
• Install the fully assembled vehicle mount on the seat rail and screw the bolt back as shown. (Tool not included)

How to Adjust the Joints:

• Twist the screw knobs counter-clockwise to release the connection.
• Adjust the arm to your preferred position and rotate back clockwise until securely tightened.

Inserting a Tablet into Holder:

• Identify the key hole of the lock on the back of the holder. When inserting the key, if you rotate it to the right, it unlocks, and rotating to the left locks.
• When locking the holder, make sure the lock is pressed forward into the holder. Insert the key, turn, and remove the key. When unlocking the holder, unlock with the key first, then pull out to release it and access the tablet.
• After unlocking the holder, adjust the arms and place them over the corners of your tablet. Avoid placing the holder over the corner with the tablet’s camera. Push the arms back onto the corners until firmly set and secure.

Note : The tablet shown in illustrations is for demonstration purposes only. Tablet cases are not supported by the holder, so be sure to remove any case before inserting your tablet.

1. 1. Once you have adjusted the corners to fit your tablet, push the lock into the holder. Then use your key as illustrated and rotate it to the lock position before removing the key.

2. Routing Charging Cable:
3. Insert the rubber component into the side of the holder facing your device’s charging port. Place the cable as shown.
4. Fish the wire in the back towards the cable clips to help hold the cable in place. Carefully route it from clip to clip until it comes out the side or bottom as preferred.

For further assistance, please contact our customer support at 888-733-4448">888-733-4448.

Package Contents

Instructions

1. Assembling Rail Clamp Footing of the Vehicle Mount:
   • Because each vehicle is different, you will need to determine which included seat rail clamp is best for you.
   • Choose the clamp base (J) with the angle that matches your needs.
   • Align the preferred clamp (C) and the vehicle mount (A) and rotate in screw (D) with provided allen key tool (E).
2. Installing Vehicle Mount to your Vehicle Seat Rail:
   • Loosen the bolt (not included) of the seat rail.(seat and rail not included)
   • Install the full assembled vehicle mount on the seat rail and screw the bolt back as shown. (Tool not included)
3. How to Adjust the Joints:
   • Twist the screw knobs counter-clockwise to release the connection. Adjust the arm to your any preferred position & rotate back clockwise until securely tightened.
4. Inserting a Tablet into Holder
   • Identify the key hole of the lock on the back of the holder. When inserting the key, if you rotate it to the right, it unlocks and rotating to the left locks.
   • When locking the holder, you need to make sure the lock is pressed forward into the holder, the insert key and turn and remove key. When unlocking the holder, you need to first unlock with key, then pull out to release it to access the tablet.
   • After you have unlocked the holder, you can adjust the arms and place it over the corners of your tablet. Make sure you are not placing the holder over the corner that has the camera on the tablet. That would block your camera for usage. Push the arms back onto the corners until firmly set and secure.
   • Once you have the corners adjusted to your tablet. Push the lock into the holder. Then use your key as illustrated and rotate to the lock position and then remove key. Tablet holder does not support tablet cases, so be sure to remove case if on your tablet.

Insert a rubber component into the side of the holder facing your device’s charging port. Place cable as shown. Fish the wire in the back towards the cable clips to help hold the cable in place and carefully route it from clip to clip until out the side or bottom as preferred. (Shown above in both images)

HELP:

• ADDRESS : 36 Taaffe Place Brooklyn. NY 11205
• SUPPORT : support@ctadigital.com
• CALL : 888-733-4448
• VISIT : www.ctadigital.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>