HOTONE Binary Eko Delay Effects Pedal Owner’s Manual

HOTONE Binary Eko Delay Effects Pedal Owner’s Manual

Welcome

Congratulations on your new Hotone Binary pedal! You have just added some serious power to your pedalboard.

The Binary series lets loose versatile pro effects in compact cases. A dual- DSP powered platform and CDCM modeling system ensure a realistic playing experience, dual-footswitch design and variable I/Os make it easy to use, and an OLED screen offers clear, detailed display.

Binary Eko is a CDCM-based multi modulation effects pedal with stereo I/O and expression pedal support, delivering precise classic delay pedal sounds along with new and inspiring Hotone original delay effects.

Features

• Grown out of next-gen XTOMP technology
• Compact, easy-to-use dual footswitch delay pedal with tap tempo
• Advanced CDCM modeling system ensures realistic playing experience
• Dual DSP-powered platform ensures high sound quality
• 24-bit A/D/A conversion, up to 110dB S/N ratio
• 17 high quality delay effects including CDCM-based classics and Hotone originals
• Variable maximum delay time ranging from 1000ms to 4000ms
• Tap Tempo function with Tap Divide
• Stereo I/Os
• EXP jack for expression pedal control
• USB jack for firmware upgrading, loading/managing effects with free PC/Mac software
• 10 Presets (2 banks x 5 patches)
• Built-in OLED screen with clear display
• 5 transparent knobs with LEDs
• 9V DC power supply

Panel Introduction

1. ON/OFF: For switching this unit on/off. The LEDs under the upper 5 knobs indicate effect on/off status.
2. PATCH/TAP: Tap for selecting forward patches in current bank, hold for engaging/disengaging tap tempo mode.
3. +/- buttons: For selecting effects and adjusting parameters.
4. GLOBAL: For setting expression pedal, input mode, and other parameters.
5. SAVE/EXIT button: For saving or canceling parameter changes.
6. OLED screen: Shows bank/patch numbers, setting values and other operation info.
7. MIX: Controls effect wet/dry signal ratio (varies with effects).
8. 9. A/B: Control detailed effect character (varies with effects).
9. F.BACK: Controls the delay feedback amount (varies with effects).
10. TIME: Controls the delay time (varies with effects). In Tap Tempo mode, the TIME LED will keep flashing.
11. INPUT: 1/4” (6.35mm) stereo jack, for plugging in instruments or other effects. A Y cable is needed when connecting to stereo pedal outputs.
12. EXP: 1/4” (6.35mm) TRS jack, for connecting expression pedals. The expression pedal should have a TRS cable attached to it. We recommend using a Hotone Soul Press (switched to EXP mode) for expression control.
13. 15. OUTPUT (L & R): 1/4” (6.35mm) mono jacks, for connecting to amps or other effects.
14. USB jack: Mini USB jack, for effects editing, firmware updates, and factory reset.
15. DC 9V: Plug in your power supply here (DC 9V, center negative).

Connections

Note: TURN ON FIRST, TURN OFF LAST. Always mute the mixer/audio interface before plugging or unplugging power jacks, cables, etc. When you’re using a mixer or an audio interface, please adjust the onboard knobs carefully to avoid signal clipping.

Plugging in your power supply will turn on the device. The main display will come up as shown below:

1. Current bank/patch number
2. Shows the expression pedal controlled parameter
3. Indicates the effect you’re using in current patch

Select a Patch/Bank

Tap the PATCH footswitch once to switch to the next patch. Tap it repeatedly to cycle through patches of the current bank in the order 1, 2, 3, 4, 5, then

Tap the two footswitches at the same time to switch to the next bank. Tap them repeatedly to cycle through banks in the order A, B, then A.

Tap Tempo

Hold the PATCH/TAP footswitch to engage Tap Tempo mode when the effect is on. Then tap the PATCH/TAP footswitch to set a tempo speed. In this mode, the LED under the TIME knob will pulse to indicate the effect time you set. Hold the PATCH/TAP footswitch again to disengage.

Global

Press the GLOBAL button repeatedly to cycle through input mode, max delay time, expression pedal, and trail settings:

Use the +/- buttons to set the parameters, press the SAVE/EXIT button (or wait for 5 seconds without any operation) to confirm settings and exit to the main display.

Edit

1. Adjust the parameters
   Use the onboard knobs to adjust the effect parameters. The screen display will be shown as below when adjusting:

2. Current parameter value you’re adjusting (shown: feedback)

3. Saved parameter value in the current patch (PREV. = Previous value)
   Note: In this status, you can use the +/- buttons to fine tune the delay time.

4. Select a different effect
   Use the +/- button to change to another effect:
   
   The inverted bank/patch number indicates that the current patch has been edited.

5. Set the expression pedal
   If you have an expression pedal, you can control an effect parameter in real time. In main display, press the GLOBAL button three times to edit control target:
   
   Use the +/- buttons to select a target among OFF, MIX, A, B, F.BACK, TIME.
   Note: If you change to another patch before saving your edits, all your changes will be lost. Save the patches to keep your changes.

Save

Hold the SAVE/EXIT button to activate save function. The screen will be shown as below:

Use the +/- buttons to choose a location. Tap the SAVE/EXIT button to confirm saving.

Tap PATCH/TAP footswitch to cancel saving and go back to edit status.

Input Mode, Max Delay Time and Trail

Max delay time
In main display, press the GLOBAL button twice to set a max delay time:

Use the +/- buttons to choose from 1000ms/2000ms/3000ms/4000ms. The default setting is 1000ms.

Trail
A trail will affect the effect “tail” when you turn off the pedal. When trail is on, the delay repeats will continue after you bypass the effect; when trail is off, the effect will disappear immediately. The default trail setting is OFF. In main display, press the GLOBAL button seven times until the message below is shown:

Use the +/- buttons to select trail on/off.

Input mode, max delay time and trail settings are all global settings (it won’t change your patches) and changes will be automatically saved.

Expression Pedal Range and Calibration

In main display, press the GLOBAL button four times/five times to set the minimum/maximum value ranging from 000 to 100:

• 4 times (min value)

• 5 times (max value)

Parameter value

Note:

1. The minimum value cannot be set higher than the maximum value.
2. This is a global setting (it won’t change your patches) and changes will be automatically saved.

Expression Pedal Range and Calibration

The expression pedal can be calibrated if necessary. If there does not seem to be much effect even when you press the pedal, or effects change greatly when the pedal only moves slightly, use the following procedure to readjust it. In the main display, press the GLOBAL button six times:

Press + button to activate calibration and then screen displays “HEEL POSITION”:

Press the pedal all the way back towards the heel and press + button, and then it displays “TOE POSITION”:

Press the pedal all the way forward towards the toe and press + button. After finishing the adjustment, “CALIBRATION COMPLETE” will appear and it will go back to the main display.

If “PLEASE TRY AGAIN” appears, do the calibration from “HEEL POSITION” again:

Effect Models List

TIME
02| 80 EKO| Based on Maxon AD80| MIX| Mod depth(M. DEPTH)| Mod rate(M. RATE)| F.BACK| 20ms-1000ms/2000ms/3000ms/4000ms| TIME
03| MEMO EKO| Based on Electro-Harmonix Stereo Memory Man| E.LEVEL| Mod depth(M. DEPTH)| Mod rate(M. RATE)| F.BACK| 20ms-1000ms/2000ms/3000ms/4000ms| TIME
04| 900 EKO| Based on Maxon AD900| E.LEVEL| Mod depth(M. DEPTH)| Mod rate(M. RATE)| F.BACK| 20ms-1000ms/2000ms/3000ms/4000ms| TIME
05| 999 EKO| Based on Maxon AD999| E.LEVEL| Mod depth(M. DEPTH)| Mod rate(M. RATE)| F.BACK| 20ms-1000ms/2000ms/3000ms/4000ms| TIME
06| PURE EKO| Producing pure delay effect| MIX| Mod depth(M. DEPTH)| Mod rate(M. RATE)| F.BACK| 20ms-1000ms/2000ms/3000ms/4000ms| TIME
07| WARM EKO| Producing delay with warm, analog-feel feedback| MIX| Mod depth(M. DEPTH)| Mod rate(M. RATE)| F.BACK| 20ms-1000ms/2000ms/3000ms/4000ms| TIME
08| TAPE EKO| Simulates vintage tape echo machine| MIX| Low cut(LO CUT)| High cut(HI CUT)| F.BACK| 20ms-1000ms/2000ms/3000ms/4000ms| TIME
09| TUBE EKO| Simulates tube driven echo machine| MIX| Low cut(LO CUT)| High cut(HI CUT)| F.BACK| 20ms-1000ms/2000ms/3000ms/4000ms| TIME
10| Vintage Rack (VINT RACK)| Simulates 1980’s rack digital delay sound withslightly downsampled feedback| MIX| MOD| TONE| F.BACK| 20ms- 1000ms/2000ms/3000ms/4000ms| TIME
11| DUAL EKO| Producing dual delay effect with pure feedback| MIX| Feedback A(FB A)| Time A: 20ms- 1000ms/2000ms/3 000ms/4000ms| Feedback B(FB B)| Time B : 20ms- 1000ms/2000ms/3000ms/4000ms| Time B
12| PING PONG| Producing delay effect that bounces back and forth between left and right channels| MIX| Mod depth(M. DEPTH)| Mod rate(M. RATE)| F.BACK| 20ms- 1000ms/2000ms/3000ms/4000ms| TIME
13| Sweep Eko (SWP EKO)| Producing delay effeect with sweeping filter| MIX| Sweep filter Q(Q)| Sweep rate(S. RATE)| F.BACK| 20ms- 1000ms/2000ms/3000ms/4000ms| TIME
14| Tremolo Eko (TRM EKO)| Producing delay effect with tremolo modulation| MIX| Tremolo depth(T. DEPTH)| Tremolo rate(T. RATE)| F.BACK| 20ms- 1000ms/2000ms/3000ms/4000ms| TIME
15| LOFI EKO| Producing delay effect with sample reducedfeedback| MIX| Low cut(LO CUT)| High cut(HI CUT)| F.BACK| 20ms-1000ms/2000ms/3000ms/4000ms| TIME
16| RING EKO| Producing delay effect with ring modulated feedback| MIX| Ring mod frequency(FREQ)| Ring mod tone(TONE)| F.BACK| 20ms-1000ms/2000ms/3000ms/4000ms| **** TIME
17| SLAP BACK| Simulates vintage slap back echo sound| MIX| Mod depth(M. DEPTH)| Mod rate(M. RATE)| F.BACK| 10ms-200ms fixed| TIME

The Manufacturers and product names mentioned above are trademarks or registered trademarks of their respective owners. The trademarks were used merely to identify the sound character of the products.

Specifications

Numbers of Effects: 17
Numbers of Patches: 10 (2 banks x 5 patches)
Max. Delay Time: 4000ms
Digital Processing: 24-bit A/D/A conversion, 44.1 kHz sample rate
Frequency Response: 20 Hz-20 kHz
S/N Ratio: Up to 110dB
Input Impedance: 1M Ohms
Output Impedance: 100 Ohms
Power Requirement: DC 9V, center negative
Current Consumption: 200mA minimum
Dimensions: 121mm (D) x 72mm (W) x 47mm (H)
Weight: 340g

The contents of this manual are subject to change without notice.

References

• Manual-Hub.com – Free PDF manuals!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>