SAFAVIEH SCN4072A Lighting Fixture Instruction Manual

SAFAVIEH SCN4072A Lighting Fixture

Product Information

• Model: SCN4072A
• Product Dimensions: 6W X 8.25D X 12.5H
• Part List:
  • A Wire Connector – 3X
  • B Mounting Plate – 1X
  • C Mounting Screw – 2X
  • D Ground Screw – 1X
  • E Retaining Screw – 2X
  • F Lamp Body – 1X
  • G Glass Shade – 1X
  • H Cap – 1X
  • I Socket Ring – 1X
  • J Bulb – 1X
• Recommended Bulb: Type A bulb max 40-watt or LED bulb max 9-watt (LED 9-watt bulb included in the box)

Product Usage Instructions

1. WARNING: We recommend installation of this lighting fixture be done by a licensed electrician. Switch off the main electrical supply from the main fuse box / circuit breaker before installation.

2. Inspect the item carefully before attempting to install. If there are any damages or obvious defects, do not install.

3. NOTICE & IMPORTANT SAFETY
   INSTRUCTIONS

   • Please make sure that you have all parts indicated before you begin assembly of this item.
   • This item should be assembled on a soft surface to prevent scratching the finish during assembly.
   • To reduce the risk of fire, electrical shock, or injury to persons or property, please follow the guideline below for safe use and installation.
   • The external flexible cable or cord of this lamp cannot be replaced. If the cord is damaged, the lamp shall be destroyed.

Step 1 Unpack all parts from cartons carefully. Fix the Mounting Plate (B) to the junction box with Mounting Screw(C).

Step 2 :Wire connection

• * Connect fixture neutral wire (ribbed) to the outlet box neutral wire (usually white) using a wire connector (A).

  • Connect fixture hot wire (smooth with markings) to the outlet box hot wire (usually black) using a wire connector (A). CAUTION: Do not reverse the hot and neutral connections.

Grounding Instructions

• * Wrap ground wire from outlet box around green ground screw (D) on mounting bracket, no less than 2 inches from wire end. Tighten ground screw.

  • If fixture is supplied with a ground wire, connect it to the outlet ground wire with a wire connector (A).

Step 3  Tuck wires inside junction box.

1. Step 4: Place the Glass Shade (G) and Cap (H) over the socket, then secure with the Socket Ring (I).
2. Attach the Lamp Body (F) to the Mounting Plate (B) and secure with Retaining Screw (E).
3. Insert the bulb (J) into the Socket.

WARNING

• WE RECOMMEND INSTALLATION OF THIS LIGHTING FIXTURE BE DONE BY A LICENSED ELECTRICIAN **
• Switch off the main electrical supply from the main fuse box / circuit breaker before installation.
• Inspect item carefully before attempting to install.
• If there is any damages or obvious defects, do not install.
• Item may not be returned once it has been installed.

CARE AND MAINTENANCE

• To clean the outside of the fixture, use a dry or slightly dampened clean cloth (use clean water, never a solvent) to wipe the surface of the fixture.
• To clean the inside of the fixture, first disconnect power to the fixture by turning off the circuit breaker or by removing the fuse at the fuse box. Next, use a dry or slightly dampened clean cloth (use clean water, never a solvent) to wipe the interior surface of the fixture.
• Do not use any cleaners with chemical, solvents or harsh abrasives. Use only a dry soft cloth to dust or wipe carefully.

NOTICE& IMPORTANT SAFETY INSTRUCTIONS

• Please make sure that you have all parts indicated before you begin assembly of this item
• This item should be assembled on a soft surface to prevent scratching the finish during assembly
• To reduce the risk of fire, electrical shock or injury to persons or property, please follow the guideline below for safe use and installation
• he external flexible cable or cord of this lamp cannot be replaced If the cord is damaged, the lamp shall be destroyed

Part List and Hardware List

A

| ****

Wire Connector

| |

3X

| ****

F

| ****

Lamp Body

| |

1X

B

| ****

Mounting Plate

| |

1X

| ****

G

| ****

Glass Shade

| |

1X

C

| ****

Mounting Screw

| |

2X

| ****

H

| ****

Cap

| |

1X

D

| ****

Ground Screw

| |

1X

| ****

I

| ****

Socket Ring

| |

1X

E

| ****

Retaining Screw

| ****

| ****

2X

| ****

J

| ****

Bulb

| |

1X

PREPARATION

• Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list and hardware contents list.
• If any part is missing or damaged, do not attempt to assemble the product.
• Estimated Assembly Time: 20 minutes.
• If you are having difficulty, our friendly Customer Care team is always here to help. Please email customersupport@safavieh.com

NOTE : PLEASE USE TYPE”A” BULB MAX 40-WATT OR LED BULB MAX 9-WATT, THERE IS LED 9-WATT BULB IN THE BOX

Step 1 Unpack all parts from cartons carefully. Fix the Mounting Plate(B) to the junction box with Mounting Screw (C).

Step 2 Wire connection Connect fixture neutral wire (ribbed) to the outlet box neutral wire (usually white) using a wire connector (A). Connect fixture hot wire (smooth with markings) to the outlet box hot wire (usually black) using a wire connector (A).
CAUTION : Do not reverse the hot and neutral connections Grounding Instructions: Wrap ground wire from outlet box around green ground screw(D) on mounting bracket, no less than 2″ from wire end. Tighten ground screw. If fixture is supplied with a ground wire, connect to outlet ground wire with a wire connector (A).

Step 3  Tuck wires inside junction box. Attach the Lamp Body (F) to the Mounting Plate (B) and secure with Retaining Screw (E).

Step 4 Place the Glass Shade (G) and Cap (H) over the socket, the secure with the Socket Ring (I). Insert the bulb (J) into the Socket.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>